Common use of Performance documents Clause in Contracts

Performance documents. These plans take into account the Tender Specifications and technical provisions, the design drawings of the project developer and general architecture plans, stability plans and special techniques plans annexed to these Tender Specifications. All implementation plans and detail plans are to be submitted for approval to the contracting authority along with calculation notes, technical approvals and technical forms and in particular those related to the works and the equipment listed below (non-exhaustive list): • Upgrade foundations in view of works planned • Stability: plans for slabs, posts and beams, stairs or any prefabricated component • Sealing • Finishing of rooms (walls, floor and ceiling) • Inside and outside drainage • List of stones • Roof covering, roof carpentry • Façades • Partition walls • False ceilings • Furniture based on tender documents • Lights layout plan • Plan of metal joinery (banisters, handrails, gangway, porch) • Outside joinery, List of inside joinery • Plan of special techniques The managing official may refuse technical forms which are partial, incomplete or too commercial and do not provide the technical information required for assessment and approval. Samples of ironware, heating, electricity or plumbing fixtures or any similar pieces will be submitted for approval to the managing official who will, for that purpose, refer to the project developer's advice and the approved model will remain on the construction site until the placement of the last piece of its kind. At the request of the contracting authority, the building contractor shall also provide the following documents during the performance period: • Samples of materials proposed corresponding to the technical forms. • Colour shade cards of determine the choice of colour • Test reports, technical manuals, technical approvals, technical. • Products or equipment used for this contract.

Performance documents. These plans take into account consider the Tender Specifications and technical provisions, the design drawings of the project developer and general architecture plans, stability plans and special techniques plans annexed to these Tender Specifications. All implementation plans and detail plans are to be submitted for approval to the contracting authority along with calculation notes, technical approvals and technical forms and in particular those related to the works and the equipment listed below (non-exhaustive list): • Upgrade foundations in view of works planned • Stability: plans for slabs, posts and beams, stairs or any prefabricated component • Sealing • Finishing of rooms (walls, floor and ceiling) • Inside and outside drainage • List of stones • Roof covering, roof carpentry • Façades • Partition walls • False ceilings • Furniture based on tender documents • Lights layout plan • Plan of metal joinery (banisters, handrails, gangway, porch) • Outside joinery, List of inside joinery • Plan of special techniques The managing official may refuse technical forms which are partial, incomplete or too commercial and do not provide the technical information required for assessment and approval. Samples of ironware, heating, electricity or plumbing fixtures or any similar pieces will be submitted for approval to the managing official who will, for that purpose, refer to the project developer's advice and the approved model will remain on the construction site until the placement of the last piece of its kind. At the request of the contracting authority, the building contractor shall also provide the following documents during the performance period: • Samples of materials proposed corresponding to the technical forms. • Colour shade cards of determine the choice of colour • Test reports, technical manuals, technical approvals, technical. • Products or equipment used for this contract.

Performance documents. These plans take into account the Tender Specifications and technical provisions, the design drawings of the project developer and general architecture plans, stability plans and special techniques plans annexed to these Tender Specifications. All implementation plans and detail plans are to be submitted for approval to the contracting authority along with calculation notes, technical approvals and technical forms and in particular those related to the works and the equipment listed below (non-exhaustive list): • ): 1. Upgrade foundations in view of works planned • Stability: planned; 2. Stability plans for slabs, posts and beams, stairs stains or any prefabricated component • Sealing • component; 3. Sealing; 4. Inside and outside drainage; 5. Finishing of rooms (walls, floor and ceiling) • Inside and outside drainage • ); 6. List of stones • stones; 7. Roof coveringcovering roof carpentry; 8. Facades; 9. Partition walls, roof carpentry • Façades • Partition walls • False ceilings • false ceilings; 10. Furniture based on tender documents • documents; 11. Lights layout plan • plan; 12. Plan of metal joinery (banistersbaristers, handrailshand rails, gangway, porch) • ; 13. Outside joinery, ; List of inside joinery • joinery; 14. Plan of special techniques techniques. The managing official may refuse technical forms which are partial, incomplete or too commercial and do not provide the technical information required for assessment and approval. Samples of ironware, heating, electricity or plumbing fixtures or any similar pieces will be submitted for approval to the managing official who will, for that purpose, refer to the project developer's advice and the approved model will remain on the construction site until the placement of the last piece of its kind. At the request of the contracting authority, the building contractor shall also provide the following documents during the performance period: • : 1. Samples of materials proposed corresponding to the technical forms; 2. • Colour shade cards of determine the choice of colour • colour 3. Test reports, technical manuals, technical approvals, technical; 4. • Products or equipment used for this contract.

Performance documents. These plans take into account the Tender Specifications and technical provisions, the design drawings of the project developer and general architecture plans, stability plans and special techniques plans annexed to these Tender Specifications. All implementation plans and detail plans are to be submitted for approval to the contracting authority along with calculation notes, technical approvals and technical forms and in particular those related to the works and the equipment listed below (non-exhaustive list): • ): 1. Upgrade foundations in view of works planned • Stability: planned; 2. Stability plans for slabs, posts and beams, stairs stains or any prefabricated component • Sealing • component; 3. Sealing; 4. Inside and outside drainage; 5. Finishing of rooms (walls, floor and ceiling) • Inside and outside drainage • ); 6. List of stones • stones; 7. Roof coveringcovering roof carpentry; 8. Facades; 9. Partition walls, roof carpentry • Façades • Partition walls • False ceilings • false ceilings; 10. Furniture based on tender documents • documents; 11. Lights layout plan • plan; 12. Plan of metal joinery (banistersbarristers, handrailshand rails, gangway, porch) • ; 13. Outside joinery, ; List of inside joinery • joinery; 14. Plan of special techniques techniques. The managing official may refuse technical forms which are partial, incomplete or too commercial and do not provide the technical information required for assessment and approval. Samples of ironware, heating, electricity or plumbing fixtures or any similar pieces will be submitted for approval to the managing official who will, for that purpose, refer to the project developer's advice and the approved model will remain on the construction site until the placement of the last piece of its kind. At the request of the contracting authority, the building contractor shall also provide the following documents during the performance period: • : 1. Samples of materials proposed corresponding to the technical forms; 2. • Colour shade cards of determine the choice of colour • colour 3. Test reports, technical manuals, technical approvals, technical; 4. • Products or equipment used for this contract.