POD WIRING INTERFACE REQUIREMENTS FOR LEAR Sample Clauses

POD WIRING INTERFACE REQUIREMENTS FOR LEAR x. Operation of AST 1, AST-6, ALQ-167, and ALE 43 pods by one C-12311/AL Universal Control Box (UCB) requires twelve #20 AWG wires and one #20 AWG shielded twisted pair (or biaxial cable) to each wing store station. Ten of the 12 wires (doubled up for current handling capacity) provided the phase 115 VAC 400 Hz prime power, neutral and aircraft ground to the pods from the aircraft. The other two wires (for MIL 1553B data bus signals) terminate at the UCB at the operator's station. Additionally, two wires for +28 VDC return must be supplied to the UCB from the aircraft. And if it is desired to use a Weight on Wheels (WOW) switch to inhibit unintended transmissions and chaff dispensing, another wire will be required to supply that indication to the UCB. b. UP to ten conductors are used in the cable connected to the UCB at the operator's station. The cable connector must mate with the MS; 120E16-26P connector mounted on the rear of the UCB. The pin assignments are: Pin Function Description A DATA BUS HI Half of MIL 1553B shielded twisted pair B DATA BUS LO Half of MIL 1553B shielded twisted pair F DATA SHIELD Shield of MIL 1553B twisted pair (or triax) 1 ALE IDI Ground indicating chaff pod presence on Sta #1 B DISP CMD1 + 28 volt DISPENSE COMMAND (to ALE-43 #1) K ALE ID2 Ground indicating chaff pod presence on Sta #2 C DISP CMD2 +28 volt DISPENSE COMMAND (to ALE-43 #1) G GND -28 volt return and ground (from A/C) V +28 VDC A/C +28 volt power for UCB (from A/C) W WOW (OPTIONAL) Ground = Weight on Wheels (from A/C) Up to fifteen conductors may be used in wing wiring out to each wing station pylon where one of two pod-umbilical cables will be attached. Attachment 1 108 1. For the AST-6 and ALQ-167 pods, the umbilical cable should terminate with a connector that will mate with the MS3110P22-555 connector mounted on the pod shell. The pin assignments are: Pin Function Description --- -------- ----------- h DATA BUS HI Half of MIL 1553B shielded twisted pair I DATA BUS LO Half of MIL 1553B shielded twisted pair m DATA SHIELD Shield of MIL 1553B TWISTED pair (or triax) E GND Ground (from A/C) N. M PHASE A 115 VAC 400 HZ Phase A prime power (from A/C) R. P PHASE B 115 VAC 400 HZ Phase B prime power (from A/C) T. S PHASE C 115 VAC 400 HZ Phase C prime power (from A/C) L. V. G NEUTRAL 115 VAC 400 HZ Neutral (from A/C)
Sample 1
AutoNDA by SimpleDocs

Related to POD WIRING INTERFACE REQUIREMENTS FOR LEAR

  • SERVICE REQUIREMENTS FOR REFERRED CLIENTS A. Agent agrees to respond to any communications from a Referred Client within two (2) hours after receipt if such communication is received between 9:00am to 5:00pm local time. For communications received outside of these hours, Agent agrees to respond by 10:00am the next day. B. Agent agrees to update XXXX.xxx with status updates within 48 hours after initial communication with a Referred Client and upon every significant status change until closing or abandoned. Updates shall be made by Agent via email to xxxxxxxxxxxx@xxxx.xxx. C. Vacations or extended absences shall be reported, with length of pause, to XXXX.xxx via email to D. Agent will not add Referred Client to any email list or calling list without the express permission of Referred Client. E. Agent agrees XXXX.xxx has the right to survey the Referred Client at any time. F. If Agent is contacted by a Referred Client that Agent is unwilling or unable to assist, Agent shall direct such Referred Client back to XXXX.xxx for assistance and notify XXXX.xxx at xxxxxxxxxxxx@xxxx.xxx. G. Agent agrees that XXXX.xxx has no obligation to provide Agent with any number of referrals and that prospective clients are free to select the agent they wish to work with for any particular real estate transaction.

  • Minimum Customer Support Requirements for TIPS Sales Vendor shall provide timely and commercially reasonable support for TIPS Sales or as agreed to in the applicable Supplemental Agreement.

  • Minimum Site Requirements for TIPS Sales (when applicable to TIPS Sale). Cleanup: When performing work on site at a TIPS Member’s property, Vendor shall clean up and remove all debris and rubbish resulting from their work as required or directed by the TIPS Member or as agreed by the parties. Upon completion of work, the premises shall be left in good repair and an orderly, neat, clean and unobstructed condition. Preparation: Vendor shall not begin a project for which a TIPS Member has not prepared the site, unless Vendor does the preparation work at no cost, or until TIPS Member includes the cost of site preparation in the TIPS Sale Site preparation includes, but is not limited to: moving furniture, installing wiring for networks or power, and similar pre‐installation requirements. Registered Sex Offender Restrictions: For work to be performed at schools, Vendor agrees that no employee of Vendor or a subcontractor who has been adjudicated to be a registered sex offender will perform work at any time when students are, or reasonably expected to be, present unless otherwise agreed by the TIPS Member. Vendor agrees that a violation of this condition shall be considered a material breach and may result in the cancellation of the TIPS Sale at the TIPS Member’s discretion. Vendor must identify any additional costs associated with compliance of this term. If no costs are specified, compliance with this term will be provided at no additional charge. Safety Measures: Vendor shall take all reasonable precautions for the safety of employees on the worksite, and shall erect and properly maintain all necessary safeguards for protection of workers and the public. Vendor shall post warning signs against all hazards created by the operation and work in progress. Proper precautions shall be taken pursuant to state law and standard practices to protect workers, general public and existing structures from injury or damage. Smoking: Persons working under Agreement shall adhere to the TIPS Member’s or local smoking statutes, codes, ordinances, and policies.

  • Interface Requirements 2.4.5.1 The NID shall be equal to or better than all of the requirements for NIDs set forth in the applicable industry standard technical references.

  • Minimum Shipping Requirements for TIPS Sales Vendor shall ship, deliver, or provide ordered goods and services within a commercially reasonable time after acceptance of the order. If a delay in delivery is anticipated, Vendor shall notify the TIPS Member as to why delivery is delayed and provide an updated estimated time for completion. The TIPS Member may cancel the order if the delay is not commercially acceptable or not consistent with the Supplemental Agreement applicable to the order.

  • Meteorological Data Reporting Requirement (Applicable to wind generation facilities only)

  • Selection of Subcontractors, Procurement of Materials and Leasing of Equipment The contractor shall not discriminate on the grounds of race, color, religion, sex, national origin, age or disability in the selection and retention of subcontractors, including procurement of materials and leases of equipment. The contractor shall take all necessary and reasonable steps to ensure nondiscrimination in the administration of this contract. a. The contractor shall notify all potential subcontractors and suppliers and lessors of their EEO obligations under this contract. b. The contractor will use good faith efforts to ensure subcontractor compliance with their EEO obligations.

  • Minimum Condition and Warranty Requirements for TIPS Sales All goods quoted or sold through a TIPS Sale shall be new unless clearly stated otherwise in writing. All new goods and services shall include the applicable manufacturers minimum standard warranty unless otherwise agreed to in the Supplemental Agreement.

  • Project Requirements 1. Project must conform to regulations under 24 CFR Part 92, commonly known as the HOME Regulations.

  • Software Requirements 7 Developer shall prepare the Project Schedule using Oracle’s Primavera P6.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!