Polishing Sample Clauses

Polishing. (1) monthly: Door plates, kick plates, and brass and metal fixtures within the building will be wiped daily and polished monthly.

Polishing. All doorplates, kick plates, brass and metal fixtures within the building will be wiped weekly and polished quarterly.

Polishing. All the Brass/SS door handles/door knobs, hand railings, lift walls, other brass fittings are required to be polished and kept in shining condition by using approved quality polishing agents including buffing as and when directed. Twice a year.

Polishing. The basic shape of the sheet so acquired is then polished with the help of a three-roll calendar. At the same time the sheet is cooled by circulating water in the rolls of the calendar and thereafter on a roller table by atmospheric air.

Polishing. French polish shall conform to IS-348 - 1981. Take a wad of cotton wool and partially saturated it with the polish, enclose the wad in a piece of fine cloth and rub it hard along the grain with light even pressure. Should the wad showed any sign of sticking, it should be slightly dipped in linseed oil and continue rubbing until a thinly coated semi-gloss appearance is obtained. Set aside for about two hours to permit surface coat to xxxxxx. Rub furnace with sand paper „C‟ to remove any raised gain. Repeat polish to the surface as before when a clear grained smooth surface is obtained. It shall be allowed to xxxxxx for about one hour. Rub surface again with No „C‟ sand paper, recharge wad as before and apply to the surface in circular motion until the surface is covered all over, charge the wad with wax polish & applywith straight strokes in direction of the grains until the required gloss is obtained to the approval of the GE.

Polishing. The surfaces will be polished by grinding using manual or mechanical process to give a smooth, even, perfect plane surface or as may be directed. The polished surface should reflect light like a mirror and must be free from searches and depressions.

Polishing. Activated carbon is used to remove the residual trace contaminants. During this step, a pH adjustment is also made before rejecting the treated purged water. The [ * ] extracted from the physical-chemical system is mixed with the tars and oils as well as with the fines and carbon to form an emulsion that is sent to the gasifier for conversion of all organic matter into simple gases and to capture the inorganic matter as oxides or salts by the cyclones. If, for whatever reason the sewer bylaw norms are not met, the water and/or the [ * ] (before being re-injected) will be placed in a labelled container and kept in a separate area of the plant before being transferred to a designated treatment facility for final appropriate disposal. The effluent will respect the rejection norms for the City of Edmonton. The treated purged water will be tested every [ * ] for toxicity and for internal quality purposes, treated purged water will also be tested weekly at the plant. (refer to Monitoring section for more details).

Polishing. When polishing any natural stone the COMPANY does not make any guarantees as to a specific “gloss level”. There are several different qualities of natural stone, varying amounts of fill from tile to tile; lighting in any one area can influence this too. Some natural stone is prone to absorb the polishing compound(s) to varying degrees that we may use. The COMPANY is not responsible for a pristine result based on factors that we have no control of or that were not considered in the contract.

Polishing. As Necessary All door plates kick plates and brass and metal fixtures within the building shall be polished as necessary and residue from floor maintenance cleaned as necessary.

Polishing. All door plates, kick plates, brass and metal fixtures within the building will be wiped weekly and polished periodically. THIS INSTRUMENT PREPARED BY AND RETURN TO: Xxxxx X. Xxxxxxxxx, Esq. Holland Knight LLP X.X. Xxx 0000 Xxxxx, XX 00000-0000 THIS SUBORDINATION, NON-DISTURBANCE, AND ATTORNMENT AGREEMENT (the “Agreement”) is made and entered into this _________ day of April, 2000, by and among AMSOUTH BANK, an Alabama state-chartered bank (“Lender”), whose address is ATTN: Xxxx Xxxxx, Xxxxx 000, Xxxxxxxx X, 00000 Feather Xxxxx Xxxxx, Xxxxxxxxxx, XX 00000, and MIRAMAR 75. L.L.C., a Delaware limited liability company (“Landlord”), whose address is 0000 X. Xxxxxxx Xxxxxx, Xxxxx 000, Xxxxx, Xxxxxxx 00000, and ROYAL CARIBBEAN CRUISES LTD., a Liberian corporation (“Tenant”), whose address is ____________________________________________________________ .