Statistical Analysis 31 F-tests and t-tests will be used to analyze OV and Quality Acceptance data. The F-test is a 32 comparison of variances to determine if the OV and Quality Acceptance population variances 33 are equal. The t-test is a comparison of means to determine if the OV and Quality Acceptance 34 population means are equal. In addition to these two types of analyses, independent verification 35 and observation verification will also be used to validate the Quality Acceptance test results.
Statistical Sampling Documentation a. A copy of the printout of the random numbers generated by the “Random Numbers” function of the statistical sampling software used by the IRO.
Data Analysis In the meeting, the analysis that has led the College President to conclude that a reduction- in-force in the FSA at that College may be necessary will be shared. The analysis will include but is not limited to the following: ● Relationship of the FSA to the mission, vision, values, and strategic plan of the College and district ● External requirement for the services provided by the FSA such as accreditation or intergovernmental agreements ● Annual instructional load (as applicable) ● Percentage of annual instructional load taught by Residential Faculty (as applicable) ● Fall Full-Time Student Equivalent (FFTE) inclusive of dual enrollment ● Number of Residential Faculty teaching/working in the FSA ● Number of Residential Faculty whose primary FSA is the FSA being analyzed ● Revenue trends over five years for the FSA including but not limited to tuition and fees ● Expenditure trends over five years for the FSA including but not limited to personnel and capital ● Account balances for any fees accounts within the FSA ● Cost/benefit analysis of reducing all non-Residential Faculty plus one Residential Faculty within the FSA ● An explanation of the problem that reducing the number of faculty in the FSA would solve ● The list of potential Residential Faculty that are at risk of layoff as determined by the Vice Chancellor of Human Resources ● Other relevant information, as requested
Rectification of Safety Hazard 60.12 Where, because of the existence of a safety hazard, a site has been stopped for a defined period of time and Employees sent off site by agreement between Site Managers and any combination of Union Official/s, Health and Safety Committee, those people who remain on site to do rectification work will be paid at the rate of double time for all such work.
Department Review If a mutually acceptable solution has not been reached during Step 1, and the employee intends to pursue the grievance formally, the employee shall submit the grievance in writing on the Employee Grievance Resolution Form to the Department Head with a copy to the Labor Relations Division not later than ten (10) working days after the supervisor’s written response. The Department Head shall consider the grievance and render a written decision within ten (10) working days of receipt of the formal grievance. The written decision shall include a clear and concise statement including the reason(s) for the decision. The Department Head may hold a meeting with the employee to achieve any of the following purposes: 1) to identify why the employee feels there is a grievance and facilitate communication and resolution; 2) to clearly identify issues and areas of agreement/disagreement; and 3) to have the parties present whatever available information/ documentation necessary to fully attempt to resolve the grievance. The employee may be accompanied by his/her shop xxxxxxx during the Department Review, provided that the xxxxxxx is in the same department as the employee, and has been identified by the employee on the Employee Grievance Resolution Form. If the department, in consultation with the Labor Relations Division, determines that the grievance is outside of the Department Head’s authority, or the grievance involves employees working in separate departments, then such grievance shall be submitted to Step 3.
Material Safety Data Sheet Seller shall provide to Buyer with each delivery any Material Safety Data Sheet applicable to the work in conformance with and containing such information as required by the Occupational Safety and Health Act of 1970 and regulations promulgated thereunder or its State approved counterpart.
MATERIAL SAFETY DATA SHEETS Contractor is required to ensure Material Safety Data Sheets (“MSDS”) are available, employees are trained in the use of MSDS, and MSDS are in a readily accessible place at the Site. This requirement applies to all materials with an associated MSDS per the federal “Hazard Communication” standard or employees’ Right-to-Know laws. Contractor is also required to ensure proper labeling and training on any substance brought onto the Site and that any person working with the material (or who is subject to possible exposure by use of the material or contact with the material), is informed of the possible and/or real hazards of the substance, and follows proper handling and protection procedures.
Technical Standards Applicable to a Wind Generating Plant i. Low Voltage Ride-Through (LVRT) Capability A wind generating plant shall be able to remain online during voltage disturbances up to the time periods and associated voltage levels set forth in the standard below. The LVRT standard provides for a transition period standard and a post-transition period standard.
DATA COLLECTION AND ANALYSIS The goal of this task is to collect operational data from the project, to analyze that data for economic and environmental impacts, and to include the data and analysis in the Final Report. Formulas will be provided for calculations. A Final Report data collection template will be provided by the Energy Commission. The Recipient shall: • Develop data collection test plan. • Troubleshoot any issues identified. • Collect data, information, and analysis and develop a Final Report which includes: o Total gross project costs. o Length of time from award of bus(es) to project completion. o Fuel usage before and after the project.
SAFETY AND ACCIDENT PREVENTION In performing work under this Contract on State premises, Contractor shall conform to any specific safety requirements contained in the Contract or as required by law or regulation. Contractor shall take any additional precautions as the State may reasonably require for safety and accident prevention purposes. Any violation of such rules and requirements, unless promptly corrected, shall be grounds for termination of this Contract in accordance with the default provisions hereof.
