Common use of Primary requirements Clause in Contracts

Primary requirements. a) Products as defined in section 3 and placed on the EU market by Signatories after 1 January 2014 shall comply with the specifications of ENERGY STAR ® v2.0 and default duplex settings requirements set out in sections b) and c) below in accordance with the following targets: Period OM products placed on the EU market TEC products placed on the EU market Tier 0* Jan-Dec 2014 N/A N/A Tier I Jan-Dec 2015 88% 70% Tier II Jan-Dec 2016 90% 80% *Baseline report NB: Products placed on the EU market between 1 January and 31 December 2013 remain subject to version 4 of the Voluntary Agreement. For the purposes of compliance with this section, the rate of compliance shall be calculated following the methodology described in Annex B. b) The specifications in ENERGY STAR ® v2.0 concern6: • Energy consumption requirements (TEC and OM products); • Default delay times (OM products); and • Duplex availability (TEC products). c) According to the table below, and for TEC products in the relevant speed category introduced after 1 January 2014, duplex-printing is set as default when printing from the computer, meaning that the relevant software (driver or firmware) shall be configured so that the first print-job will be in duplex unless the print settings have been modified at the stage when the product is first installed to function as intended. 6 ENERGY STAR ® Program Requirements for Imaging Equipment – Eligibility Criteria (Rev. Jun-2013) Automatic Duplexing Requirements for all Color TEC Copiers, MFDs, and Printers Monochrome Product Speed, s, as Calculated in the Test Method (ipm; BW) Automatic Duplexing Requirement Default Duplex set at shipment or installation s ≤ 19 None Not applicable 19 < s < 35 Integral to the base product or optional accessory At discretion of either the user or manufacturer s ≥ 35 Integral to the base product Required Automatic Duplexing Requirements for all Monochrome TEC Copiers, MFDs, and Printers Monochrome Product Speed, s, as Calculated in the Test Method (ipm) Automatic Duplexing Requirement Default Duplex set at shipment or installation s ≤ 24 None Not applicable 24 < s < 37 Integral to the base product or optional accessory At discretion of either the user or manufacturer s ≥ 37 Integral to the base product Required

Primary requirements. a) Products as defined in section 3 and placed on the EU market by Signatories after 1 January 2014 shall comply with the specifications of ENERGY STAR ® v2.0 and default duplex settings requirements set out in sections b) and c) below in accordance with the following targets: Period OM products placed on the EU market TEC products placed on the EU market Tier 0* Jan-Dec 2014 N/A N/A Tier I Jan-Dec 2015 88% 70% Tier II Jan-Dec 2016 90% 80% *Baseline report NB: Products placed on the EU market between 1 January and 31 December 2013 remain subject to version 4 of the Voluntary Agreement. For the purposes of compliance with this section, the rate of compliance shall be calculated following the methodology described in Annex B. b) The specifications in ENERGY STAR ® v2.0 concern6: •  Energy consumption requirements (TEC and OM products); •  Default delay times (OM products); and •  Duplex availability (TEC products). c) According to the table below, and for TEC products in the relevant speed category introduced after 1 January 2014, duplex-printing is set as default when printing from the computer, meaning that the relevant software (driver or firmware) shall be configured so that the first print-job will be in duplex unless the print settings have been modified at the stage when the product is first installed to function as intended. 6 ENERGY STAR ® Program Requirements for Imaging Equipment – Eligibility Criteria (Rev. Jun-2013) Automatic Duplexing Requirements for all Color TEC Copiers, MFDs, and Printers Monochrome Product Speed, s, as Calculated in the Test Method (ipm; BW) Automatic Duplexing Requirement Default Duplex set at shipment or installation s ≤ 19 None Not applicable 19 < s < 35 Integral to the base product or optional accessory At discretion of either the user or manufacturer s ≥ 35 Integral to the base product Required Automatic Duplexing Requirements for all Monochrome TEC Copiers, MFDs, and Printers Monochrome Product Speed, s, as Calculated in the Test Method (ipm) Automatic Duplexing Requirement Default Duplex set at shipment or installation s ≤ 24 None Not applicable 24 < s < 37 Integral to the base product or optional accessory At discretion of either the user or manufacturer s ≥ 37 Integral to the base product Required

Primary requirements. ‌ a) Products as defined in section 3 and placed on the EU market by Signatories after 1 January 2014 shall comply with the specifications of ENERGY STAR ® v2.0 and default duplex settings requirements set out in sections b) and c) below in accordance with the following targets: Period OM products placed on the EU market TEC products placed on the EU market Tier 0* Jan-Dec 2014 N/A N/A Tier I Jan-Dec 2015 88% 70% Tier II Jan-Dec 2016 90% 80% *Baseline report NB: Products placed on the EU market between 1 January and 31 December 2013 remain subject to version 4 of the Voluntary Agreement. For the purposes of compliance with this section, the rate of compliance shall be calculated following the methodology described in Annex B. b) The specifications in ENERGY STAR ® v2.0 concern6: • Energy consumption requirements (TEC and OM products); • Default delay times (OM products); and • Duplex availability (TEC products). c) According to the table below, and for TEC products in the relevant speed category introduced after 1 January 2014, duplex-printing is set as default when printing from the computer, meaning that the relevant software (driver or firmware) shall be configured so that the first print-job will be in duplex unless the print settings have been modified at the stage when the product is first installed to function as intended. 6 ENERGY STAR ® Program Requirements for Imaging Equipment – Eligibility Criteria (Rev. Jun-2013) Automatic Duplexing Requirements for all Color TEC Copiers, MFDs, and Printers Monochrome Product Speed, s, as Calculated in the Test Method (ipm; BW) Automatic Duplexing Requirement Default Duplex set at shipment or installation s ≤ 19 None Not applicable 19 < s < 35 Integral to the base product or optional accessory At discretion of either the user or manufacturer s ≥ 35 Integral to the base product Required Automatic Duplexing Requirements for all Monochrome TEC Copiers, MFDs, and Printers Monochrome Product Speed, s, as Calculated in the Test Method (ipm) Automatic Duplexing Requirement Default Duplex set at shipment or installation s ≤ 24 None Not applicable 24 < s < 37 Integral to the base product or optional accessory At discretion of either the user or manufacturer s ≥ 37 Integral to the base product Required

Primary requirements. a) Products as defined in section 3 and placed on the EU market by Signatories after 1 January 2014 shall comply with the specifications of ENERGY STAR STAR® v2.0 and default duplex settings requirements set out in sections b) and c) below in accordance with the following targets: Period OM products placed on the EU market TEC products placed on the EU market Tier 0* Jan-Dec 2014 N/A N/A Tier I Jan-Dec 2015 88% 70% Tier II Jan-Dec 2016 90% 80% *Baseline report NB: Products placed on the EU market between 1 January and 31 December 2013 remain subject to version 4 of the Voluntary Agreement. For the purposes of compliance with this section, the rate of compliance shall be calculated following the methodology described in Annex B. b) The specifications in ENERGY STAR STAR® v2.0 concern6: •  Energy consumption requirements (TEC and OM products); •  Default delay times (OM products); and •  Duplex availability (TEC products). c) According to the table below, and for TEC products in the relevant speed category introduced after 1 January 2014, duplex-printing is set as default when printing from the computer, meaning that the relevant software (driver or firmware) shall be configured so that the first print-job will be in duplex unless the print settings have been modified at the stage when the product is first installed to function as intended. 6 ENERGY STAR 6ENERGY STAR® Program Requirements for Imaging Equipment – Eligibility Criteria (Rev. Jun-2013) ). Automatic Duplexing Requirements for all Color TEC Copiers, MFDs, and Printers Monochrome Product Speed, s, as Calculated in the Test Method (ipm; BW) Automatic Duplexing Requirement Default Duplex set at shipment or installation s ≤ 19 None Not applicable 19 < s < 35 Integral to the base product or optional accessory At discretion of either the user or manufacturer s ≥ 35 Integral to the base product Required Automatic Duplexing Requirements for all Monochrome TEC Copiers, MFDs, and Printers Monochrome Product Speed, s, as Calculated in the Test Method (ipm) Automatic Duplexing Requirement Default Duplex set at shipment or installation s ≤ 24 None Not applicable 24 < s < 37 Integral to the base product or optional accessory At discretion of either the user or manufacturer s ≥ 37 Integral to the base product Required