Refer to 3 Sample Clauses
Refer to 3. 5 of this agreement for additional guidance on the application of these provisions.
Refer to 3. 2.1 Translation Mode for the explanation of the article toolbar.
We use cookies on our site to analyze traffic, enhance your experience, and provide you with tailored content.
For more information visit our privacy policy.Account Verification Whether or not a Default or Event of Default exists, Agent shall have the right at any time, in the name of Agent, any designee of Agent or any Borrower, to verify the validity, amount or any other matter relating to any Accounts of Borrowers by mail, telephone or otherwise. Borrowers shall cooperate fully with Agent in an effort to facilitate and promptly conclude any such verification process.
Accounting Terms and Calculations Except as may be expressly provided to the contrary herein, all accounting terms used herein shall be interpreted and all accounting determinations hereunder shall be made in accordance with GAAP. To the extent any change in GAAP affects any computation or determination required to be made pursuant to this Agreement, such computation or determination shall be made as if such change in GAAP had not occurred unless the Borrower and the Bank agree in writing on an adjustment to such computation or determination to account for such change in GAAP.
Safety Data Sheets If specified by City in the solicitation or otherwise required by this Contract, Contractor must send with each shipment one (1) copy of the Safety Data Sheet (SDS) for each item shipped. Failure to comply with this procedure will be cause for immediate termination of the Contract for violation of safety procedures.
Description of Goods As ordered by the JBE pursuant to this Agreement under a Participating Addendum, Contractor shall provide to the JBEs the following products, goods, materials, and supplies (“Goods”), free and clear of all liens, claims, and encumbrances, and in accordance with this Agreement:
Inspection of Goods 8.1 The Buyer shall inspect the goods upon delivery. 8.2 Where goods are damaged the Buyer shall notify the Supplier. The Buyer may reject the damaged goods and the following provisions shall apply: 8.2.1 the Supplier shall collect the damaged goods from the Buyer at the Supplier’s expense; 8.2.2 during the period between delivery of the goods to the Buyer and collection by the Supplier, the Buyer shall not be liable for any loss or further damage caused to the damaged goods; 8.2.3 all sums payable by the Buyer in relation to the damaged goods shall cease to become payable; 8.2.4 all sums paid by the Buyer in relation to the damaged goods shall be repaid by the Supplier immediately; 8.2.5 the Buyer shall be entitled to claim damages from the Supplier for any losses caused to the Buyer as a result of the goods being damaged. 8.3 Where there are shortages in the order the Buyer shall notify the Supplier and the following provisions shall apply: 8.3.1 all sums payable by the Buyer in relation to the missing goods shall cease to become payable; 8.3.2 all sums paid by the Buyer in relation to the missing goods shall be repaid by the Supplier immediately; 8.3.3 the Buyer shall be entitled to claim damages from the Supplier for any losses caused to the Buyer as a result of the shortages. 8.4 If the Buyer so requests, the Supplier shall immediately replace damaged goods or supply goods which are missing at the Supplier’s expense or the Buyer shall be entitled to cancel, without notice, the whole or any unexecuted part of the order and the rights referred to in Clause 5.2 shall apply. 8.5 Where there is an excess of goods in relation to the order the Buyer may reject the excess goods by notice in writing to the Supplier and the following provisions shall apply: 8.5.1 the Supplier shall collect the excess goods from the Buyer at the Supplier’s expense; 8.5.2 during the period between delivery of the goods and collection by the Supplier, the Buyer shall not be liable for any loss or damage caused to the excess goods; 8.5.3 no sum shall be due to the Supplier for the excess goods and in the event that sums are paid to the Supplier for the excess goods, the Supplier shall repay such sums to the Buyer immediately. 8.6 The Buyer may accept excess goods by notifying the Supplier of such acceptance and the price of the excess goods shall be payable by the Buyer. 8.7 The Supplier shall repair or replace free of charge, goods damaged or lost in transit upon receiving notice to that effect from the Buyer. 8.8 The Buyer’s signature on any delivery note of the Supplier is evidence of the number of packages received only and not evidence of the correct quantity of goods received or that the goods are in a good condition or of the correct quality.
Identification of Goods Identification of the goods shall not be deemed to have been made until both Buyer and Seller have agreed that the goods in question are to be appropriate to the performance of this Agreement.
Account Histories The Transfer Agent may receive any fees reasonably related to the cost incurred by the Transfer Agent to prepare, at the request of a shareholder, an account history or provide other research information for any year(s) prior to the calendar year in which the request is made by the shareholder.
MEASUREMENT AND VERIFICATION The goal of this task is to report the benefits resulting from this project. • Enter into agreement with M&V subcontractor per Task 1.9 • Coordinate site visits with the M&V subcontractor at the demonstration site • Develop M&V protocol for pre-installation measurement and calculations following Section II.B.2 of the grant solicitation manual3: o Electric, natural gas and/or other fossil fuel consumption and greenhouse gas emissions (use appropriate emissions factor from Attachment 8 of the grant solicitation manual) of the equipment/process/system(s)/sub-system(s) that are be upgraded and/or replaced and/or modified; and o If necessary, ensure installation of sub-metering equipment and data loggers for pre/post data analysis. • Prepare and provide a detailed Measurement and Verification Plan to include but not be limited to: o A description of the monitoring equipment and instrumentation which will be used; o A description of the key input parameters and output metrics which will be measured; o A description of the M&V protocol and analysis methods to be employed; and o A description of the independent, third-party measurement and verification services to be employed. • Perform three months (or shorter period as approved in writing by the CAM) of pre- installation measurements and calculations, based on the M&V protocol for pre-install • Prepare and provide a Pre-Installation Measurement and Verification Findings Report which includes M&V protocol, pre-install measurements (and calculations), analysis, and results performed in this task. • Develop M&V protocol for post-installation measurements (and calculations) of: o Electric, natural gas and/or other fossil fuel consumption and greenhouse gas emissions (use appropriate emissions factor from Attachment 8 of the grant solicitation manual) of the equipment/process/system(s)/sub-system(s) that will be upgraded and/or replaced and/or modified Perform 12 months (or shorter period as approved in writing by the CAM) of post- installation measurements based on M&V protocol for post-installation. • Provide a summary of post-installation M&V progress in Progress Report(s) (see subtask 1.5) which shall include but not be limited to: o A narrative on operational highlights from the reporting period, including any stoppages in operation and why; and o A summary of M&V findings from the reporting period. • Analyze post-installation electrical, natural gas and/or other fossil fuel consumption and greenhouse gas emissions. • Prepare and provide a Post-Installation Measurement and Verification Findings Report that includes M&V protocol, pre and post install measurements and calculations, analysis, and results performed in this task. Results should at a minimum report on the reduction of electricity, natural gas and/or other fossil fuel usage and reductions of greenhouse gas emissions that directly result from this project.
Description of Goods or Services and Additional Terms and Conditions The Contractor shall perform as set forth in Exhibit A. For purposes of this Contract, to perform and the performance in Exhibit A is referred to as “Perform” and the “Performance.”
Classification of Goods The classification of goods in trade between the Parties shall be that set out in each Party's respective tariff nomenclature in conformity with the 2012 Harmonised System based on the International Convention on the Harmonised Commodity Description and Coding System of 1983 (HS) and subsequent amendments thereto.