Removal Procedure. Subject to:
(a) the Executive Committee having given the Settlement System Administrator a Remediable Removal Notice, and either the Settlement System Administrator having been unwilling or unable to remedy the failure within 30 days from the date of receipt of the Remediable Removal Notice (or such longer period as may be permitted under subsection 17.1) or, as the case may be, within the period provided in the timetable agreed with the Executive Committee for the remedy of such failure; or
(b) the Executive Committee having given the Settlement System Administrator an Irremediable Removal Notice, ESIS may be removed as Settlement System Administrator where:
(i) a resolution of the Pool Members in general meeting resolving to remove ESIS as Settlement System Administrator has been passed by either:
(a) Pool Members holding not less than 80 per cent. of the Total Votes of Pool Members who are entitled to vote in person or by proxy at a general meeting of Pool Members or deemed effective pursuant to Clause 13.5; or
(b) Pool Members holding less than 80 per cent. of the Total Votes of Pool Members who are entitled to vote in person or by proxy at a general meeting of Pool Members, but only where there is no more than one dissentient Pool Member;
(ii) the Director has given his prior written consent in the light of the resolution passed in accordance with sub-paragraph (i) above; and
(iii) the Executive Committee has given the Settlement System Administrator after such resolution has been passed or deemed effective (which the Executive Committee shall promptly do) 12 months' notice in writing (in this Section 17, the "Removal Notice") of such removal to take effect on the date specified in the Removal Notice (in this Section 17, the "Termination Date") and, subject to Section 20, the appointment of ESIS as Settlement System Administrator shall terminate on the Termination Date.
Removal Procedure. 1. Remove the two screw covers (3) on the lower flip (1) by piercing them at the centre with tweezers and by acting as a lever.
2. On the back flip cover (1), unscrew the two attachment screws (4) .
3. Separate the four fixing stop pins (5) on the back flip side (2) to release it from the front flip cover (1)
4. Remove the front flip cover (2)
Removal Procedure. When such removal takes place, the Union or its representatives shall direct the workmen on such job to carefully put away all tools, materials, equipment or any other property of the Employer in a safe manner. The Union will be financially responsible for any loss to the Employer for neglect in carrying out this provision, but only when a safe place is provided for these by the Employer.
Removal Procedure. 1. On the back cover (1), unscrew the two attachment screws (2) .
2. Lift delicately the back cover (1) up by pressing on the pins (3) then, insert a flat screwdriver into the nicks (4) an press inside the back cover (1) while keeping separated the two covers to release the stop pins (5)
3. Press on the stop pins (6) with a flat screwdriver to release the back cover (1)
4. Remove rear cover (1)
Removal Procedure. 1. Lift equipped electronic board up to liberate it of the front cover (1)
2. Remove the keypad (2), the control key (3) and the side decors (4) from the front cover (1).
Removal Procedure. 1. Unsolder the microphone (2) from the equipped electronic board (1)
2. Remove the microphone (2)
Removal Procedure. Subject to:-
(a) the Executive Committee having given the Settlement System Administrator a Remediable Removal Notice, and either the Settlement System Administrator having been unwilling or unable to remedy the failure within 30 days from the date of receipt of the Remediable Removal Notice (or such longer period as may be permitted under sub-section 17.1) or, as the case may be, within the period provided in the timetable agreed with the Executive Committee for the remedy of such failure; or
(b) the Executive Committee having given the Settlement System Administrator an Irremediable Removal Notice, ESIS may be removed as Settlement System Administrator where:-
(i) a resolution of the Pool Members in general meeting resolving to remove ESIS as Settlement System Administrator has been passed by either:-
Removal Procedure. 1. Turn the equipped electronic board (1) round ( at 90°maximum ) to release it from the front cover (2)
2. Open Zif connector lock (3) by sliding lock up
3. Remove delicately the flex PCB (4).
4. Remove the equipped electronic board (1)
Removal Procedure. Unscrew the antenna (1) of the back cover (2)
Removal Procedure. 1. Open front access door.
2. Remove door cover with 3 / 8" open end wrench.
3. On power door units, disconnect the cable at- tached to the bottom of the door.
4. Place a block approximately 1 / 2" high under the door counterweight, such that when the door is placed in the full up position there is some slack in the counterweight cables.
5. Locate door lock pins and "install both in door with door in full up position. With the spacer under the counterweight some additional effort will be needed to raise the door.
6. Remove the screws attaching the counterweight cables to the door bracket. With a pencil, mark screw locations.
7. Using a 3 / 4" open end wrench, remove the two door guide tubes.
8. Support door and remove the door lock pins with the other hand. The door can now be lowered. Once lowered past the bottom of the end frame, the door can be removed.
