Robustness Rules for Standard. Devices (Exhibit B of the Agreement);
Robustness Rules for Standard Sample Clauses
Related to Robustness Rules for Standard
Contractor Standards Contractor shall comply with Contractor Standards provisions codified in the SDMC. Contractor understands and agrees that violation of Contractor Standards may be considered a material breach of the Contract and may result in Contract termination, debarment, and other sanctions.
Compliance with Applicable Laws, Rules and Regulations The Dealer Manager represents to the Company that (a) it is a member of FINRA in good standing, and (b) it and its employees and representatives who will perform services hereunder have all required licenses and registrations to act under this Agreement. With respect to its participation and the participation by each Participating Dealer in the offer and sale of the Offered Shares (including, without limitation, any resales and transfers of Offered Shares), the Dealer Manager agrees, and, by virtue of entering into the Participating Dealer Agreement, each Participating Dealer shall have agreed, to comply with any applicable requirements of the Securities Act and the Exchange Act, applicable state securities or blue sky laws, and, specifically including, but not in any way limited to, NASD Conduct Rules 2340 and 2420, and FINRA Conduct Rules 2310, 5130 and 5141.
Compliance with Laws, Rules and Regulations a. Assurances. The Contractor agrees that all activity pursuant to this Contract will be in accordance with all applicable current federal, state and local laws, rules, and regulations, including but not limited to the Public Records Act (chapter 42.56 RCW), the Freedom of Information Act (5 U.S.C. 522) and the Records Retention Act (chapter 40.14 RCW).
Compliance with Rules and Policies The Executive shall perform all services in accordance with the lawful policies, procedures and rules established by the Company and the Board. In addition, the Executive shall comply with all laws, rules and regulations that are generally applicable to the Company or its subsidiaries and their respective employees, directors and officers.
Service Level Standards In addition to all other requirements in this Agreement, and in accordance with the Best Claims Practices & Estimating Guidelines, Vendor shall use reasonable and good faith efforts to meet the Service Level Standards set forth below.
Fitness for Duty When question exists related to appropriate leave administration or work safety to individuals, co-workers or others, the EMPLOYER may require employees to undergo a medical evaluation that will enable the EMPLOYER to determine the employee’s fitness for performance of his/her duties. When the EMPLOYER requires an evaluation or report from a medical authority, either the employee’s personal or treating authority or the medical authority of the EMPLOYER’s selection, the EMPLOYER shall: A. Pay the fee charged for such evaluation or report if such is not covered through the health insurance program made available to employees by the EMPLOYER, and B. Compensate the employee at his/her BASE PAY RATE for regularly scheduled work time the employee was unable to work due to obtaining the evaluation if the evaluation result is that the employee is found fully fit to perform his/her work duties and responsibilities.
Standards for Determining Commercial Reasonableness Borrower and Silicon agree that a sale or other disposition (collectively, "sale") of any Collateral which complies with the following standards will conclusively be deemed to be commercially reasonable: (i) Notice of the sale is given to Borrower at least seven days prior to the sale, and, in the case of a public sale, notice of the sale is published at least seven days before the sale in a newspaper of general circulation in the county where the sale is to be conducted; (ii) Notice of the sale describes the collateral in general, non-specific terms; (iii) The sale is conducted at a place designated by Silicon, with or without the Collateral being present; (iv) The sale commences at any time between 8:00 a.m. and 6:00 p.m; (v) Payment of the purchase price in cash or by cashier's check or wire transfer is required; (vi) With respect to any sale of any of the Collateral, Silicon may (but is not obligated to) direct any prospective purchaser to ascertain directly from Borrower any and all information concerning the same. Silicon shall be free to employ other methods of noticing and selling the Collateral, in its discretion, if they are commercially reasonable.
OMB Standards Unless specified otherwise within this agreement, the Subrecipient shall procure all materials, property, or services in accordance with the requirements of 24 CFR 84.40−48.
Applicable Standards The requirements and guidelines of NERC, the Applicable Regional Entity, and the Control Area in which the Customer Facility is electrically located; the PJM Manuals; and Applicable Technical Requirements and Standards.
Policies, Guidelines, Directives and Standards Either the Funder or the Ministry will give the HSP Notice of any amendments to the manuals, guidelines or policies identified in Schedule C. An amendment will be effective in accordance with the terms of the amendment. By signing a copy of this Agreement the HSP acknowledges that it has a copy of the documents identified in Schedule C.
