Secondary System 2D Modeling Sample Clauses

Secondary System 2D Modeling. The following systems, general locations, and lengths will be studied using 2D* Dynamic Modeling as specified below. ⮚ BON_0432 — Approximately 4,400 feet of neighborhood drainage system with 16 catchments and 30 links. ⮚ BON_0415 — Approximately 14,700 feet of neighborhood drainage system with 64 catchments and 100 links. ⮚ BON_0403/0404/0426 - Approximately 25,000 feet of neighborhood drainage system with 64 catchments and 170 links. ⮚ BON_0434/0407 - Approximately 10,000 feet of neighborhood drainage system with 36 catchments and 75 links. ⮚ BON_0409/0410 - Approximately 15,000 feet of neighborhood drainage system with 50 catchments and 100 links. ⮚ BON_0426/0601 - Approximately 4,500 feet of neighborhood drainage system with 35 catchments and 60 links. ⮚ BON_0704/0705/0707 - Approximately 25,000 feet of neighborhood drainage system with 105 catchments and 240 links. ⮚ BON_1104 - Approximately 9,000 feet of neighborhood drainage system with 30 catchments and 60 links. i. Develop a system-specific modeling approach (inlets grouped or modeled individually, trunkline only or full storm drain network, etc.) and provide justification for the approach. PgM will review the approach before work is underway. ii. Consultant will conduct a desktop assessment of the field survey data collected as described under Task 2.1 above. In addition, consultant will conduct limited site visits to field check inlets and outlet pipes within the system. If discrepancies and/or errors are noted in the survey data provided, Consultant will notify the PgM of the apparent error and request updated survey data be provided. No provision has been made in this proposal for conducting additional field survey services. iii. Develop a new dynamic model for each system listed above based on recently collected infrastructure data, GIS, as-built record drawings, and LIDAR data. a. All hydrograph routing will be performed within the dynamic modeling software package. iv. Where the system is surcharged and the overflow path is known and multidirectional, add 2D Zones to represent the overland flow. Final 2D Zone extents should fully encompass the highest level of flooding produced by the hydrology. 2D Zones that spread shallow flow across a known floodplain may be terminated with a boundary condition within 10 feet or 2 2D elements of the receiving stream bankline. v. Develop flow loading diagram for system. vi. Determine the existing condition water surface elevations within the system study ...
AutoNDA by SimpleDocs

Related to Secondary System 2D Modeling

  • Secondary Systems The Developer and Connecting Transmission Owner shall each cooperate with the other in the inspection, maintenance, and testing of control or power circuits that operate below 600 volts, AC or DC, including, but not limited to, any hardware, control or protective devices, cables, conductors, electric raceways, secondary equipment panels, transducers, batteries, chargers, and voltage and current transformers that directly affect the operation of Developer or Connecting Transmission Owner’s facilities and equipment which may reasonably be expected to impact the other Party. The Developer and Connecting Transmission Owner shall each provide advance notice to the other Party, and to NYISO, before undertaking any work on such circuits, especially on electrical circuits involving circuit breaker trip and close contacts, current transformers, or potential transformers.

  • System Logging The system must maintain an automated audit trail which can 20 identify the user or system process which initiates a request for PHI COUNTY discloses to 21 CONTRACTOR or CONTRACTOR creates, receives, maintains, or transmits on behalf of COUNTY, 22 or which alters such PHI. The audit trail must be date and time stamped, must log both successful and 23 failed accesses, must be read only, and must be restricted to authorized users. If such PHI is stored in a 24 database, database logging functionality must be enabled. Audit trail data must be archived for at least 3 25 years after occurrence.

  • Evaluation, Testing, and Monitoring 1. The System Agency may review, test, evaluate and monitor Grantee’s Products and services, as well as associated documentation and technical support for compliance with the Accessibility Standards. Review, testing, evaluation and monitoring may be conducted before and after the award of a contract. Testing and monitoring may include user acceptance testing. Neither the review, testing (including acceptance testing), evaluation or monitoring of any Product or service, nor the absence of review, testing, evaluation or monitoring, will result in a waiver of the State’s right to contest the Grantee’s assertion of compliance with the Accessibility Standards. 2. Grantee agrees to cooperate fully and provide the System Agency and its representatives timely access to Products, records, and other items and information needed to conduct such review, evaluation, testing, and monitoring.

  • HIV/AIDS Model Workplace Guidelines Grantee will: a. implement the System Agency’s policies based on the Human Immunodeficiency Virus/Acquired Immunodeficiency Syndrome (HIV/AIDS), AIDS Model Workplace Guidelines for Businesses at xxxx://xxx.xxxx.xxxxx.xx.xx/hivstd/policy/policies.shtm, State Agencies and State Grantees Policy No. 090.021. b. educate employees and clients concerning HIV and its related conditions, including AIDS, in accordance with the Texas. Health & Safety Code §§ 85.112-114.

  • Random Drug Testing All employees covered by this Agreement shall be subject to random drug testing in accordance with Appendix D.

  • Computer Equipment Recycling Program If this Contract is for the purchase or lease of computer equipment, then Contractor certifies that it is in compliance with Subchapter Y, Chapter 361 of the Texas Health and Safety Code related to the Computer Equipment Recycling Program and the Texas Commission on Environmental Quality rules in 30 TAC Chapter 328.

  • Synchronization, Commissioning and Commercial Operation 4.1.1 The Power Producer shall give at least fifteen (15) days written notice to the SLDC / ALDC / DISCOM as the case may be, of the date on which it intends to synchronize the Power Project to the Grid System. 4.1.2 Subject to Article 4.1.1, the Power Project may be synchronized by the Power Producer to the Grid System when it meets all the connection conditions prescribed in the Grid Code and otherwise meets all other Indian legal requirements for synchronization to the Grid System. 4.1.3 The synchronization equipment and all necessary arrangements / equipment including Remote Terminal Unit (RTU) for scheduling of power generated from the Project and transmission of data to the concerned authority as per applicable regulation shall be installed by the Power Producer at its generation facility of the Power Project at its own cost. The Power Producer shall synchronize its system with the Grid System only after the approval of GETCO / SLDC / ALDC and GEDA. 4.1.4 The Power Producer shall immediately after each synchronization / tripping of generator, inform the sub-station of the Grid System to which the Power Project is electrically connected in accordance with applicable Grid Code. 4.1.5 The Power Producer shall commission the Project within SCOD. 4.1.6 The Power Producer shall be required to obtain Developer and/ or Transfer Permission, Key Plan drawing etc, if required, from GEDA. In cases of conversion of land from Agricultural to Non-Agriculture, the commissioning shall be taken up by GEDA only upon submission of N.A. permission by the Power Producer. 4.1.7 The Power Producer shall be required to follow the Forecasting and Scheduling procedures as per the Regulations issued by Hon’ble GERC from time to time. It is to clarify that in terms of GERC (Forecasting, Scheduling, Deviation Settlement and Related Matters of Solar and Wind Generation Sources) Regulations, 2019 the procedures for Forecasting, Scheduling & Deviation Settlment are applicable to all solar generators having combined installed capacity above 1 MW connected to the State Grid / Substation including those connected via pooling stations.

  • Access Toll Connecting Trunk Group Architecture 9.2.1 If CSTC chooses to subtend a Verizon access Tandem, CSTC’s NPA/NXX must be assigned by CSTC to subtend the same Verizon access Tandem that a Verizon NPA/NXX serving the same Rate Center Area subtends as identified in the LERG. 9.2.2 CSTC shall establish Access Toll Connecting Trunks pursuant to applicable access Tariffs by which it will provide Switched Exchange Access Services to Interexchange Carriers to enable such Interexchange Carriers to originate and terminate traffic to and from CSTC’s Customers. 9.2.3 The Access Toll Connecting Trunks shall be two-way trunks. Such trunks shall connect the End Office CSTC utilizes to provide Telephone Exchange Service and Switched Exchange Access to its Customers in a given LATA to the access Tandem(s) Verizon utilizes to provide Exchange Access in such LATA. 9.2.4 Access Toll Connecting Trunks shall be used solely for the transmission and routing of Exchange Access to allow CSTC’s Customers to connect to or be connected to the interexchange trunks of any Interexchange Carrier which is connected to a Verizon access Tandem.

  • Network Interconnection Architecture Each Party will plan, design, construct and maintain the facilities within their respective systems as are necessary and proper for the provision of traffic covered by this Agreement. These facilities include but are not limited to, a sufficient number of trunks to the point of interconnection with the tandem company, and sufficient interoffice and interexchange facilities and trunks between its own central offices to adequately handle traffic between all central offices within the service areas at a P.01 grade of service or better. The provisioning and engineering of such services and facilities will comply with generally accepted industry methods and practices, and will observe the rules and regulations of the lawfully established tariffs applicable to the services provided.

  • Architecture The Private Improvements shall have architectural features, detailing, and design elements in accordance with the Project Schematic Drawings. All accessory screening walls or fences, if necessary, shall use similar primary material, color, and detailing as on the Private Improvements.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!