Short circuit Sample Clauses

Short circuit. At the start of the test all relevant main contactors for charging and discharging shall be closed to represent the active driving possible mode as well as the mode to enable external charging. If this cannot be completed in a single test, then two or more tests shall be conducted. For testing with a complete REESS or REESS subsystem(s), the positive and negative terminals of the Tested-Device shall be connected to each other to produce a short circuit. The connection used for this purpose shall have a resistance not exceeding 5 mΩ. For testing with a complete vehicle, the short circuit is applied through the breakout harness. The connection used for creating the short circuit (including the cabling) shall have a resistance not exceeding 5 mΩ. The short circuit condition shall be continued until the protection function operation of the REESS terminate the short circuit current is confirmed, or for at least one hour after the temperature measured on the casing of the Tested-Device has stabilised, such that the temperature gradient varies by a less than 4 °C through 2 hour.
Sample 1Sample 2Sample 3See All (6)
Short circuit. At the start of the test all relevant main contactors for charging and discharging shall be closed to represent the active driving possible mode as well as the mode to enable external charging. If this cannot be completed in a single test, then two or more tests shall be conducted. The positive and negative terminals of the tested-device shall be connected to each other to produce a short circuit. The connection used for this purpose shall have a resistance not exceeding 5 mΩ. The short circuit condition shall be continued until the operation of the REESS´s protection function to interrupt or limit the short circuit current is confirmed, or for at least one hour after the temperature measured on the casing of the tested-device has stabilised, such that the temperature gradient varies by a less than 4 °C through 1 hour.
Sample 1Sample 2Sample 3See All (6)
Short circuit. At the start … be conducted. For testing with a complete REESS or REESS subsystem(s), the positive and negative terminals of the Tested-Device shall be connected to each other to produce a short circuit. The connection … 5 mΩ. For testing with a complete vehicle, the short circuit is applied through the breakout harness. The connection used for creating the short circuit (including the cabling) shall have a resistance not exceeding 5 mΩ. The short circuit condition shall be continued until the protection function operation of the REESS terminate the short circuit current, or for at least 1 hour after the temperature measured on the casing of the Tested-Device has stabilised, such that the temperature gradient varies by a less than 4 °C through 2 hours.
Sample 1
Short circuit. The External Short Circuit trial is carried out in accordance with the procedure described in item 7.5 of Anatel Resolution No. 481. Part of the samples are stored at room temperature and another part at 55 ± 3°C.
Sample 1

Related to Short circuit

  • Assembly (a) The Contracting Parties shall have an Assembly. (b) Each Contracting Party shall be represented by one delegate who may be assisted by alternate delegates, advisors and experts. (c) The expenses of each delegation shall be borne by the Contracting Party that has appointed the delegation. The Assembly may ask WIPO to grant financial assistance to facilitate the participation of delegations of Contracting Parties that are regarded as developing countries in conformity with the established practice of the General Assembly of the United Nations or that are countries in transition to a market economy. (a) The Assembly shall deal with matters concerning the maintenance and development of this Treaty and the application and operation of this Treaty. (b) The Assembly shall perform the function allocated to it under Article 26(2) in respect of the admission of certain intergovernmental organizations to become party to this Treaty. (c) The Assembly shall decide the convocation of any diplomatic conference for the revision of this Treaty and give the necessary instructions to the Director General of WIPO for the preparation of such diplomatic conference. (a) Each Contracting Party that is a State shall have one vote and shall vote only in its own name. (b) Any Contracting Party that is an intergovernmental organization may participate in the vote, in place of its Member States, with a number of votes equal to the number of its Member States which are party to this Treaty. No such intergovernmental organization shall participate in the vote if any one of its Member States exercises its right to vote and vice versa. (4) The Assembly shall meet in ordinary session once every two years upon convocation by the Director General of WIPO. (5) The Assembly shall establish its own rules of procedure, including the convocation of extraordinary sessions, the requirements of a quorum and, subject to the provisions of this Treaty, the required majority for various kinds of decisions.

  • Fabrication Making up data or results and recording or reporting them.

  • Architecture The Private Improvements shall have architectural features, detailing, and design elements in accordance with the Project Schematic Drawings. All accessory screening walls or fences, if necessary, shall use similar primary material, color, and detailing as on the Private Improvements.

  • Evaluation Software If the Software is an evaluation version or is provided to You for evaluation purposes, then, unless otherwise approved in writing by an authorized representative of Licensor, Your license to use the Software is limited solely for internal evaluation purposes in non-production use and in accordance with the terms of the evaluation offering under which You received the Software, and expires 90 days from installation (or such other period as may be indicated within the Software). Upon expiration of the evaluation period, You must discontinue use of the Software, return to an original state any actions performed by the Software, and delete the Software entirely from Your system and You may not download the Software again unless approved in writing by an authorized representative of Licensor. The Software may contain an automatic disabling mechanism that prevents its use after a certain period of time. RESTRICTIONS

  • Short Description Post-Bachelor's

  • Embedded Software To the extent any goods contain Embedded Software (defined below) that is not Buyer’s Property, no title to such Embedded Software shall pass to Buyer, and Supplier shall grant Buyer, its customers and all other users a non-exclusive worldwide, irrevocable, perpetual, royalty-free right to use, load, install, execute, demonstrate, market, test, resell, sublicense and distribute such Embedded Software as an integral part of such goods or for servicing the goods (the “Buyer-Required License”). If such Embedded Software or any part thereof is owned by a third party, prior to delivery, Supplier shall obtain the Buyer-Required License from such third-party owner. “Embedded Software” means software necessary for operation of goods and embedded in and delivered as an integral part of goods.

  • Configuration The configuration for the Purchase Right Aircraft will be the Detail Specification for Model 767-3S2F aircraft at the revision level in effect at the time of the Supplemental Agreement. Such Detail Specification will be revised to include (i) changes required to obtain required regulatory certificates and (ii) other changes as mutually agreed upon by Boeing and Customer.

  • Interoperability To the extent required by applicable law, Cisco shall provide You with the interface information needed to achieve interoperability between the Software and another independently created program. Cisco will provide this interface information at Your written request after you pay Cisco’s licensing fees (if any). You will keep this information in strict confidence and strictly follow any applicable terms and conditions upon which Cisco makes such information available.