Specifications and Tests Sample Clauses

Specifications and Tests. 5.1. The vehicle shall undergo a test in accordance with Annex 4 to this Regulation. 5.1.1. The test will be carried out on the driver’s side unless asymmetric side structures, if any, are so different as to affect the performance in a side impact. In that case either of the alternatives in paragraph 5.1.1.1. or 5. 1.1.2. below may be used by agreement between the manufacturer and Type Approval Authority. 5.1.1.1. The manufacturer will provide the authority responsible for approval with information regarding the compatibility of performances in comparison with the driver’s side when the test is being carried out on that side. 5.1.1.2. The Type Approval Authority, if concerned as to the construction of the vehicle, will decide to have the test performed on the side opposite the driver, this being considered the least favourable.

Specifications and Tests. 5.1. The vehicle shall undergo a test in accordance with Annex 4 to this Regulation. 5.1.1. The test will be carried out on the driver’s side unless asymmetric side structures, if any, are so different as to affect the performance in a side impact. In that case either of the alternatives in paragraph 5.1.1.1. or 5.1.1.2. may be used by agreement between the manufacturer and test authority. 5.1.1.1. The manufacturer will provide the authority responsible for approval with information regarding the compatibility of performances in comparison with the driver’s side when the test is being carried out on that side. 1 The distinguish numbers of the Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev.2. 5.1.1.2. The Approval Authority, if concerned as to the construction of the vehicle, will decide to have the test performed on the side opposite the driver, this being considered the least favourable. 5.1.2. The Technical Service, after consultation with the manufacturer, may require the test to be carried out with the seat in a position other than the one indicated in paragraph 5.5.1. of Annex 4. This position shall be indicated in the test report2. 5.1.3. The result of this test shall be considered satisfactory if the conditions set out in paragraphs 5.2. and 5.3. below are satisfied. 5.2. Performance criteria

Specifications and Tests. Small volume manufacturers As an alternative to the requirements of this paragraph, vehicle manufacturers whose world-wide annual production is less than 10,000 units may obtain approval on the basis of the corresponding technical requirements specified in the table below.

Specifications and Tests. 5.1.1 Scope amended to include M2, M3, N2, N3, O3, O4 and N1 vehicles with twin wheels as well. Consideration of only vehicles fitted with single tyres removed since the amended regulation will apply to vehicles with single and twin tyres.

Specifications and Tests. 5.1. Protection against electrical shock These electrical safety requirements apply to high voltage buses under conditions where they are not connected to external high voltage power supplies. 5.1.1. Protection against direct contact 1.1.1. and 5. 1.1.2. These protections (solid insulator, barrier, enclosure, etc.) shall not be able to be opened, disassembled or removed without the use of tools. 1 1 for Germany, 2 for France, 3 for Italy, 4 for the Netherlands, 5 for Sweden, 6 for Belgium, 7 for Hungary, 8 for the Czech Republic, 9 for Spain, 10 for Serbia, 11 for the United Kingdom, 12 for Austria, 13 fxx Xxxxxxxxrg, 14 for Switzerland, 00 (xxxxxx), 00 xxx Xxxxay, 17 for Finland, 18 for Denmark, 19 for Romania, 20 for Poland, 21 for Portugal, 22 for the Russian Federation, 23 for Greece, 24 for Ireland, 25 fxx Xxxxxxx, 26 fxx Xxxxxxxx, 27 for Slovakia, 28 xxx Xxxxxxx, 29 for Estonia, 30 (xxxxxx), 00 xxx Xxxxxx xxx Xxxxxxxxxxx, 00 xxx Xxxxia, 33 (vacant), 34 for Bulgaria, 35 (Xxxxxxxxxx), 00 xxx Xxxxuania, 37 for Turkey, 38 (vacant), 39 for Azerbaijan, 40 for The former Yugoslav Republic of Macedonia, 41 (vacant), 42 for the European Union (Approvals are granted by its Member States using their respective ECE symbol), 43 for Japan, 44 (vacant), 45 for Australia, 46 for Ukraine, 47 fxx Xxxxx Xxrica, 48 for New Zealand, 49 for Cyprus, 50 for Malta, 51 for the Republic of Korea, 52 for Malaysia, 53 for Thailand, 54 and 55 (vacant), 56 for Montenegro, 57 (vacant) and 58 for Tunisia. Other numbers shall be assigned to other countries in the chronological order in which they ratify or accede to the Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts which can be Fitted and/or be Used on Wheeled Vehicles and the Conditions for Reciprocal Recognition of Approvals Granted on the Basis of these Prescriptions, and the numbers thus assigned shall be communicated by the Secretary- General of the United Nations to the Contracting Parties to the Agreement. 5.1.1.1. For protection of live parts inside the passenger compartment or luggage compartment, the protection degree IPXXD shall be provided. 5.1.1.2. For protection of live parts in areas other than the passenger compartment or luggage compartment, the protection degree IPXXB shall be satisfied. 5.1.1.3. Connectors Connectors (including vehicle inlet) are deemed to meet this requirement if: (a) They comply with 5.1.1.1. and 5.

Specifications and Tests. Note: As an alternative to the requirements of this paragraph, vehicle manufacturers whose world-wide annual production is less than 10,000 units may obtain approval on the basis of the corresponding technical requirements specified in: the California Code of Regulations, Title 13, Paragraphs 1960.1 (f) (2) or (g) (1) and (g) (2), 1960.1 (p) applicable to 1996 and later model-year vehicles, 1968.1, 1976 and 1975, applicable to 1995 and later model year light-duty vehicles (California Code of Regulations is published by Barclays Publishing).

Specifications and Tests. The Type Approval Authority shall inform the other Type Approval Authorities of Contracting Parties of the circumstances of each type approval granted under this paragraph. The emissions tests for roadworthiness purposes set out in Annex 5 shall still be required to obtain type approval with regard to emissions under this paragraph.

Specifications and Tests