Stamping, sealing and signing of the Sample Clauses

Stamping, sealing and signing of the certificate All separate sheets of the joint degree certificate will be either stamped or sealed individually by the two universities awarding the degree. In addition, each separate sheet will be signed by the following office holders in the four TEEME universities: • for degrees awarded by the University of Kent, the ViceEChancellor; • for degrees awarded by Freie Universität Berlin, the Xxxx of the relevant Faculty; • for degrees awarded by Universidade do Porto, the Xxxxxx of the University and the Academic Registrar; • for degrees awarded by Univerzita Karlova v Praze, the Xxxxxx of the University, or the ViceERector appointed by the Xxxxxx. The signatures of these office holders will be either added by hand or embedded electronically into the paper used for the certificate.
Sample 1
AutoNDA by SimpleDocs

Related to Stamping, sealing and signing of the

  • Format and Signing of Tender 19.1 The Tenderer shall prepare one original of the documents comprising the Tender as described in ITT 11 and clearly mark it “ORIGINAL.” Alternative Tenders, if permitted in accordance with ITT 12, shall be clearly marked “ALTERNATIVE.” In addition, the Tenderer shall submit copies of the Tender, in the number specified in the TDS and clearly mark them “COPY.” In the event of any discrepancy between the original and the copies, the original shall prevail.

  • Skidding and Yarding Methods of skid- ding or yarding specified for particular areas, if any, are indicated on Sale Area Map. Outside Clearcutting Units and construction clearings, insofar as ground conditions permit, products shall not be skidded against reserve trees or groups of reproduction and tractors shall be equipped with a winch to facilitate skidding. B6.421 Rigging. Insofar as practicable, needed rigging shall be slung on stumps or trees desig- nated for cutting.

  • DHS Seal, Logo, and Flags The Contractor shall not use the Department of Homeland Security (DHS) seal(s), logos, crests, or reproductions of flags or likeness of DHS agency officials without specific FEMA pre-approval.

  • Sealing and Marking of Bids 21.1 The bidder shall seal the original and each copy of the bid in separate envelopes duly marking the envelopes “ORIGINAL” and “COPY”. The envelopes shall then be sealed in an outer separate envelope.

  • Format and Signing of Bid 18.1 The Bidder shall prepare one original and one copy of the documents comprising the bid as described in Clause 12 of these Instructions to Bidders, bound with the volume containing the Form of Bid, and clearly marked “ORIGINAL” and “COPY” as appropriate. In the event of discrepancy between them, the original shall prevail.

  • FORMAT AND SIGNING OF BIDS 20.1 The bidder shall prepare one original of the documents comprising the bid as described in Clause 13 of these Instructions to Bidders, bound with the section containing the Form of Bid and Appendix to Bid, and clearly marked “ORIGINAL”. In addition, the bidder shall submit a replica copy of the bid clearly marked “COPY OF ORIGINAL”. However, in the event of discrepancy between them, the original shall prevail.

  • Sealing and Marking of Tenders 2.17.1 The Tenderer shall seal the original and each copy of the tender in separate envelopes, duly marking the envelopes as “ORIGINAL” and “COPY.” The envelopes shall then be sealed in an outer envelope.

  • Felling and Bucking Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. Purchaser may buck out cull material when necessary to produce pieces meeting Utilization Standards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net scale in percentage of gross scale, or based on the merchantability factor, whichever is stated in A2. If necessary to assess extent of defect, Purchaser shall make sample saw cuts or wedges. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting. B6.000 Xxxxx Xxxxxxx. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum heights set forth in A6, except that occasional stumps of greater heights are acceptable when Purchaser determines that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed, Purchaser shall re-cut high stumps so they will not exceed heights specified in A6 and shall dispose of severed portions in the same manner as other logging debris. The xxxxx heights shown in A6 were selected with the objective of maximum reasonable utilization of the timber, unless Sale Area Map shows special areas where xxxxx heights are lower for aesthetic, land treatment, or silvicultural rea- sons.

  • Authorized Signatories The parties each represent and warrant to the other that (1) the persons signing this lease are authorized signatories for the entities represented, and (2) no further approvals, actions or ratifications are needed for the full enforceability of this Lease against it; each party indemnifies and holds the other harmless against any breach of the foregoing representation and warranty.

  • Authorized Signature Your signature on the Account Card authorizes your account access. We will not be liable for refusing to honor any item or instruction if we believe the signature is not genuine. If you have authorized the use of a facsimile signature, we may honor any check or draft that appears to bear your facsimile signature even if it was made by an unauthorized person. You authorize us to honor transactions initiated by a third person to whom you have given your account number even if you do not authorize a particular transaction.

Time is Money Join Law Insider Premium to draft better contracts faster.