Contractor Work Hours and Safety Standards Contractor shall ensure compliance with all safety and hourly requirements for employees, in accordance with federal, state, and County safety and health regulations and laws.
CONTRACT WORK HOURS AND SAFETY STANDARDS As per the Contract Work Hours and Safety Standards Act (40 U.S.C. 3701-3708), where applicable, all Customer Purchase Orders in excess of ,000 that involve the employment of mechanics or laborers must include a provision for compliance with 40 U.S.C. 3702 and 3704, as supplemented by Department of Labor regulations (29 CFR Part 5). Under 40 U.S.C. 3702 of the Act, each contractor must be required to compute the wages of every mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work week is permissible provided that the worker is compensated at a rate of not less than one and a half times the basic rate of pay for all hours worked in excess of 40 hours in the work week. The requirements of 40 U.S.C. 3704 are applicable to construction work and provide that no laborer or mechanic must be required to work in surroundings or under working conditions which are unsanitary, hazardous or dangerous. These requirements do not apply to the purchases of supplies or materials or articles ordinarily available on the open market, or contracts for transportation or transmission of intelligence.
Technical Safeguards 1. USAC and the Department will process the data matched and any data created by the match under the immediate supervision and control of authorized personnel to protect the confidentiality of the data, so unauthorized persons cannot retrieve any data by computer, remote terminal, or other means.
Safety Orientation All employees shall be certified in Safety Orientation. Safety Orientation shall consist of three parts: PART 1 - the CODC Interactive Rights and Responsibilities course; PART 2 - the XXXX course or equivalent, and PART 3 - Employer or Owner Project Specific Training. It is the responsibility of each employee to hold current certification and maintain certification in part 1 and Part 2. The Employer or Owner shall provide to each Employee before commencing work with PART 3 - Employer or Owner Project Specific Training. Each Employee shall be on the payroll and paid while receiving PART 3 training. As a condition of employment it is the sole responsibility of each and every employee to obtain, hold and maintain all current certification(s) in any and all legislated safety training requirements (i.e. WHMIS, Fall Arrest, etc.) that are trade specific. Supporting documentation of all legislated training must be provided by the employee to the Union prior to dispatch and to the employer upon hire and may be further requested by the employer at any time during the duration of their employment. Prior to the expiration of any certification, the Employer will notify the Employee of the pending expiration and give the Employee reasonable time to renew their certification. Further, prior to arriving at site, employees shall hold current qualification(s) for the specific tasks and equipment identified in the dispatch request. If the employee has to be trained after dispatch, all costs borne by the Employer shall be reimbursed by the Training Fund. The CODC Harassment Policy and Procedures, including the provisions regarding General Harassment and as amended from time to time shall be the minimum standard of this Agreement.
Technical Specifications The Technical Specifications furnished on the CD are intended to establish the standards for quality, performance and technical requirements for all labor, workmanship, material, methods and equipment necessary to complete the Work. When specifications and drawings are provided or referenced by the County, these are to be considered part of the Scope of Work, and to be specifically documented in the Detailed Scope of Work. For convenience, the County supplied specifications, if any, and the Technical Specifications furnished on the CD.
Technical Standards Applicable to a Wind Generating Plant i. Low Voltage Ride-Through (LVRT) Capability A wind generating plant shall be able to remain online during voltage disturbances up to the time periods and associated voltage levels set forth in the standard below. The LVRT standard provides for a transition period standard and a post-transition period standard.
Health and Safety Requirements The Contractor and his subcontractors ensure at all times compliance with safety regulations imposed by any Act of Parliament, ordinance or any regulation or by¬law of any local or statutory authority. Occupational Health and Safety Act (Act of 1993-Section 37) The Contractor shall comply with: The Occupational Health and Safety Xxx, 0000, and all Regulations made there under; All Eskom Safety and Operating Procedures listed in this Works Information. The Contractor acknowledges that it is fully aware of the requirements of all the above and undertakes to employ only people who have been duly authorised in terms thereof and who have received sufficient training to ensure that they can comply therewith. The Contractor undertakes not to do, or not to allow anything to be done which will contravene any of the provisions of the Act, Regulations or Safety and Operating Procedures. The Contractor shall appoint a person who will liaise with the Eskom Safety Officer responsible for the premises relevant to this contract. The person so appointed shall, on request: Supply the Eskom Safety Officer with copies of minutes of all Health and Safety Committee meetings, whenever he is required to do so; Supply the Eskom Safety Officer with copies of all appointments in respect of employees employed on this contract, in terms of the Act and Regulations and shall advise the Eskom Safety Officer of any changes thereto. Eskom may, at any stage during the currency of this agreement, be entitled to: Do safety audits at the Contractor’s premises, its work-places and on its employees; Refuse any employee, sub-contractor or agent of the Contractor access to its premises if such person has been found to commit any unlawful act or any unsafe working practice or is found to be not authorised or qualified in terms of the Act;
TECHNICAL TASKS Products that require a draft version are indicated by marking “(draft and final)” after the product name in the “Products” section of the task/subtask. If “(draft and final)” does not appear after the product name, only a final version of the product is required. Subtask 1.1 (Products) describes the procedure for submitting products to the CAM.
Information Technology Enterprise Architecture Requirements If this Contract involves information technology-related products or services, the Contractor agrees that all such products or services are compatible with any of the technology standards found at xxxxx://xxx.xx.xxx/iot/2394.htm that are applicable, including the assistive technology standard. The State may terminate this Contract for default if the terms of this paragraph are breached.
Information Technology Accessibility Standards Any information technology related products or services purchased, used or maintained through this Grant must be compatible with the principles and goals contained in the Electronic and Information Technology Accessibility Standards adopted by the Architectural and Transportation Barriers Compliance Board under Section 508 of the federal Rehabilitation Act of 1973 (29 U.S.C. §794d), as amended. The federal Electronic and Information Technology Accessibility Standards can be found at: xxxx://xxx.xxxxxx-xxxxx.xxx/508.htm.
