Common use of TECHNICAL TASKS Clause in Contracts

TECHNICAL TASKS. The purpose of this task is successful procurement and installation of all project components identified in this Agreement. Solar photovoltaic (PV) Wind turbine Battery Energy Storage Pump replacement (conversion of fossil fuel pump to electric pump) Electric Vehicle Charging Infrastructure System 1 Project Detail a. Renewable Energy System Description of where equipment will be installed on the property (For example: northeast corner by barn): Solar array will be a ground mount system installed in an open area and on bare ground on APN 000- 000-000 near the farm’s Red Barn Maintenance Facility, located adjacent to existing electric meters. For Solar PV, please identify the surface of installation: Rooftop If so, is the rooftop on an existing building? Yes No b. Parking lot (can be unpaved). If so, is it an existing parking lot? Yes No Ground-mounted or Floating (Solar Panels mounted on pontoons and floating on irrigation pond). Other: Electricity produced will be used to power (For example: greenhouse; irrigation pumps; electric vehicle charging): Electricity produced will be used to charge two zero-emission off-road equipment and mobile storage used for crop spraying from February through November and for year-round mowing for the farm’s almond tree crop. Rated Capacity of system: [ 67.2 ] kW General Description of Equipment (please include information such as number of arrays or turbines): The solar array will consist of 192 350-watt solar modules mounted in a ground field for a total nameplate capacity of 67.2 kW. Expected Make and Model of Equipment to be Installed (include modules and inverter): The brand of solar modules will be either Hanwha Q.cells or LG, purchased from a California vendor, and will be standard 72-cell, 350-watt modules. As an off-grid facility, it will not require an inverter or grid connection. The mounting system will be a commercial ground mount racking system from either Unirac or RBI Solar and will be determined at the start of the Project. Expected Contractor(s), if known (include Contractor State License Board (CSLB) license number): XxXxxxxxx Corporation, CSLB #941211, will provide the license for the initial building permit application and will subcontract a licensed California solar installer for construction of the equipment prior to installation. Paired Power, Inc. Battery Energy Storage Description of where equipment will be installed on the property and the renewable energy source serving the charger (For example: located with solar system installed at northeast corner by greenhouse): The battery energy storage will be contained in a 297kWh Mobile Power Station (MPS) located at the Xxxxxx Xxxxx Farms Red Barn Facility, as described above. The battery energy storage will be a mobile system on wheels that requires no ground-based installation. Battery will be used for (For example, provide back up for grid outages; to regularly shift or extend hours of use for the installed solar energy system): The battery storage will be used to power a 252kWh MPS; the MPS will be used primarily for spraying and mowing of the 3,600 acres of almond trees at Xxxxxx Xxxxx Farms; it may also be used as back-up power, as needed. XXXXXX Mobile Power Station (MPS) with BMW second-life lithium-ion battery modules with a total rated capacity of 297kWh. Expected Contractor(s), if known (include CSLB license number): XxXxxxxxx Corporation, CSLB #941211. The MPS used for energy storage will be provided by XX Xxxxxx, LLC.

TECHNICAL TASKS. The purpose of this task is successful procurement and installation of all project components identified in this Agreement. Solar photovoltaic (PV) Wind turbine Battery Energy Storage Pump replacement (conversion of fossil fuel pump to electric pump) Electric Vehicle Charging Infrastructure System 1 Project Detail a. Renewable Energy System (required) Description of where equipment will be installed on the property (For exampleproperty: northeast corner by barn): Solar The array will be a ground mount system installed located on the south side of the two shops in an open area and on bare ground on APN 000- 000-000 near the farm’s Red Barn Maintenance Facilitymiddle of the property located at 0000 Xxxxxx Xxxxxxx, located adjacent to existing electric metersXxxx Xxxx, XX. For Solar PV, please identify the surface of installation: Rooftop If so, is the rooftop on an existing building? Yes No b. Parking lot (can be unpaved). If so, is it an existing parking lot? Yes No Ground-mounted or Floating (Solar Panels mounted on pontoons and floating on irrigation pond). Other: Electricity produced will be used to power serve (For example: greenhouse; irrigation pumps; electric vehicle charging): Electricity produced will be used to charge two zero-emission off-road equipment and mobile storage used for crop spraying from February through November and for year-round mowing for the farm’s almond tree crop. 2 Irrigation Pumps, Shop, Walnut huller & dryer, Office building Rated Capacity of system: [ 67.2 [147.55] kW General Description of Equipment (please include information such as number of arrays or turbines): The solar array will consist of 192 350-watt solar modules Two roof mounted in a ground field arrays on one building with room for a total nameplate capacity walk way and the remaining modules on the longer of 67.2 kW. the two buildings. Expected Make and Model of Equipment to be Installed (include modules and inverter): The brand of solar modules will be either Modules: 454 Hanwha Q.cells or LG, purchased from a California vendor, and will be standard 72Q-cell, 350Cells DUO-watt modules. As an off-grid facility, it will not require an inverter or grid connection. The mounting system will be a commercial ground mount racking system from either Unirac or RBI G5 325 Inverter: Solar and will be determined at the start of the Project. Expected Contractor(s), if known (include Contractor State License Board (CSLB) license number): XxXxxxxxx Corporation, CSLB #941211, will provide the license for the initial building permit application and will subcontract a licensed California solar installer for construction of the equipment prior to installation. Paired Power, Inc. Battery Energy Storage Description of where equipment will be installed on the property and the renewable energy source serving the charger (For example: located with solar system installed at northeast corner by greenhouse): The battery energy storage will be contained in a 297kWh Mobile Power Station (MPS) located at the Xxxxxx Xxxxx Farms Red Barn Facility, as described above. The battery energy storage will be a mobile system on wheels that requires no ground-based installation. Battery will be used for (For example, provide back up for grid outages; to regularly shift or extend hours of use for the installed solar energy system): The battery storage will be used to power a 252kWh MPS; the MPS will be used primarily for spraying and mowing of the 3,600 acres of almond trees at Xxxxxx Xxxxx Farms; it may also be used as back-up power, as needed. XXXXXX Mobile Power Station (MPS) with BMW second-life lithium-ion battery modules with a total rated capacity of 297kWh. Edge Technologies SE25K Expected Contractor(s), if known (include CSLB license number): XxXxxxxxx Corporation, CSLB #941211. The MPS used for energy storage will be provided by XX Xxxxxx, Sunfinity Solar CA LLC.: CSLB# 1013931

TECHNICAL TASKS. The purpose of this task is successful procurement and installation of all project components identified in this Agreement. Solar photovoltaic (PV) Wind turbine Battery Energy Storage Pump replacement (conversion of fossil fuel pump to electric pump) Electric Vehicle Charging Infrastructure System 1 Project Detail a. Renewable Energy System Description of where equipment will be installed on the property (For example: northeast corner by barn): Solar array The solar system will be a ground mount system installed in an open area and on bare ground on APN 000- 000-000 located southeast of the barn located near the farm’s Red Barn Maintenance Facilitycenter of the parcel at 0000 Xxx Xxxxx Xx xx Xxxxxxx, located adjacent to existing electric metersXX. For Solar PV, please identify the surface of installation: Rooftop If so, is the rooftop on an existing building? Yes No b. Parking lot (can be unpaved). If so, is it an existing parking lot? Yes No Ground-mounted or Floating (Solar Panels mounted on pontoons and floating on irrigation pond). Other: Electricity produced will be used to power serve (For example: greenhouse; irrigation pumps; electric vehicle charging): Electricity produced will be used to charge two zeroIrrigation pumps and electric vehicle charging Irrigation pumps, on-emission off-road equipment site cooling, and mobile storage used for crop spraying from February through November and for year-round mowing for the farm’s almond tree cropelectric vehicle charging station. Rated Capacity of system: [ 67.2 [170.4] kW General Description of Equipment (please include information such as number of arrays or turbines): Nine ground-mounted solar arrays configured two panels high in portrait will support 480 solar panels and three inverters. The solar array will consist approximate footprint of 192 350-watt solar modules mounted in a ground field for a total nameplate capacity of 67.2 kW. the system is 226 ft x 101 ft. Expected Make and Model of Equipment to be Installed (include modules and inverter): The brand of solar modules will be either Hanwha Q.cells or LGSeraphim, purchased from a California vendor, and will be standard 72SRP-355-cell, 3506MA-watt HV (355W) modules. As an off-grid facility, it will not require an ; Solectria PVI 50TL inverter or grid connection. The mounting system will be a commercial ground mount racking system from either Unirac or RBI Solar and will be determined at the start of the Project. Expected Contractor(s), if known (include Contractor State License Board (CSLB) CSLB license number): XxXxxxxxx Corporation, CSLB #941211, will provide the license for the initial building permit application and will subcontract a licensed California solar installer for construction of the equipment prior to installation. Paired PowerXxxxxxxx’x Energy, Inc. Battery Energy Storage CSLB # 999665 b. Electric Vehicle Charger Description of where equipment will be installed on the property and the renewable energy source serving the charger (For example: located with solar system installed at northeast corner by greenhouse): The battery energy storage charging station will be contained located in a 297kWh Mobile Power Station (MPS) located at the Xxxxxx Xxxxx Farms Red Barn Facility, as described aboveemployee parking lot west of the barn. The battery energy storage charging station will be a mobile system on wheels that requires no ground-based installationserved by the 170.4 KW solar system. Battery will be used for (For example, provide back up for grid outages; to regularly shift or extend hours of use for the installed solar energy system): The battery storage Charger will be used to power a 252kWh MPS; the MPS will be used primarily for spraying serve (For example small car, off-road vehicles forklift, etc.): Employee and mowing of the 3,600 acres of almond trees at Xxxxxx Xxxxx Farms; it may also be used as back-up powerfarmer owned small cars, as neededwell as those of visitors. XXXXXX Mobile Power Station XXXX receives over 1,000 visitors per year. Is/are the vehicle(s) referenced above used for the agricultural operation specified in the application? Yes No PowerCharge Pro Series, Level 2, 7.2 KW, 30 Amp, Dual Port (MPSP20DP) with BMW second-life lithium-ion battery modules with a total rated capacity of 297kWh. Expected Contractor(s), if known (include CSLB license number): XxXxxxxxx CorporationXxxxxxxx’x Energy, Inc. CSLB #941211. The MPS used for energy storage will be provided by XX Xxxxxx, LLC.# 999665

TECHNICAL TASKS. The purpose of this task is successful procurement and installation of all project components identified in this Agreement. Solar photovoltaic (PV) Wind turbine Battery Energy Storage Pump replacement (conversion of fossil fuel pump to electric pump) Electric Vehicle Charging Infrastructure System 1 Project Detail a. Renewable Energy System Description of where equipment will be installed on the property (For example: northeast corner by barn): Solar array will be a ground mount system installed in an open area and on bare ground on APN 000- Project APN: 000-000 near 000-000. Northwest side of the farm’s Red Barn Maintenance Facility, located adjacent to existing electric metersproperty on the Roundabout made by the access roads. For Solar PV, please identify the surface of installation: Rooftop If so, is the rooftop on an existing building? Yes No b. Parking lot (can be unpaved). If so, is it an existing parking lot? Yes No Ground-mounted or Floating (Solar Panels mounted on pontoons and floating on irrigation pond). Other: Electricity produced will be used to power (For example: greenhouse; irrigation pumps; electric vehicle charging): Electricity produced will be used to charge two zero-emission off-road equipment 25 HP Well Irrigation pump and mobile storage used for crop spraying from February through November and for year-round mowing for the farm’s almond tree cropEV 48VDC charger. Rated Capacity of system: [ 67.2 [_27_] kW General Description of Equipment (please include information such as number of arrays or turbines): VariSun 27 kW Solar Pumping Ballasted Ground Mount Direct Solar Pumping System. The solar array Ballasted ground mount system will consist be composed of 192 350-watt solar modules mounted in a ground field two 56 FT long arrays. There will be 9 strings of 10 panels, each individually fused going into the VariSun 25 HP Pump Inverter Control Panel. Additionally, the arrays will be connected to the Xxxxxxxxx 48 VDC charge controller for a total nameplate capacity of 67.2 kW. EV charging. Expected Make and Model of Equipment to be Installed (include modules and inverter): VariSun by Sustainable Technologies - VS-P25-GM xxxx://xxxxxxx.xx/?product=vs-p25-gm-25-hp-varisun-solar-pumping-system The brand of solar modules will be either Hanwha Q.cells 27 KW VariSun Pumping System component list follows: 300 watt – 60 cell Mission Solar or LGSeraphim Modules, purchased from a California vendor, US made. 90 Each 25 HP VariSun Solar pumping Inverter control panel 1 Each DC disconnects switchgear 9 Each NEMA 4 control panel with charging system for control power and will be standard 72-cell, 350-watt modules. As an off-grid facility, it will not require an inverter or grid connection. The mounting system will be a commercial ground irrigation controller 1 Each MPPT Solar controller 1 Each Brittmore Solway II Ground mount racking system from either Unirac or RBI Solar and will be determined at the start of the Project. 1 Set Expected Contractor(s), if known (include Contractor State License Board (CSLB) license number): XxXxxxxxx Corporation, CSLB #941211, will provide the license for the initial building permit application and will subcontract a licensed California solar installer for construction of the equipment prior to installation. Paired Power, Inc. Battery Energy Storage Sustainable Technologies 772329 b. Electric Vehicle Charger Description of where equipment will be installed on the property and the renewable energy source serving the charger (For example: located with solar system installed at northeast corner by greenhouse): The battery energy storage will be contained in a 297kWh Mobile Power Station (MPS48VDC utility car charger connected to the solar pump system. Is/are the vehicle(s) located at the Xxxxxx Xxxxx Farms Red Barn Facility, as described above. The battery energy storage will be a mobile system on wheels that requires no ground-based installation. Battery will be referenced above used for (For example, provide back up for grid outages; to regularly shift or extend hours of use for the installed solar energy system): The battery storage will be used to power a 252kWh MPS; agricultural operation specified in the MPS will be used primarily for spraying and mowing of the 3,600 acres of almond trees at Xxxxxx Xxxxx Farms; it may also be used as back-up power, as needed. XXXXXX Mobile Power Station (MPS) with BMW second-life lithium-ion battery modules with a total rated capacity of 297kWh. application? Yes No Expected Contractor(s), if known (include CSLB license number): XxXxxxxxx Corporation, CSLB #941211. The MPS used for energy storage will be provided by XX Xxxxxx, LLC.Sustainable Technologies 772329

TECHNICAL TASKS. The purpose of this task is successful procurement and installation of all project components identified in this Agreement. Solar photovoltaic (PV) Wind turbine Battery Energy Storage Pump replacement (conversion of fossil fuel pump to electric pump) Electric Vehicle Charging Infrastructure System 1 Project Detail a. Renewable Energy System Description of where equipment will be installed on the property (For example: northeast corner by barn): Solar array The solar system will be a ground mount system installed in an open area and on bare ground the east side of the equipment yard on APN 000- the south side of parcel 414-011-012-000-000 near the farm’s Red Barn Maintenance Facility, located adjacent to existing electric meters. For Solar PV, please identify the surface of installation: Rooftop If so, is the rooftop on an existing building? Yes No b. Parking lot (can be unpaved). If so, is it an existing parking lot? Yes No Ground-mounted or Floating (Solar Panels mounted on pontoons and floating on irrigation pond). Other: Electricity produced will be used to power serve (For example: greenhouse; irrigation pumps; electric vehicle charging): Electricity produced will be used to charge two zero-emission off-road equipment Irrigation pumps and mobile storage used for crop spraying from February through November and for year-round mowing for the farm’s almond tree cropelectric vehicle charging station. Rated Capacity of system: [ 67.2 [170.4] kW General Description of Equipment (please include information such as number of arrays or turbines): Six ground-mounted solar arrays configured 2 panels high in portrait will support 480 solar panels and 3 inverters. The solar array will consist of 192 350-watt solar modules mounted in a ground field for a total nameplate capacity of 67.2 kW. system’s footprint is approximately 145’ x 135’. Expected Make and Model of Equipment to be Installed (include modules and inverter): The brand of solar modules will be either Hanwha Q.cells or LGSeraphim, purchased from a California vendor, and will be standard 72SRP-355-cell, 3506MA-watt HV (355W) modules. As an off-grid facility, it will not require an ; Solectria PVI 50TL inverter or grid connection. The mounting system will be a commercial ground mount racking system from either Unirac or RBI Solar and will be determined at the start of the Project. Expected Contractor(s), if known (include Contractor State License Board (CSLB) CSLB license number): XxXxxxxxx Corporation, CSLB #941211, will provide the license for the initial building permit application and will subcontract a licensed California solar installer for construction of the equipment prior to installation. Paired PowerXxxxxxxx’x Energy, Inc. Battery Energy Storage CSLB # 999665 b. Electric Vehicle Charger Description of where equipment will be installed on the property and the renewable energy source serving the charger (For example: located with solar system installed at northeast corner by greenhouse): The battery energy storage charging station will be contained installed in a 297kWh Mobile Power Station (MPS) located at the Xxxxxx Xxxxx Farms Red Barn Facility, as described aboveemployee parking lot on the north side of the solar array. The battery energy storage charging station will be a mobile system on wheels that requires no ground-based installationserved by the 170.4 KW DC solar system. Battery will be used for (For example, provide back up for grid outages; to regularly shift or extend hours of use for the installed solar energy system): The battery storage Charger will be used to power a 252kWh MPS; serve (For example small car, off-road vehicles forklift, etc.): Employee owned small cars. Is/are the MPS will be vehicle(s) referenced above used primarily for spraying and mowing of the 3,600 acres of almond trees at Xxxxxx Xxxxx Farms; it may also be used as backagricultural operation specified in the application? Yes No PowerCharge Pro Series, Level 2, 3.3 KW, 16 Amp, Dual Port Wall-up power, as needed. XXXXXX Mobile Power Station mount (MPSP10DW) with BMW second-life lithium-ion battery modules with a total rated capacity of 297kWh. Expected Contractor(s), if known (include CSLB license number): XxXxxxxxx CorporationXxxxxxxx’x Energy, Inc. CSLB #941211. The MPS used for energy storage will be provided by XX Xxxxxx, LLC.# 999665

TECHNICAL TASKS. The purpose of this task is successful procurement and installation of all project components identified in this Agreement. Solar photovoltaic (PV) Wind turbine Battery Energy Storage Pump replacement (conversion of fossil fuel pump to electric pump) Electric Vehicle Charging Infrastructure System 1 Project Detail Task 1: Diesel to Solar Plus Storage a. Renewable Energy System Description of where equipment will be installed on the property (For example: northeast corner by barn): Solar array will be a ground mount system installed in an open area and The diesel conversion is located on bare ground on APN 000- the northeast side of parcel 000-000 near the farm’s Red Barn Maintenance Facility, located adjacent to existing electric meters000-000. For Solar PV, please identify the surface of installation: Rooftop If so, is the rooftop on an existing building? Yes No b. Parking lot (can be unpaved). If so, is it an existing parking lot? Yes No Ground-mounted or Floating (Solar Panels mounted on pontoons and floating on irrigation pond). Other: Electricity produced will be used to power serve (For example: greenhouse; irrigation pumps; electric vehicle charging): Electricity produced will be used to charge two zero-emission off-road equipment and mobile storage used for crop spraying from February through November and for year-round mowing for the farm’s almond tree crop7.5 HP submersible irrigation pump. Rated Capacity of system: [ 67.2 [19.8] kW General Description of Equipment (please include information such as number of arrays or turbines): Two ground-mounted solar arrays configured 2 panels high in portrait will support 56 solar panels and 1 inverter. The footprint of the solar array will consist of 192 350-watt solar modules mounted in a ground field for a total nameplate capacity of 67.2 kW. system is 39’ x 48’. Expected Make and Model of Equipment to be Installed (include modules and inverter): The brand of solar modules will be either Hanwha Q.cells or LGSeraphim, purchased from a California vendor, and will be standard 72SRP-355-cell, 3506MA-watt HV (355W) modules. As an off; SE20K-grid facility, it will not require an inverter or grid connection. The mounting system will be a commercial ground mount racking system from either Unirac or RBI Solar and will be determined at the start of the Project. USR48NNU 3-PH GRID TIED INVERTER 20KW 480VAC Expected Contractor(s), if known (include Contractor State License Board (CSLB) CSLB license number): XxXxxxxxx Corporation, CSLB #941211, will provide the license for the initial building permit application and will subcontract a licensed California solar installer for construction of the equipment prior to installation. Paired PowerXxxxxxxx’x Energy, Inc. CSLB # 999665 b. Battery Energy Storage Description of where equipment will be installed on the property and the renewable energy source serving the charger (For example: located with solar system installed at northeast corner by greenhouse): The battery energy diesel to solar plus storage system will be contained in a 297kWh Mobile Power Station (MPS) located at with solar system installed next to the Xxxxxx Xxxxx Farms Red Barn Facility, as described above. The battery energy storage will be a mobile system well on wheels that requires no groundthe northeast corner of the parcel 000-based installation000-000. Battery will be used for (For example, provide back up for grid outages; to regularly shift or extend hours of use for the installed solar energy system): The battery storage will be used to power a 252kWh MPS; the MPS will be used primarily for spraying and mowing of the 3,600 acres of almond trees at Xxxxxx Xxxxx Farms; it may also be used as provide back-up powerenergy for pumping when the solar system is not producing enough energy for on-demand pumping. For example, as neededwhen pumping is needed on cloudy days or at night. XXXXXX Mobile Princeton Power Station (MPS) with BMW secondPEMS 30-life lithium-ion battery modules with a total rated capacity of 297kWh. 60 Lithium Ion , 30 kW 60 kwh AC/30 kVA AC , 480 VAC +10%, -12%, 3- phase 3/4 wire- Heating/Cooling Package Expected Contractor(s), if known (include CSLB license number): XxXxxxxxx CorporationXxxxxxxx’x Energy, Inc. CSLB #941211. The MPS used for energy storage will be provided by XX Xxxxxx, LLC.# 999665