Scope of Supply 12.1 The Goods and Related Services to be supplied shall be as specified in the Schedule of Requirements.
Selection of Subcontractors, Procurement of Materials and Leasing of Equipment The contractor shall not discriminate on the grounds of race, color, religion, sex, national origin, age or disability in the selection and retention of subcontractors, including procurement of materials and leases of equipment. The contractor shall take all necessary and reasonable steps to ensure nondiscrimination in the administration of this contract. a. The contractor shall notify all potential subcontractors and suppliers and lessors of their EEO obligations under this contract. b. The contractor will use good faith efforts to ensure subcontractor compliance with their EEO obligations.
Continuity of Supply A Service Order will continue until terminated in accordance with this Agreement. A change to a Service Order will not initiate a new Service Order, or cause the existing Service Order to terminate, unless expressly agreed in writing. In particular, a change to a Service Order that is implemented by the LFC electronically and does not require a physical visit to a site or Interconnection Point will not cause the Service Order to terminate.
No Moving of Supplied Furnishings All furnishings and equipment supplied with the Room shall remain in the Room for the duration of the Term. All furnishings, if rearranged, must be returned to their original position found at the commencement of the Term. No common area furniture is to be moved into the Room.
Licenses for Permanent Installation The contractor must comply with all State mandatory licensing requirements prior to installation. Questions on licensing requirements should be directed to the State Licensing Board. Contractor must furnish and install all furniture and materials in compliance with all applicable codes, whether local, state, or federal; and that all permits or licenses required for installation will be obtained without cost to the State.
Equipment Specifications All equipment must meet the contract specifications and all federal and State safety codes and regulations in effect at the date of manufacture. All equipment must be Original Equipment Manufacturer (OEM) equipment unless otherwise stated in the contract. All products, materials, supplies, replacement parts, and equipment offered and furnished must be new, of current manufacturer production, and must have been formally announced by the manufacturer as being commercially available, unless otherwise stated in this Contract.
SUSPENSION OF SUPPLIER'S APPOINTMENT 31.1 If the Authority is entitled to terminate this Framework Agreement pursuant to Clause 30 (Authority Termination Rights), the Authority may instead elect in its sole discretion to suspend the Supplier's ability to accept Orders under this Framework Agreement by giving notice in writing to the Supplier, and the Supplier agrees that it shall not be entitled to enter into any new Call Off Agreement during the period specified in the Authority’s notice. 31.2 Any suspension under Clause 31.1 shall be without prejudice to any right of termination which has already accrued, or subsequently accrues, to the Authority. 31.3 The Parties acknowledge that suspension shall not affect the Supplier's obligation to perform any existing Call Off Agreements concluded prior to the suspension notice. 31.4 If the Authority provides notice to the Supplier in accordance with this Clause 31.1, the Supplier's appointment under this Framework Agreement shall be suspended for the period set out in the notice or such other period notified to the Supplier by the Authority in writing from time to time. 31.5 For the avoidance of doubt, no period of suspension under this Clause 31 shall result in an extension of the Framework Period.
DISCONNECTION OF SUPPLY 14.1 When can we arrange for disconnection? (a) you do not pay your bill by the pay-by date and, if you are a residential customer, you: (i) fail to comply with the terms of an agreed payment plan; or (ii) do not agree to an offer to pay the bill by instalments, or having agreed, you fail to comply with the instalment arrangement; (b) you do not provide a security deposit we are entitled to require from you; or (c) you do not give access to your premises to read a meter (where relevant) for 3 consecutive meter reads; or (d) you fail to give us safe and unhindered access to the premises as required by clause 11 or any requirements under the energy laws; or (e) there has been illegal or fraudulent use of energy at your premises in breach of clause 16 of this contract; or (f) we are otherwise entitled or required to do so under the Rules or by law.
Supply and Maintenance of Equipment It is the responsibility of the Employer to furnish and maintain all equipment, machinery and supplies required by employees in the performance of their duties. Employees shall not suffer any loss in salary in the event that they cannot carry out their normal duties by reason of the Employer failing to properly maintain equipment, machinery or supplies or by reason of power failures or other circumstances not attributable to the employees.
Testing of Metering Equipment Connecting Transmission Owner shall inspect and test all of its Metering Equipment upon installation and at least once every two (2) years thereafter. If requested to do so by NYISO or Developer, Connecting Transmission Owner shall, at Developer’s expense, inspect or test Metering Equipment more frequently than every two (2) years. Connecting Transmission Owner shall give reasonable notice of the time when any inspection or test shall take place, and Developer and NYISO may have representatives present at the test or inspection. If at any time Metering Equipment is found to be inaccurate or defective, it shall be adjusted, repaired or replaced at Developer’s expense, in order to provide accurate metering, unless the inaccuracy or defect is due to Connecting Transmission Owner’s failure to maintain, then Connecting Transmission Owner shall pay. If Metering Equipment fails to register, or if the measurement made by Metering Equipment during a test varies by more than two percent from the measurement made by the standard meter used in the test, Connecting Transmission Owner shall adjust the measurements by correcting all measurements for the period during which Metering Equipment was in error by using Developer’s check meters, if installed. If no such check meters are installed or if the period cannot be reasonably ascertained, the adjustment shall be for the period immediately preceding the test of the Metering Equipment equal to one-half the time from the date of the last previous test of the Metering Equipment. The NYISO shall reserve the right to review all associated metering equipment installation on the Developer’s or Connecting Transmission Owner’s property at any time.
