Test Methods. The procedures and methods used to sample and test material will be determined by the Project Designers. Unless otherwise specified, samples and tests shall be made in accordance with MAG 700 Series and the standard methods of AASHTO or ASTM as referenced in the MAG 700 Series.
Test Methods. 2.1 The free acceleration visible pollutants shall be measured with the engine in the maximum rated speed and maximum power condition.
2.2 At the request of the manufacturer, measurements shall also be made over a matrix of up to five other power/speed combinations for the de-speeded and de-rated engine to cover the range of speed and power allowed for in paragraph 6.3.4. of part I of this Regulation covering the modification of an engine type. In this case the steady state visible pollutants will also be measured with the engine rated at these other points, by the method described in annex 4 of this Regulation, to enable the free acceleration absorption coefficient to be corrected in accordance with paragraph 3 of this annex. These values shall be recorded in table 2 of annex 2 of this Regulation. The diagram below shows the six possible measuring points of the matrix and the range of power and speed governed by each point. UN ECE Regulation 24/03 31 percent of maximum torque at rated speed maximum percent of that speed 1 100 100 2 90 100 3 100 90 4 90 90 5 100 80 6 90 80 Each measuring point governs the power and speed area to the left of and below that point and is the measuring point for any engine rated in that area. For example the measuring point at "A" which is for the 90 per cent full load line and 100 per cent rated speed applies to the rated power/speed area bounded by ABCD on the diagram.
2.3 If the test is a bench test the engine shall be disconnected from the brake, the latter being replaced either by the rotating parts driven when no gear is engaged or by an inertia substantially equivalent to that of the said parts (see paragraph 7.3 of annex 1 to this Regulation). UN ECE Regulation 24/03 32
2.4 If the test is carried out on a vehicle the gear-change control shall be set in the neutral position and the drive between engine and gear-box engaged.
2.5 With the engine idling, the accelerator control shall be operated quickly, but not violently, so as to obtain maximum delivery from the injection pump. This position shall be maintained until maximum engine speed is reached and the governor comes into action. As soon as this speed is reached the accelerator shall be released until the engine resumes its idling speed and the opacimeter reverts to the corresponding conditions.
2.6 The operation described in paragraph 2.5 above shall be repeated not less than six times in order to clear the exhaust system and to allow for any necessary adjustment of...
Test Methods. ESAs may comply with the requirements of any combination of the following test methods at the manufacturer's discretion provided that this results in the full frequency range specified in paragraph 3.1. of this annex being covered:
Test Methods. The suggested methods for testing that gas supplied at the Inlet Point complies with the agreed specification are detailed below.
Test Methods. Analytical procedures and test methods for product quality shall be in accordance with Exhibit A. Such procedures shall be no less rigorous than standard industry procedures and shall be revised periodically by agreement between the Parties for this purpose. Seller shall provide Buyer with certification sheets in respect of the analysis and description of the properties of each lot of Styrene part or all of which is to be delivered to Buyer hereunder. Such certification sheets shall be provided promptly following completion of final analysis of samples of such lot.
Test Methods. 6/25/1998 12/29/2008 [Insert FR page number where document be- gins].
Test Methods. Upon completion of manufacture, Pfizer will test each batch of Products for conformance with the Product Specifications and cGMP in accordance with agreed-upon quality control test methods set forth on Schedule 7.1, the Quality & Technical Agreement or as otherwise requested by Xxxxxxx.
Test Methods. Methods of sampling and testing materials are in accordance with the Florida Methods (FM). If an FM does not exist for a particular test, perform the testing in accordance with the method specified in the Specification. When test methods or other standards are referenced in the Specifications without identification of the specific time of issuance, use the most current issuance, including interims or addendums thereto, at the time of bid opening.
Test Methods. The Parties agree that the Department will pursue a rulemaking to promulgate appropriate test methods for determining compliance with the Department’s coke battery standards in Article XXI (§2105.
Test Methods. 2.1. The test object shall be a circular cylinder that is 50±2 mm in external diameter, with a 10±2 mm high ring, contrasting in colour from the rest of the test object, located such that its lowest edge is 900±2 mm from the base of the test object.
2.2. The test conditions shall be as defined in paragraphs 6.2. of this Regulation
