Readings. The maximum of the readings relative to the limit (horizontal and vertical polarization and antenna location on the left and right-hand sides of the vehicle) in each of the 14 frequency bands shall be taken as the characteristic reading at the frequency at which the measurements were made.
Readings. The maximum of the readings relative to the limit (horizontal/vertical polarisation) in each of the 14 frequency bands shall be taken as the characteristic reading at the frequency at which the measurements were made. Annex 9 Method(s) of testing for immunity of electrical/electronic sub-assemblies to electromagnetic radiation
Readings. The maximum of the readings relative to the limit (horizontal/vertical polarization) in each of the 14 frequency bands shall be taken as the characteristic reading at the frequency at which the measurements were made. Annex 7 – Appendix 1 Figure 1 Open area test site: Electrical/electronic sub-assembly test area boundary Level clear area free from electromagnetic reflecting surfaces Figure 2 Test configuration for ESAs involved in "REESS charging mode coupled to the power grid" (example for biconical antenna) Dimensions in millimetres Legend: 1 ESA (grounded locally if required in test plan) 2 LV Test harness 3 LV Load simulator (placement and ground connection according to CISPR 25 paragraph 6.4.2.5) 4 Power supply (location optional) 5 LV Artificial network (AN) 6 Ground plane (bonded to shielded enclosure) 7 Low relative permittivity support (εr ≤ 1.4) 8 Biconical antenna 10 High-quality coaxial cable e.g. double-shielded (50 Ω) 11 Bulkhead connector 12 Measuring instrument 13 RF absorber material 14 Stimulation and monitoring system 15 XX xxxxxxx 16 HV load simulator 17 HV AN 18 HV power supply 19 HV feed-through 25 AC/DC charger harness 26 AC/DC load simulator (e.g. Programmable Logic Controller (PLC)) 27 AMN(s) or DC-charging-AN(s) 28 AC/DC power supply 29 AC/DC feed-through Annex 8 Method of measurement of radiated narrowband electromagnetic emissions from electrical/electronic sub‑assemblies
Readings. The maximum of the readings relative to the limit (horizontal and vertical polarization and antenna location on the left and right-hand sides of the vehicle) in each of the 14 frequency bands shall be taken as the characteristic reading at the frequency at which the measurements were made. Annex 6 Method of testing for immunity of vehicles to electromagnetic radiation
Readings. The headings of the paragraphs herein are inserted for convenience and shall not affect any interpretation of this Agreement.
Readings. Headings of the Articles and Sections of this Agreement are for the convenience of the parties only, and shall be given no substantive or interpretive effect whatsoever.
Readings. Unless otherwise specified, Design-Builder must have the surveyor described above take readings of the work and adjacent property at a minimum number of points as indicated in the Technical Specification. Additional monitoring points may be established as the Design-Builder determines to be necessary. Provide a proposed program, in writing, for settlement monitoring prior to the start of excavation or foundation work. Have readings taken weekly until the work is substantially complete.
Readings. The maximum of the readings relative to the limit (horizontal/vertical polarization) in each of the 13 frequency bands shall be taken as the characteristic reading at the frequency at which the measurements were made. Annex 7 – Appendix Annex 7 - Appendix Figure 1 Open area test site: Electrical/electronic sub-assembly test area boundary Level clear area free from electromagnetic reflecting surfaces 15 m minimum radius Test sample on ground plane 1 m Antenna Annex 8 Annex 8 METHOD OF MEASUREMENT OF RADIATED NARROWBAND ELECTROMAGNETIC EMISSIONS FROM ELECTRICAL/ELECTRONIC SUB-ASSEMBLIES
Readings. The section headings contained in this Agreement are inserted for convenience only and shall not affect in any way the meaning or interpretation of this Agreement.
Readings. The Pipeline User must ensure that the Tubridgi Parties may remotely access the measurements and readings taken by the Metering Equipment provided by the Pipeline User at each User Receipt Point.
