Testing at Manufacturer’s Place. 15.1.1. The purpose of factory acceptance is to verify that the Product production is satisfactory and that the Product is ready to be shipped to TTL.
Testing at Manufacturer’s Place Sample Clauses
Related to Testing at Manufacturer’s Place
API A. Reliant shall supply to Cardinal Health for Manufacturing and Packaging, at Reliant’s sole cost, the API and applicable reference standards in quantities sufficient to meet Reliant’s requirements for each Product as further set forth in Article 4. Prior to delivery of any of the API or reference standard to Cardinal Health for Manufacturing and Packaging, Reliant shall provide to Cardinal Health a copy of the API Material Safety Data Sheet (“MSDS”), as amended, and any subsequent revisions thereto. Reliant shall supply the API, reference standards, and Certificate of Analysis FOB the Facility no later than thirty (30) days before the scheduled Manufacture Date upon which such API will be used by Cardinal Health. Upon receipt of the API, Cardinal Health shall conduct identification testing of the API. Cardinal Health shall use the API solely and exclusively for Manufacturing and Packaging under this Agreement. The maximum volume of API that Reliant supplies to Cardinal Health shall not exceed the amount reflected in the Firm Commitment and the next six (6) months of the Rolling Forecast.
Shipment If any of the Major Components associated with any Unit is not Shipped on or before (with the prior approval of the Buyer) the Scheduled Major Component Shipment Date set forth in Attachment 1 for reasons attributable to the Seller and not excused elsewhere in this Contract, the Seller shall pay as liquidated damages, and not as a penalty, a sum calculated in accordance with the table below for each Unit for each day of delay after the Scheduled Major Component Shipment Date as set forth in Attachment 1 until actual Shipment of the last Major Component for such Unit: Days after Scheduled Major Component Shipment Date Liquidated Damages (per day or partial day) *** *** *** *** *** *** Such liquidated damages, if any, shall be computed based on the date of Shipment of the last Major Component for a given Unit and such computations shall disregard any part of or accessory to the Major Component which may be shipped separately and arrive later unless such part of or accessory to the Major Component is necessary for the installation of the Major Component.
Product Specifications The Company agrees that all Products sold to Xxxx hereunder shall conform to the respective specifications set forth on Schedule A or to such other specifications as are from time to time agreed upon by the Parties.
Millennium Compliance Borrower shall take all action necessary to assure that there will be no material adverse change to Borrower's business by reason of the advent of the year 2000, including without limitation that all computer-based systems, embedded microchips and other processing capabilities effectively recognize and process dates after April 1, 1999, except for personal office computers and network stations which will be compliant by October 1, 1999. At FINOVA's request, Borrower shall provide to FINOVA assurance reasonably acceptable to FINOVA that Borrower's computer-based systems, embedded microchips and other processing capabilities are year 2000 compatible.
Manufacturing Services Jabil will manufacture the Product in accordance with the Specifications and any applicable Build Schedules. Jabil will reply to each proposed Build Schedule that is submitted in accordance with the terms of this Agreement by notifying Company of its acceptance or rejection within three (3) business days of receipt of any proposed Build Schedule. In the event of Jabil’s rejection of a proposed Build Schedule, Jabil’s notice of rejection will specify the basis for such rejection. When requested by Company, and subject to appropriate fee and cost adjustments, Jabil will provide Additional Services for existing or future Product manufactured by Jabil. Company shall be solely responsible for the sufficiency and adequacy of the Specifications [***].
Quality Specifications SANMINA-SCI shall comply with the quality specifications set forth in its Quality Manual, incorporated by reference herein, a copy of which is available from SANMINA-SCI upon request.
Product Testing Upon request, Customer shall provide Operator a laboratory report for each Product delivery by Customer or Customer’s supplier. Operator will not be obligated to receive Contaminated Product for throughput through the Pipelines, nor will Operator be obligated to accept Product that fails to meet the applicable quality specifications for the Berths under the BAUTA and any Terminal Service Orders issued thereunder.
Manufacture (a) Manufacturer shall only manufacture the specific number of Products as requested by Company and at no time shall manufacture excess goods or overruns. Manufacturer shall not sell any Products bearing the Trademarks to any third parties without the express written consent of Company.
Products 1.1. The information (including but not limited to the quantity, rated hashrate, unit price (“Unit Price”), total price for one item (“Total Price (One Item)”), total price for all the items (“Total Purchase Price”) of Products to be purchased by Party B from Party A is as follows (“Products”):
Manufacturing Intrexon shall have the option and, in the event it so elects, shall use Diligent Efforts, to perform any manufacturing activities in connection with the Aquaculture Program that relate to the Intrexon Materials, including through the use of a suitable Third Party contract manufacturer. To the extent that Intrexon so elects, Intrexon may request that AquaBounty and Intrexon establish and execute a separate manufacturing and supply agreement, which agreement will establish and govern the production, quality assurance, and regulatory activities associated with manufacture of Intrexon Materials. Except as provided in Section 4.1, any manufacturing undertaken by Intrexon pursuant to the preceding sentence shall be performed in exchange for cash payments equal to Intrexon’s Fully Loaded Cost in connection with such manufacturing, on terms to be negotiated by the Parties in good faith. In the event that Intrexon does not manufacture Intrexon Materials or bulk quantities of other components of AquaBounty Products, then Intrexon shall provide to AquaBounty or a contract manufacturer selected by AquaBounty and approved by Intrexon (such approval not to be unreasonably withheld) all Information Controlled by Intrexon that is (a) related to the manufacturing of such Intrexon Materials or bulk qualities of other components of AquaBounty Products for use in the Field and (b) reasonably necessary to enable AquaBounty or such contract manufacturer (as appropriate) for the sole purpose of manufacturing such Intrexon Materials or bulk quantities of other components of AquaBounty Products. The costs and expenses incurred by Intrexon in carrying out such transfer shall be borne by Intrexon. Any manufacturing Information transferred hereunder to AquaBounty or its contract manufacturer shall not be further transferred to any Third Party, including any Product Sublicensee, or any AquaBounty Affiliate without the prior written consent of Intrexon; provided, however, that Intrexon shall not unreasonably withhold such consent if necessary to permit AquaBounty to switch manufacturers.
