Testing Facilities. 1. The Joint Company shall not be required to accept the plant or production facilities until, such time as it shall be wholly satisfied that the said production facilities are capable of producing the required products in the required quantities.
Testing Facilities. All testing under this policy will be conducted at Community Hospital Occupational Health Center, 0000 Xxxxx Xxxx Xxxx, Xxxxxxxxxxxx, XX (7am-11pm) or Community Hospital East, 0000 Xxxxx Xxxxxx Xxxxxx, Indianapolis, IN (after hours only).
Testing Facilities. Each participating school must provide a testing environment conducive to effective administration of the tests and one which meets the facilities requirements listed in The ACT for State Testing Standard Testing Requirements (see Attachment B). If a school is unable to meet the facilities requirements, they may apply to test off-site. The off-site location must meet the facilities requirements outlined in The ACT for State Testing Standard Testing Requirements (see Attachment B). To test off-site, schools must complete the off-site testing application which will be available on the ACT District Choice State Testing website in Fall 2011. Off-site testing may only be done with prior approval from ACT. Appointing Testing Staff Each high school principal must appoint a Test Supervisor. The Test Supervisor must meet ACT’s standard requirements for testing staff, provide documentation of the school’s secure storage facilities, and agree to ACT’s standard requirements for test administration as stated in The ACT for State Testing Standard Testing Requirements (Attachment B). The Test Supervisor will serve as the primary contact for all communications about the ACT administration, will receive test materials, will be responsible for conducting standardized and secure test administrations at the school, and ensure the prompt return of test materials to ACT. Each appointed Test Supervisor will be required to complete an ACT State Testing Test Supervisor Profile and submit the completed form to ACT. After review and approval of the Profile, all future communications about the test administration will be addressed to the designated Test Supervisor. Schools will also be required to appoint a Back-up Test Supervisor who meets the same criteria as the Test Supervisor, and who will be able to serve in the event that the designated Test Supervisor is unable to fulfill his/her administration duties. Each appointed Back-up Test Supervisor will be required to complete an ACT State Testing Back-up Test Supervisor Profile and submit the completed form to ACT. Schools will also appoint a Test Accommodations Coordinator (TAC) (see “Students Requesting Test Accommodations” below). This individual will be responsible for submitting requests for accommodations and coordinating the testing of students approved for those accommodations during the period of time between the spring initial test date and the makeup test date. The TAC will serve as the primary contact for all communicati...
Testing Facilities. Separate test terminal blocks or equivalent facilities shall be provided for the main Meters and check Meters of each circuit. The test facilities shall be near to the Meters involved.
Testing Facilities. Supplier/ Manufacturer shall have adequate in-house testing facilities for carrying out all routine tests & acceptance tests as per relevant Indian standards.
Testing Facilities. All switchgear units shall be provided with facilities to enable applied high voltage tests to be carried out on the units and associated H.V. cabling. To facilitate high voltage testing where access to busbar or circuit terminations is restricted, a device shall be provided to extend the termination points to a readily accessible position. When current transformers and protective relays are fitted, facilities shall be provided for primary and secondary injection tests to be carried out, such that wires and connections need not be disconnected for the tests.
Testing Facilities inspection equipment monitoring The supplier shall hold ready to measuring and testing equipment corresponding to the purpose of application which he requires for checking Xxxxxxxx Cosmetics specifications during serial production. The supplier must label all inspection devices and test control units which could have an effect on product quality. The inspection devices must be gauged with calibrated apparatus and adjusted prior to their application and at stipulated inspection intervals. The measuring equipment must clearly display the calibration status and/or documents concerning the calibration are to be prepared and retained. Capabilities of measuring equipment shall be verified for critical characteristics.
Testing Facilities. Specimens will be taken only at an off-site facility or laboratory licensed for such testing. When a specimen is obtained, the container or test tubes must remain in full view of the employee, and in the presence of the employee, must be sealed and labeled. Upon request, the employee may initial the container. All tests shall be performed by an off-site facility according to national and industry standards, procedures, and policies.
Testing Facilities. The bidder must indicate clearly about the various testing facilities for type test as well as for routine/sample tests as per relevant ISS is respect of M.S.Forged Pins as are available at their works. In case no testing facilities are available at the bidder's works particulars of the place where such testing is proposed to be conducted during the course of inspection must be indicated.
Testing Facilities. The bidder must indicate clearly about the various testing facilities for the acceptance tests as well as routine tests as per relevant ISS as are available at their works. In case no testing facilities are available at the bidder's works, particulars of the place where such testing is proposed to be conducted during the course of inspection must be indicated.
