Testing of Welds. All welding shall be checked by ultrasonic testing for all lengths of pipe (i.e. 100 % testing at the factory). Additionally, 10% of the joints shall be tested by radiography. All specials shall be tested 100% by radiography.
Testing of Welds Sample Clauses
Related to Testing of Welds
TESTING OF THE BCDR PLAN The Service Provider shall test the BCDR Plan on a regular basis (and in any event not less than once in every Contract Year). Subject to paragraph 6.2, the Purchaser may require the Service Provider to conduct additional tests of some or all aspects of the BCDR Plan at any time where the Purchaser considers it necessary, including where there has been any change to the Services or any underlying business processes, or on the occurrence of any event which may increase the likelihood of the need to implement the BCDR Plan. If the Purchaser requires an additional test of the BCDR Plan, it shall give the Service Provider written notice and the Service Provider shall conduct the test in accordance with the Purchaser's requirements and the relevant provisions of the BCDR Plan. The Service Provider's costs of the additional test shall be borne by the Purchaser unless the BCDR Plan fails the additional test in which case the Service Provider's costs of that failed test shall be borne by the Service Provider. The Service Provider shall undertake and manage testing of the BCDR Plan in full consultation with the Purchaser and shall liaise with the Purchaser in respect of the planning, performance, and review, of each test, and shall comply with the reasonable requirements of the Purchaser in this regard. Each test shall be carried out under the supervision of the Purchaser or its nominee. The Service Provider shall ensure that any use by it or any Sub-contractor of “live” data in such testing is first approved with the Purchaser. Copies of live test data used in any such testing shall be (if so required by the Purchaser) destroyed or returned to the Purchaser on completion of the test. The Service Provider shall, within twenty (20) Working Days of the conclusion of each test, provide to the Purchaser a report setting out: the outcome of the test; any failures in the BCDR Plan (including the BCDR Plan's procedures) revealed by the test; and the Service Provider's proposals for remedying any such failures. Following each test, the Service Provider shall take all measures requested by the Purchaser, (including requests for the re-testing of the BCDR Plan) to remedy any failures in the BCDR Plan and such remedial activity and re-testing shall be completed by the Service Provider, at no additional cost to the Purchaser, by the date reasonably required by the Purchaser and set out in such notice. For the avoidance of doubt, the carrying out of a test of the BCDR Plan (including a test of the BCDR Plan’s procedures) shall not relieve the Service Provider of any of its obligations under this Contract. The Service Provider shall also perform a test of the BCDR Plan in the event of any major reconfiguration of the Services or as otherwise reasonably requested by the Purchaser.
Testing of Metering Equipment Connecting Transmission Owner shall inspect and test all of its Metering Equipment upon installation and at least once every two (2) years thereafter. If requested to do so by NYISO or Developer, Connecting Transmission Owner shall, at Developer’s expense, inspect or test Metering Equipment more frequently than every two (2) years. Connecting Transmission Owner shall give reasonable notice of the time when any inspection or test shall take place, and Developer and NYISO may have representatives present at the test or inspection. If at any time Metering Equipment is found to be inaccurate or defective, it shall be adjusted, repaired or replaced at Developer’s expense, in order to provide accurate metering, unless the inaccuracy or defect is due to Connecting Transmission Owner’s failure to maintain, then Connecting Transmission Owner shall pay. If Metering Equipment fails to register, or if the measurement made by Metering Equipment during a test varies by more than two percent from the measurement made by the standard meter used in the test, Connecting Transmission Owner shall adjust the measurements by correcting all measurements for the period during which Metering Equipment was in error by using Developer’s check meters, if installed. If no such check meters are installed or if the period cannot be reasonably ascertained, the adjustment shall be for the period immediately preceding the test of the Metering Equipment equal to one-half the time from the date of the last previous test of the Metering Equipment. The NYISO shall reserve the right to review all associated metering equipment installation on the Developer’s or Connecting Transmission Owner’s property at any time.
Reporting of Metered Data and Parameters 7.2.1 The grid connected Solar PV power plants will install necessary equipment for regular monitoring of solar irradiance (including GHI, DHI and solar radiation in the module plane), ambient air temperature, wind speed and other weather parameters and simultaneously for monitoring of the electric power (both DC and AC) generated from the Project.
Processing of Grievance It is recognized and accepted by the Union and the County that the processing of grievances as hereinafter provided is limited by the job duties and responsibilities of the employees and shall therefore be accomplished during normal working hours only when consistent with such employee duties and responsibilities. The aggrieved employee's representative, if an employee, shall be allowed a reasonable amount of time without loss in pay, to investigate a grievance, and present grievances to the County during normal working hours provided the employee and the employee representative have notified the designated supervisor.
Performance Testing 7.2.1 The Design-Builder shall direct and supervise the tests and, if necessary, the retests of the Plant using Design-Builder’s supervisory personnel and the Air Emissions Tester shall conduct the air emissions test, in each case, in accordance with the testing procedures set forth in Exhibit A (the “Performance Tests”), to demonstrate, at a minimum, compliance with the Performance Guarantee Criteria. Owner is responsible for obtaining Air Emissions Tester and for ensuring Air Emissions Tester’s timely performance. Design-Builder shall cooperate with the Air Emissions Tester to facilitate performance of all air emissions tests. Design-Builder shall not be held responsible for the actions of Owner’s employees and third parties involved in the Performance Testing, including but not limited to Air Emissions Tester.
Posting of Seniority Lists See the Local Provisions Appendix L5.
Random Testing Notwithstanding any provisions of the Collective Agreement or any special agreements appended thereto, section 4.6 of the Canadian Model will not be applied by agreement. If applied to a worker dispatched by the Union, it will be applied or deemed to be applied unilaterally by the Employer. The Union retains the right to grieve the legality of any imposition of random testing in accordance with the Grievance Procedure set out in this Collective Agreement.
Posting of Seniority List The Administration shall post the seniority list twice annually by October 1 and March 1 of each work year. The seniority list shall be posted on the designated bulletin board in each building/work site and will indicate, by area of certification, license, or entry-level requirement, the first day worked, the date of Board resolution to hire, and the contract status (limited or continuing) of each employee. Said list shall be provided by the Superintendent to the Association President on or before the date of posting.
Testing Procedure A. For alcohol testing, the member shall be first given a breath test, at the collection site, followed by a confirmatory urine test only where the breath test reveals an initial positive alcohol level of .04 grams per 210 l. of breath. If the initial breath test results are below this level, testing shall be discontinued; if confirmatory urine tests results are below a level equivalent to .04 grams per 210 l. of breath, the confirmatory test shall be considered negative.
Office of Inspector General Investigative Findings Expert Review In accordance with Senate Bill 799, Acts 2021, 87th Leg., R.S., if Texas Government Code, Section 531.102(m-1)(2) is applicable to this Contract, Contractor affirms that it possesses the necessary occupational licenses and experience.
