Tool List. The following list of tools is the amount to be supplied by employees as a condition of employment:
Tool List. 1200 TOOLS
A. The following tools will be supplied by Linemen, Splicers, and Apprentices:
1 Set of Belt and Spurs, and a Fall Restricting System for pole climbing in accordance with IHSA and/or CSA standards 1 Harness with D in centre of back in accor- dance with the ISHA and/or CSA Standards 1 Skinning Knife
Tool List. All Labourers shall provide themselves with:
Tool List. Tools required by heavy duty mechanics are listed in a schedule on file with CLR and the Union.
Tool List. All journeymen electricians are required to have the following tools: 1 Centre Punch 1 1/2" Cold Chisel 1 Half-round File 1 Ball Peen Hammer
Tool List. Tools required by heavy duty mechanics are listed in a schedule on file with the Employer and the Union.
Tool List. Tool box Refrigeration Test manifold complete with hoses Pocket thermometer Adjustable Wrenches (crescent type – set consisting of (6”, 8”, 10”, 12”, & 16”) Pipe wrenches (8”, 14” and 24”) Refrigeration service wrenches (3/16” to ½”) Tube cutters (1/4” through 1 1/8”) Refrigeration flaring kit (imperial Xxxxxxx quality or equivalent) Screw drivers (complete set of flat, Xxxxxxxx, and Xxxxxxxx Combination wrenches (box end and open end ¼” through 1 1/8”) Pliers (needle nose, channel locks, combination, vice grips, linesman) Side cutter (and /or wire stripper) Hammers, ball peen (small and large ) and claw Xxxxx wrenches (set 1/16” to ½” and 2mm. To 12mm.) Punch and chisel set Leak detector (Halide or equivalent) Soldering and brazing kit (Turbo torch) Cordless electric drill (3/8”) Tape measure (25’, 1” width min.) Flash light Clamp on volt-Amp meter (Amprobe or better) One digital multi-meter (Fluke or equivalent) For winter operations a deflection meter is recommended Subject to approval by the Employer, any tools supplied by the Employee in addition to the above list will be identified in writing to the Employer. Employee supplied tools are to be of standard quality appropriate for the Refrigeration trade.
Tool List. Tools required by heavy duty mechanics are listed in a schedule on file with the Operating Engineers Training Plan.
Tool List. All Mechanics employed on maintenance and service must have the tools on the attached list and all Employees are guaranteed that while employed on the job site, project or place of business of the Employer, the Employee’s tools will be insured. The insurance covers fire and burglary or loss when working over water or such other areas where tools cannot be retrieved, and in the event of loss the Employer agrees to replace the tools. The Employer agrees to pay incidental tool loss claims in excess of two hundred dollars ($200.00) per year.
Tool List. 35.1 All journeymen sheet metal workers and apprentices shall provide themselves with a lockable toolbox and the full complement of tools as set out below: 1 scratch awl x x x x x x 1 xxxxxx'x hammer (16 ounces) x x x x x x 1 pair bull snips x x x x x x 1 small, medium & large screw drivers (slotted & Xxxxxxxxx) x x x x x x 1 rule 25' x x x x x x 1 xxxxxxx x x x x x x 1 tool box (lockable) x x x x x x 1 pair pliers x x x x x x 1 hacksaw frame x x x x x 1 pair vice grips x x x x x 1 right & left hand aircraft snips x x x x x 1 pair tongs folding x x x x x 1 xxxxx xxx & line x x x x x 1 chalk line x x x x x 1 crescent or adjustable wrench 10" x x x x x 1 ball peen hammer x x x x x
