Usage Measurement Usage measurement for calls shall begin when answer supervision or equivalent Signaling System 7 (SS7) message is received from the terminating office and shall end at the time of call disconnect by the calling or called subscriber, whichever occurs first.
Mileage Measurement Where required, the mileage measurement for LIS rate elements is determined in the same manner as the mileage measurement for V&H methodology as outlined in NECA Tariff No. 4.
Tenants Selection of Contractors Tenant shall retain Landlord’s contractor, Commerce Construction Co., L.P. (the “Contractor”), as general contractor for the performance of the Work.
Certain Calculations and Tests (a) Notwithstanding anything to the contrary herein, but subject to Sections 1.10(b) and (c) and Section 1.11, all financial ratios and tests (including the Total Leverage Ratio, the First Lien Leverage Ratio, the Secured Leverage Ratio, the Interest Coverage Ratio and the amount of Consolidated Total Assets and Consolidated Adjusted EBITDA) contained in this Agreement that are calculated with respect to any Test Period during which any Subject Transaction occurs shall be calculated with respect to such Test Period and each such Subject Transaction on a Pro Forma Basis. Further, if since the beginning of any such Test Period and on or prior to the date of any required calculation of any financial ratio or test (i) any Subject Transaction has occurred or (ii) any Person that subsequently became a Restricted Subsidiary or was merged, amalgamated or consolidated with or into the Borrower or any of its Restricted Subsidiaries or any joint venture since the beginning of such Test Period has consummated any Subject Transaction, then, in each case, any applicable financial ratio or test shall be calculated on a Pro Forma Basis for such Test Period as if such Subject Transaction had occurred at the beginning of the applicable Test Period (it being understood, for the avoidance of doubt, that solely for purposes of (x) calculating compliance with Section 6.12(a) and (y) calculating the First Lien Leverage Ratio for purposes of the definitions of “Applicable Rate” and “Commitment Fee Rate”, in each case, no Subject Transaction occurring after the end of the relevant Test Period shall be taken into account). (b) For purposes of determining the permissibility of any action, change, transaction or event that requires a calculation of any financial ratio or test (including, without limitation, Section 6.12(a), any First Lien Leverage Ratio test, any Secured Leverage Ratio test, any Total Leverage Ratio test and/or any Interest Coverage Ratio test, the amount of Consolidated Adjusted EBITDA and/or Consolidated Total Assets), such financial ratio or test shall be calculated at the time such action is taken (subject to Section 1.11), such change is made, such transaction is consummated or such event occurs, as the case may be, and no Default or Event of Default shall be deemed to have occurred solely as a result of a change in such financial ratio or test occurring after the time such action is taken, such change is made, such transaction is consummated or such event occurs, as the case may be. (c) Notwithstanding anything to the contrary herein, with respect to any amounts incurred or transactions entered into (or consummated) in reliance on a provision of this Agreement (including any covenant or the definition of “Incremental Cap”) that does not require compliance with a financial ratio or test (including, without limitation, Section 6.12(a), any First Lien Leverage Ratio test, any Secured Leverage Ratio test, any Total Leverage Ratio test and/or any Interest Coverage Ratio test) (any such amounts, the “Fixed Amounts”) substantially concurrently with any amounts incurred or transactions entered into (or consummated) in reliance on a provision of this Agreement (including any covenant or the definition of “Incremental Cap”) that requires compliance with a financial ratio or test (including, without limitation, Section 6.12(a), any First Lien Leverage Ratio test, any Secured Leverage Ratio test, any Total Leverage Ratio test and/or any Interest Coverage Ratio test) (any such amounts, the “Incurrence-Based Amounts”), it is understood and agreed that the Fixed Amounts shall be disregarded in the calculation of the financial ratio or test applicable to the Incurrence-Based Amounts.
Particular Methods of Procurement of Goods and Works International Competitive Bidding. Goods and works shall be procured under contracts awarded on the basis of International Competitive Bidding.
Use of Interconnection Facilities by Third Parties 6551 Error! Hyperlink reference not valid.9.9.1 Purpose of Interconnection Facilities. 6551
Use of Attachment Facilities by Third Parties Purpose of Attachment Facilities. Except as may be required by Applicable Laws and Regulations, or as otherwise agreed to among the Parties, the Attachment Facilities shall be constructed for the sole purpose of interconnecting the Large Generating Facility to the New York State Transmission System and shall be used for no other purpose.
Subadviser’s Services Are Not Exclusive Nothing in this Agreement shall limit or restrict the right of Subadviser or any of its partners, officers, or employees to engage in any other business or to devote his or her time and attention in part to the management or other aspects of any business, whether of a similar or a dissimilar nature, or limit or restrict Subadviser's right to engage in any other business or to render services of any kind to any other mutual fund, corporation, firm, individual, or association.
Other Methods of Procurement of Goods and Works The following table specifies the methods of procurement, other than International Competitive Bidding, which may be used for goods and works. The Procurement Plan shall specify the circumstances under which such methods may be used: (a) National Competitive Bidding (b) Shopping (c) Direct Contracting
Loop Testing/Trouble Reporting 2.1.6.1 Telepak Networks will be responsible for testing and isolating troubles on the Loops. Telepak Networks must test and isolate trouble to the BellSouth portion of a designed/non-designed unbundled Loop (e.g., UVL-SL2, UCL-D, UVL-SL1, UCL-ND, etc.) before reporting repair to the UNE Customer Wholesale Interconnection Network Services (CWINS) Center. Upon request from BellSouth at the time of the trouble report, Telepak Networks will be required to provide the results of the Telepak Networks test which indicate a problem on the BellSouth provided Loop. 2.1.6.2 Once Telepak Networks has isolated a trouble to the BellSouth provided Loop, and had issued a trouble report to BellSouth on the Loop, BellSouth will take the actions necessary to repair the Loop if a trouble actually exists. BellSouth will repair these Loops in the same time frames that BellSouth repairs similarly situated Loops to its End Users. 2.1.6.3 If Telepak Networks reports a trouble on a non-designed or designed Loop and no trouble actually exists, BellSouth will charge Telepak Networks for any dispatching and testing (both inside and outside the CO) required by BellSouth in order to confirm the Loop’s working status. 2.1.6.4 In the event BellSouth must dispatch to the end-user’s location more than once due to incorrect or incomplete information provided by Telepak Networks (e.g., incomplete address, incorrect contact name/number, etc.), BellSouth will xxxx Xxxxxxx Networks for each additional dispatch required to repair the circuit due to the incorrect/incomplete information provided. BellSouth will assess the applicable Trouble Determination rates from BellSouth’s FCC or state tariffs.
