Using the XIP TSR Interface Sample Clauses

Using the XIP TSR Interface. If you are running the card under DOS, you can use our DOS code and utilities. The application interfaces with the XIP by means of a Software Interrupt and the XIP, in turn, reads and writes to the shared memory areas. For details of using the XIP, see the code example later in this document. The application program will access the XIP software by means of the following commands: MOV BX, <data segment of control block> MOV DX, <offset of control block> INT <CALLING INTERRUPT> The XIP software will transfer the control block (and associated data buffer, if applicable) fro the application software and carry out the defined command. It will then update this control block at the application level with the required return code and, if applicable, the associated data buffer, data length etc. The XIP Control Block Structure is as follows: Parameter Off- set Lth Remarks COMMAN D 00H 1 Command code. BUFFER_ LENGTH 01H 2 Length of the data buffer associated with this call. RETURN_ CODE 03H 1 Result of the previous command. RESERVE D 04H 1 Reserved for HDLC interface. LOGICAL_ CHANNEL 05H 2 The X.25 logical channe concerned with this command. Q_D_M_BI TS 07H 1 The Q, D and M-bit settings in the X.25 packet to be transmitted or in the received packet. CAUSE 08H 1 The X.25 cause field in the packet to be transmitted or in the received packet. Parameter Off- set Lth Remarks DIAGNOS- TIC 09H 1 The X.25 diagnostic field in the packet to be transmitted or in the received packet. X25_ PACKET_ TYPE 0AH 1 The X.25 packet type - used for reporting exception conditions such as asynchronous X.25 packets received. TIME_ STAMP 0B H- 0EH 4 A time stamp - used when reporting asynchronous X.25 occurrences. RESERVE D 0FH 1 DATA 10H 104 0 This is the transfer area for passing data to and from the application level.
Sample 1
AutoNDA by SimpleDocs

Related to Using the XIP TSR Interface

  • Falls Far Below Target  Upon further review following a preliminary Pending rating, the Commission identifies significant financial risk and has concerns about financial viability such that heightened monitoring and/or intervention are necessary. 2.b.

  • -wire Unbundled Digital/DS0 Loop These are designed 4-wire Loops that may be configured as 64kbps, 56kbps, 19kbps, and other sub-rate speeds associated with digital data services and will come standard with a test point, OC, and a DLR.

  • Exceptional Access to Thick Registration Data In case of a registrar failure, deaccreditation, court order, etc. that prompts the temporary or definitive transfer of its domain names to another registrar, at the request of ICANN, Registry Operator will provide ICANN with up-­‐to-­‐date data for the domain names of the losing registrar. The data will be provided in the format specified in Specification 2 for Data Escrow. The file will only contain data related to the domain names of the losing registrar. Registry Operator will provide the data as soon as commercially practicable, but in no event later than five (5) calendar days following ICANN’s request. Unless otherwise agreed by Registry Operator and ICANN, the file will be made available for download by ICANN in the same manner as the data specified in Section 3.1 of this Specification.

  • Access Toll Connecting Trunk Group Architecture 9.2.1 If CBB chooses to subtend a Verizon access Tandem, CBB’s NPA/NXX must be assigned by CBB to subtend the same Verizon access Tandem that a Verizon NPA/NXX serving the same Rate Center Area subtends as identified in the LERG.

  • Unbundled Network Terminating Wire (UNTW) 2.8.3.1 UNTW is unshielded twisted copper wiring that is used to extend circuits from an intra-building network cable terminal or from a building entrance terminal to an individual End User’s point of demarcation. It is the final portion of the Loop that in multi-subscriber configurations represents the point at which the network branches out to serve individual subscribers.

  • YOUR BILLING RIGHTS - KEEP THIS NOTICE FOR FUTURE USE This notice tells you about your rights and our responsibilities under the Fair Credit Billing Act.

  • HHS Single Audit Unit will notify Grantee to complete the Single Audit Determination Form If Grantee fails to complete the form within thirty (30) calendar days after receipt of notice, Grantee maybe subject to sanctions and remedies for non-compliance.

  • Commingling of Resold Services with Unbundled Network Elements and Combinations of Unbundled Network Elements 6.7.1 To the extent it is Technically Feasible and pursuant to the terms of Section 9.1, CLEC may Commingle Telecommunications Services purchased on a resale basis with an Unbundled Network Element or combination of Unbundled Network Elements.

  • Multi-year Planning Targets Schedule A may reflect an allocation for the first Funding Year of this Agreement as well as planning targets for up to two additional years, consistent with the term of this Agreement. In such an event, the HSP acknowledges that if it is provided with planning targets, these targets:

  • Unbundled Voice Loop – SL2 (UVL-SL2 Loops may be 2-wire or 4-wire circuits, shall have remote access test points, and will be designed with a DLR provided to NewPhone. SL2 circuits can be provisioned with loop start, ground start or reverse battery signaling. OC is provided as a standard feature on XX0 Xxxxx. The OC feature will allow NewPhone to coordinate the installation of the Loop with the disconnect of an existing customer’s service and/or number portability service. In these cases, BellSouth will perform the order conversion with standard order coordination at its discretion during normal work hours.

Time is Money Join Law Insider Premium to draft better contracts faster.