Class VI injection well definition

Class VI injection well means the same as that term is defined in 40 C.F.R. 146.5(f).
Sample 1Sample 2
Class VI injection well means a well drilled
Sample 1Sample 2Sample 3
Class VI injection well means a well drilled pursuant to a permit for a class VI injection well issued under the federal "Safe Drinking Water Act", 42 U.S.C. sec. 300f et seq., as amended.
Sample 1

Examples of Class VI injection well in a sentence

  • As such, any Withdrawal of Carbon Dioxide from any Storage Reservoirs shall, to the extent reasonably practicable, be reinjected into any of the Storage Reservoirs listed in this Agreement or any other Class VI injection well permitted by the State.

  • However, upon a showing of good cause by Operator, this Agreement may be extended by the State in its discretion for up to an additional two (2) years at the end of the Initial Term (“Initial Discretionary Term”) if Operator has failed to apply for a permit to construct a Class VI injection well on the Property.

  • This Agreement shall terminate at the end of the Initial Term if Operator has failed to apply for a permit to construct a Class VI injection well on the Property.

  • If extended by an Initial Discretionary Term, then this Agreement shall terminate at the end of the Initial Discretionary Term if Operator has failed to apply for a permit to construct a Class VI injection well on the Property.

  • The type(s) of geophysical surveys conducted at a proposed Class VI injection well site are based on known site subsurface and surface conditions.

  • As part of a series of technical guidance documents, this guidance is intended to provide information and possible approaches for addressing various aspects of permitting and operating a Class VI injection well.

  • Because the surface and long-string casings in a Class VI injection well will be cemented to the surface [40 CFR 146.86(b)(2) and (3)], they will generally not be removed.

  • If results of such testing indicate artificial impacts, then adjustment of the model may be necessary prior to running the model for a proposed Class VI injection well AoR delineation.

  • The UIC Program staff who are responsible for reviewing and approving Class VI injection well permit applications and related reports concerning AoR delineation and corrective action are another intended audience of this guidance document.

  • Class VI injection well regulations are tailored to the characteristics of individual sites.


More Definitions of Class VI injection well

Class VI injection well means a well that is used to
Sample 1

Related to Class VI injection well

  • Injection well means a well into which fluids are injected. (See also “underground injection”.)

  • Injection means the injection of carbon dioxide streams into the storage site;

  • Underground injection means the subsurface emplacement of fluids through a bored, drilled or driven well; or through a dug well, where the depth of the dug well is greater than the largest surface dimension. (See also “injection well”.)

  • CO2 means carbon dioxide.

  • Flash point means the lowest temperature of a liquid at which its vapours form a flammable mixture with air;

  • Shallow well means a well located and constructed in such a manner that there is not a continuous layer of low-permeability soil or rock (or equivalent retarding mechanism acceptable to the department) at least 5 feet thick, the top of which is located at least 25 feet below the normal ground surface and above the aquifer from which water is to be drawn.

  • chemical tanker means a ship constructed or adapted and used for the carriage in bulk of any liquid product listed in chapter 17 of the International Bulk Chemical Code;

  • Injection tool means a device used for controlled subsurface injection of radioactive tracer material.

  • Horizontal well means a well bore drilled laterally at an angle of at least eighty (80) degrees to the vertical or with a horizontal projection exceeding one hundred (100) feet measured from the initial point of penetration into the productive formation through the terminus of the lateral in the same common source of supply.

  • CBM means Capacity Benefit Margin.

  • Finished water means the water that is introduced into the distribution system of a public water system and is intended for distribution and consumption without further treatment, except as treatment necessary to maintain water quality in the distribution system (e.g., booster disinfection, addition of corrosion control chemicals).

  • Gas well means a well producing gas or natural gas from a common source of gas supply as determined by the commission.

  • Residual disinfectant concentration (“C” in CT cal- culations) means the concentration of disinfectant measured in mg/l in a representative sample of water.

  • Ethanol blended gasoline means the same as defined in section 214A.1.

  • Exploration Well means a well that is not a development well, a service well or a stratigraphic test well.

  • Geothermal fluid means water in any form at temperatures greater than 120

  • Casing means a pipe or tubing of appropriate material, of varying diameter and weight, lowered into a borehole during or after drilling in order to support the sides of the hole and thus prevent the walls from caving, to prevent loss of drilling mud into porous ground, or to prevent water, gas, or other fluid from entering or leaving the hole.

  • Water well means an excavation that is drilled, cored, bored, augered, washed, driven, dug, jetted, or otherwise constructed for the purpose of exploring for groundwater, monitoring groundwater, utilizing the geothermal properties of the ground, or extracting water from or injecting water into the aquifer. “Water well” does not include an open ditch or drain tiles or an excavation made for obtaining or prospecting for oil, natural gas, minerals, or products mined or quarried.

  • Well-logging means all operations involving the lowering and raising of measuring devices or tools that may contain sources of radiation into well-bores or cavities for the purpose of obtaining information about the well or adjacent formations.

  • Bottled water means water that is placed in a safety sealed container or package for human 696 consumption. Bottled water is calorie free and does not contain sweeteners or other additives except 697 that it may contain: (i) antimicrobial agents; (ii) fluoride; (iii) carbonation; (iv) vitamins, minerals, and 698 electrolytes; (v) oxygen; (vi) preservatives; and (vii) only those flavors, extracts, or essences derived 699 from a spice or fruit. "Bottled water" includes water that is delivered to the buyer in a reusable 700 container that is not sold with the water.

  • Recycled water or “reclaimed water” means treated or recycled waste water of a quality suitable for non-potable uses such as landscape irrigation and water features. This water is not intended for human consumption.

  • Meet Point A point, designated by the Parties, at which one Party’s responsibility for service begins and the other Party’s responsibility ends.

  • Produced water means water recovered from an underground reservoir as a result of crude oil, condensate, or natural gas production and which may be recycled, disposed, or re-injected into an underground reservoir.

  • Pump spray means a packaging system in which the product ingredients within the container are not under pressure and in which the product is expelled only while a pumping action is applied to a button, trigger or other actuator.

  • Slug means any discharge of water, sewage, or industrial waste which in concentration of any given constituent or in quantity of flow exceeds for any period of duration longer than fifteen (15) minutes more than five (5) times the average twenty-four (24) hour concentration or flows during normal operation.

  • Infiltrative surface means designated interface where effluent moves from distribution media or a distribution product into treatment media or original soil. In standard trench or bed systems this will be the interface of the distribution media or product and in-situ soil. Two separate infiltrative surfaces will exist in a mound system and an unlined sand filter, one at the interface of the distribution media and fill sand, the other at the interface of the fill sand and in-situ soil.