Cleaning verification definition

Cleaning verification means a protocol for use by certified lead−safe renovators after completion of renovation activities, and in lieu of clearance dust−wipe sampling, that ensures post−renovation cleaning has been successfully com- pleted to the standard set under s. DHS 163.14 (11) (L).
Sample 1Sample 2Sample 3
Cleaning verification means collection of evidence by means of chemical testing after every batch or campaign to confirm that the amount of the residues of the previous products or detergents after cleaning is lower than the scientifically justified maximum permissible transfer level;
Sample 1

Examples of Cleaning verification in a sentence

  • Cleaning verification need not be performed if dust clearance testing is required at the conclusion of a renovation.

  • Cleaning verification would consist of wiping the interior windowsills and uncarpeted floors with wet disposable cleaning cloths and, if necessary dry disposable cleaning cloths, and comparing each to a cleaning verification card developed and distributed by EPA.

  • Cleaning verification, as well as the other components of the work practices being finalized today were not effective when high dust generation practices such as power planing (including power sanding) and high temperature heat guns were used.

  • Cleaning verification is required to ensure the work area is adequately cleaned and ready for re-occupancy.

  • Cleaning verification after each product campaign should be considered as a detectability tool to support effectiveness of the Quality Risk Management approach for products deemed to present higher risk;iv.

  • Cleaning verification is required to ensure the work area is adequately cleaned and ready for re-occupancy.See Flow Chart 6 for instructions on performing cleaning verification for interior projects.

  • Cleaning verification cardsare available by calling the National Lead Information Center at 1-800- 424-LEAD (5323).

  • Cleaning verification need not be performed if the contract between the renovation firm and the person contracting for the renovation or another federal, state, territorial, tribal or local law requires dust wipe sampling.

  • Cleaning verification may only be performed by an EPA Certified Renovator if renovations covered by the Renovation, Repair and Painting rule were performed.

  • Cleaning verification need not be performed if the contract between the renovation firm and the person contracting for the renovation or another federal, state, ter- ritorial, tribal or local law requires dust wipe sampling.

Related to Cleaning verification

  • Testing means that element of inspection that determines the properties or elements, including functional operation of materials, equipment, or their components, by the application of established scientific principles and procedures.

  • Verification means the process of comparing sets of data to establish the validity of a claimed identity (one-to-one check);

  • Cleaning means the act of removing septage or other wastes from a wastewater treatment system component or grease/waste from a grease interceptor.

  • Recalibration means the adjustment of all DRG weights to reflect changes in relative resource consumption.

  • Sampling means the distribution of samples to members of the general public in a public place.

  • Busy Line Verification (BLV means a service whereby an End User requests an operator to confirm the busy status of a line.

  • Screening means the evaluation process used to identify an individual's ability to perform activities of daily living and address health and safety concerns.

  • Calibration means the determination of (1) the response or reading of an instrument relative to a series of known radiation values over the range of the instrument, or (2) the strength of a source of radiation relative to a standard.

  • Test means such test as is prescribed by the particulars or considered necessary by the Inspecting Officer whether performed or made by the Inspecting Officer or any agency acting under the direction of the Inspecting Officer;

  • Dry cleaning means any industrial or commercial activity using VOCs in an installation to clean garments, furnishings and similar consumer goods with the exception of the manual removal of stains and spots in the textile and clothing industry;

  • Quality Management System means a set of interrelated or interacting elements that organisations use to direct and control how quality policies are implemented and quality objectives are achieved;

  • Onsite means within the Prescribed Premises boundary.

  • Contractor System means the information and communications technology system used by the Contractor in performing the Services including the Software, the Contractor Equipment and related cabling (but excluding the Authority System).

  • Verification Report As defined in Section 4.19.

  • Validation as used in WAC 222-20-016, means the department's agreement that a small forest landowner has correctly identified and classified resources, and satisfactorily completed a roads assessment for the geographic area described in Step 1 of a long-term application.

  • Samples mean representative physical examples of materials, equipment or workmanship, used to confirm compliance with requirements and/or to establish standards for use in execution of the Work.