Delay time definition

Delay time means the difference in time between the change of the component to be measured at the reference point and a system response of 10 per cent of the final reading (t10) with the sampling probe being defined as the reference point.

Delay time means the time between the change of the component to be measured at the reference point and a system response of 10 % of the final reading (t10). For the gaseous components, this is basically the transport time of the measured component from the sampling probe to the detector. For the delay time, the sampling probe is defined as the reference point;

Delay time means the time from the gas flow switching (t0) until the response reaches 10 per cent (t10) of the final reading.

Examples of Delay time in a sentence

• In the event of any such Excusable Delay, time for performance shall be extended for a period of time as may be reasonably necessary to compensate for such delay.

• Start ByteCommand ByteData BytesEnd Byte0XAA0x00None0xCC 0x33 0xC3 0x3COr add the Delay time Description: Check the interface board communicationClass: Single Byte CommandCode: 00hex, 00decExample : The Output information depend on configuration.

• Start ByteCommand ByteData BytesEnd Byte0XAA0x41PITCH_X PITCH_Y0xCC 0x33 0xC3 0x3COr add the Delay time Description: Set the character FONT display pitch.

• Start ByteCommand ByteData BytesEnd Byte0XAA0x40Front Color MSB Front Color LSB BK Color MSB BK Color MSB0xCC 0x33 0xC3 0x3COr add the Delay time Description: Set Front Color and Back Color.

• Delay time is further broken down into queuing delay (QD) and setup delay (SD).

• The No-Material- Delay time starts and material gaps (disturbance) can be eliminated.No-Material-Delay(period time)Standard Setting: 10sSetting Range: 1….100sUnit: SecondsCA/CF/CK: inactiveCC/CH: The accumulation stopps if the moisture value is below the Moisture Threshold.

• Start ByteCommand ByteData BytesEnd Byte0XAA0x43X MSB X LSB Y MSB Y MSB0xCC 0x33 0xC3 0x3COr add the Delay time Description: Get the (X,Y) display color data and set to the Front color.Class: Multi Byte CommandCode: 43hex, 67dec 7 6 5 4 3 2 1 0SET_FRONT_COLOR By X,Y 0x42X_MSB X_LSB Y_MSB Y_LSB Example : Read the (X,Y)=(128,64) color data and set to the Front color.

• Delay time is defined as the period of time in hours, or part thereof, that a delivery truck has to wait before it can deliver its load or if the ordered load does not fit.

• Delay time (DT) refers to the non-value-added time needed in order for an instance to be processed by a task.

• The following software settings give typical values for parameters that remain relatively constant in day-to-day operation: ANALYTE:AsSePrimary lamp current:27.5 mA20 mABoost lamp current:35 mA25 mAGain:10010Pump 1 speed:100100Pump 2 speed:5050Range (ppb):0 – 500 - 10Mode:Pk heightPk areaTypical sensitivity (1 ppb):20500 PROCEDURE: Delay time: 30 sec.

More Definitions of Delay time

Delay time means the time between the change of the component to be measured at the reference point and a system response of 10 per cent of the final reading (t10). For the gaseous components, this is basically the transport time of the measured component from the sampling probe to the detector. For the delay time, the sampling probe is defined as the reference point;

Delay time means the time from the gas flow switching...

Delay time means the difference in time between the change of the component to Deleted: <#>"Conversion efficiency

Delay time means the time from first ring until xxxxxx speaks with CSR. Minimum delay time: 180 seconds quarterly average. $5,000 per quarter if > 180 second avg. per quarter.