Engine starting definition

Engine starting means the process from the initiation of engine cranking until the engine reaches a speed 150 min-1 below the normal, warmed up idle speed (as determined in the drive position for vehicles equipped with an automatic transmission).

Examples of Engine starting in a sentence

  • Through DG controller) In the manual mode master generator set shall be started by pressing ‘Engine Start’ Push Button (PB) When Engine starting push button is pressed cranking relay shall be energized and give starting signal to the engine. After full voltage is build up, breaker of the Master generator shall close manually with the help of breaker control switch. When breaker Control switch is turned to ‘CLOSE’ position, breaker as per following sequence:a.

  • Series motor and its characteristics, Compound wound motor, Engine starting circuit, Starter drives-Bendix (torsion, compression), over-running clutch and sliding armature types.

  • Pre-flight operations & departure pass fail n/a a Pre-flight documentation NOTAM and Weather briefing b Mass & balance and performance calculation c Aeroplane inspection & servicing d Engine starting and after starting procedures e Taxiing & aerodrome procedures, pre take-off procedures f Take-off and after take-off checks g Aerodrome departure procedures h ATC compliance & R/T procedures Examiner initials Section 2.

  • Engine starting – Ni-Cd shines in this application but can be cost prohibitive.

  • Products that may contain stabilized formulations of reactive or time-sensitive chemicals include but are not limited to:  Catalysts containing methyl ethyl ketone peroxide (MEKP) PVC pipe primers Engine starting fluids.

  • Fuel Cell APU Testing • Actual vehicle loads measured and characterized,• Fuel cell and super- capacitor bank sized for vehicle loads,• Bench test conducted to test APU with vehicle loads.Fuel Cell APU Testing Engine starting and operational currents from battery.

  • Series motor and its characteristics, Compound wound motor, Engine starting circuit, Starter drives‐Bendix (torsion, compression), over‐running clutch and sliding armature types.

  • Engine starting batteries are to be located as close as practicable to the engines served.

  • Engine starting shall be manual by push-button or automatic through control system at control panel.

  • Engine starting procedures also required the ability to monitor the electrical system and RPM during the starting procedure.

Related to Engine starting

  • Engine degreaser means a cleaning product designed to remove grease, grime, oil and other contaminants from the external surfaces of engines and other mechanical parts.

  • Engine under the Lease. The term "Engines" means, as of any date of determination, both Engines then leased to the Lessee pursuant to the Lease.

  • Double Phase Aerosol Air Freshener means an aerosol air freshener with the liquid contents in two or more distinct phases that requires the product container be shaken before use to mix the phases, producing an emulsion.

  • Single Phase Aerosol Air Freshener means an aerosol air freshener with the liquid contents in a single homogeneous phase and which does not require that the product container be shaken before use.

  • Diesel engine means an engine which works on the compression-ignition principle.

  • Yearly (1/Year) sampling frequency means the sampling shall be done in the month of September, unless specifically identified otherwise in the effluent limitations and monitoring requirements table.

  • Yearly (1/Year) sampling frequency means the sampling shall be done in the month of September, unless specifically identified otherwise in the effluent limitations and monitoring requirements table.

  • Engines means, as of any date of determination, all Engines then leased hereunder.

  • Process weight means the total weight of all materials introduced into any source operation. Solid fuels charged will be considered as part of the process weight, but liquid and gaseous fuels and combustion air will not.

  • technical specification means a document that prescribes technical requirements to be fulfilled by a product, process or service;

  • Aircraft means any machine that can derive support in the atmosphere from the reactions of the air other than the reactions of the air against the earth’s surface;

  • APU means the auxiliary power unit of the Aircraft.

  • airframes means airframes (other than those used in military, customs or police services) that, when appropriate aircraft engines are installed thereon, are type certified by the competent aviation authority to transport:

  • Sewage sludge weight means the weight of sewage sludge, in dry U.S. tons, including admixtures such as liming materials or bulking agents. Monitoring frequencies for sewage sludge parameters are based on the reported sludge weight generated in a calendar year (use the most recent calendar year data when the NPDES permit is up for renewal).

  • Model shall refer to a particular brand of Vehicle sold by an OEM (e.g., Taurus, Tahoe, Grand Caravan).

  • Airframe means the Aircraft excluding the Propulsion Systems.

  • Life-cycle cost means the expected total cost of ownership during the life of a product, including disposal costs.

  • Compression Ignition Engine means an internal combustion engine with operating characteristics significantly similar to the theoretical diesel combustion cycle. The regulation of power by controlling fuel supply in lieu of a throttle is indicative of a compression ignition engine.

  • Propeller means for a device for propelling an aircraft that has blades on a powerplant driven shaft and that, when rotated, produces by its action on the air, a thrust approximately perpendicular to its plane of rotation and it includes control components normally supplied by its manufacturer, but does not include main and auxiliary rotors or rotating airfoils of powerplants;

  • Service Specification means and includes detailed description, statements to technical data, performance characteristics, and standards (Indian as well as International) as applicable and as specified in the Contract, as well as those specifications relating to Industry standards and codes applicable to the performance of the work, work performance quality and specifications affecting the work or any additional specification required to be produced by the Bidder to meet the design criteria.

  • Tare Weight means the weight of an empty shipping container, excluding all materials used for wrapping, cushioning, banding, waterproofing, packaging, blocking and bracing articles within the exterior container.

  • Collimator means a radiation shield that is placed on the end of the guide tube or directly onto a radiographic exposure device to restrict the size of the radiation beam when the sealed source is cranked into position to make a radiographic exposure.

  • Hot Weather Alert means the notice provided by PJM to PJM Members, Transmission Owners, resource owners and operators, customers, and regulators to prepare personnel and facilities for extreme hot and/or humid weather conditions which may cause capacity requirements and/or unit unavailability to be substantially higher than forecast are expected to persist for an extended period.

  • Civil aircraft means any aircraft other than a public aircraft.

  • Configuration means State-specific changes made to the Software without Source Code or structural data model changes occurring.

  • Technical Specifications A specification in a document defining the characteristics of a product or a service, such as the quality levels, the environmental and climate performance levels, the design for all needs, including accessibility for people with disabilities, and the evaluation of conformity, of product performance, of the use of the product, safety or dimensions, as well as requirements applicable to the product as regards the name by which it is sold, terminology, symbols, testing and test methods, packaging, marking or labelling, instructions for use, the production processes and methods at every stage in the life cycle of the supply or service, as well as the evaluation and conformity procedures;