Loop flows definition

Loop flows means the physical flow on a line where the source and sink are located in the same bidding zone and the line or even part of the tie-line is located in a different bidding zone;
Loop flows means the physical flow on a line where the source and sink are located in the same 'cross-border relevant network element' or 'XNE' means a network element identified as cross-border relevant and on which operational security violations need to be managed in a coordinated way;
Loop flows preventive (X)RA’ means a remedial action that is the result of an operational planning process and needs to be activated prior to the investigated timeframe for compliance with the (N-1) criterion;

Examples of Loop flows in a sentence

  • Loop flows can exist at the same time that inadvertent interchange is zero.

  • Loop flows are the difference between actual and scheduled power flows at a specific interface.

  • Loop flows affecting ATC calculation should be taken into account consistently by using the same models and assumptions as used for the planning of the system.

  • Loop flows are the difference between actual and scheduled power flows at specific interfaces.

  • In Mexico, women often marry young and start popping out babies, even if they are not mentally or physically ready.

  • Loop flows exist because electricity flows on the path of least resistance regardless of the path specified by contractual agreement or regulatory prescription.

  • Loop flows are generally defined as those unscheduled flows that are caused by scheduled flows within a neighbouring bidding zone.

  • PST flows, Loop flows and Internal flows are assigned fully to the bidding zone of their origin.

  • Loop flows are measured as the difference between actual and scheduled flows at one or more specific interfaces.

  • Loop flows that occur in the power system must be included in the load flow models that simulate power system conditions.

Related to Loop flows

  • Continuous parameter monitoring system (CPMS means all of the equipment necessary to meet the data acquisition and availability requirements of the Prevention of Significant Deterioration program, to monitor process and control device operational parameters (for example, control device secondary voltages and electric currents) and other information (for example, gas flow rate, O2 or CO2 concentrations), and to record average operational parameter value(s) on a continuous basis.

  • Continuous emissions monitoring system (CEMS means all of the equipment that may be required to meet the data acquisition and availability requirements of this section, to sample, condition (if applicable), analyze, and provide a record of emissions on a continuous basis.

  • Continuous emission monitoring system or "CEMS" means the equipment required under section 11 of this rule to sample, analyze, measure, and provide, by means of readings recorded at least once every fifteen (15) minutes, using an automated data acquisition and handling system (DAHS), a permanent record of nitrogen oxides emissions, stack gas volumetric flow rate, stack gas moisture content, and oxygen or carbon dioxide concentration, as applicable, in a manner consistent with 40 CFR 75*. The following systems are the principal types of continuous emission monitoring systems required under section 11 of this rule:

  • Best available control technology (BACT means an emissions limitation (including a visible emission standard) based on the maximum degree of reduction for each pollutant subject to regulation under CAA which would be emitted from any proposed major stationary source or major modification which the Department, on a case-by-case basis, takes into account energy, environmental, and economic impacts and other costs, determines is achievable for such source or modification through application of production processes or available methods, systems, and techniques, including fuel cleaning or treatment or innovative fuel combustion techniques for control of such pollutant. In no event shall application of best available control technology result in emissions of any pollutant which would exceed the emissions allowed by any applicable standard under 7 DE Admin. Code 1120 and 1121. If the Department determines that technological or economic limitations on the application of measurement methodology to a particular emissions unit would make the imposition of an emissions standard infeasible, a design, equipment, work practice, operational standard, or combination thereof, may be prescribed instead to satisfy the requirement for the application of best available control technology. Such standard shall, to the degree possible, set forth the emissions reduction achievable by implementation of such design, equipment, work practice or operation, and shall provide for compliance by means which achieve equivalent results.

  • Free Cash Flow means, for any Person for any period, EBITDA plus cash interest income of such Person for such period, less income taxes, Capital Expenditures and Investments (to the extent made in compliance with this Agreement), Scheduled Debt Service (if any) and variations in working capital made in the ordinary course of business, with respect to such period.

  • Monitoring System means a system established by BNY to fulfill the Responsibilities specified in clauses (d) and (e) of Section 1 of Article III of this Agreement.

  • Peak flow means the maximum instantaneous rate of flow of water at a particular point resulting from a storm event.