Maximum deviation definition

Maximum deviation is a parameter set by the Client on the client's terminal that determines the maximum deviation (in pips) between the execution price and the requested price when opening and closing a position.
Sample 1Sample 2Sample 3
Maximum deviation is a parameter set by the "พนทสวนบค "บค คลทเี' กย วขอ งกบ การเมอ
Sample 1

Examples of Maximum deviation in a sentence

  • The video will be examined to verify that the path is within the following deviation specifications: Maximum deviation of the boat at the guide buoys - 20 cm toward the buoy.

  • DefinitionsGeneral: For the purposes of this worksection the definitions given below apply.Absolute level tolerance: Maximum deviation from design levels.Relative level tolerance: Maximum deviation from a 3 m straightedge laid on the surface Channels and kerbs: Includes all forms of concrete gutters, dish drains, grated drains andmountable barrier kerbing.

  • Maximum deviation is attained for a Hill coefficient of 1 in agreement with the theoretical bounds (solid yellow lines).

  • Maximum deviation from the approved parameters shall be less than 5%.

  • DefinitionsFor the purposes of this worksection the definitions given below apply.Absolute level tolerance: Maximum deviation from design levels.Relative level tolerance: Maximum deviation from a 3 m straight edge laid on the surface.

  • Maximum deviation from the vertical of the extension rods during driving shall be 5%.

  • Maximum deviation allowed for A- and E- scores During the competitions, the difference between the middle scores taken into account may not be greater than: Final score between10.00 If a bigger deviation than indicated above occurs then the average of all four scores is the final score.

  • Maximum deviation is observed for d = 2 mm where the PNM result is closer to that of Holub et al.

  • Maximum deviation from stated line and grade of conductor pipe shall be such that line and grade of the sanitary sewer pipe can be adjusted a sufficient amount within the conductor pipe to achieve the line and grade shown on the plans to within 0.25 feet per 100 feet, unless otherwise directed by the District Manager.

  • In locating cores, fixings and embedded items, displace but do not cut reinforcement, and maintain documented cover to reinforcement.Isolation: Isolate embedded items to prevent water tracking to concrete that provides minimum cover to reinforcement.TolerancesGeneral: Maximum deviation from correct positions:- Anchor bolt groups for structural steel: To AS/NZS 5131.- Cores and embedded items generally: 10 mm.- Other fixing bolts: 3 mm.Edit as necessary to suit project requirements.

Related to Maximum deviation

  • Maximum Demand means the greatest demand required by a customer during a specific length of time.

  • Maximum Daily Quantity means the daily volume of Gas or Liquids, expressed in 103m3, identified in a Shipper's Interruptible Transportation Service Agreement that Transporter agrees to receive from Shipper under Toll Schedule Interruptible Full Path Service, Toll Schedule Interruptible Receipt Service or Toll Schedule Interruptible Delivery Service, as applicable.

  • Minimum Denomination has the meaning set forth in Article IV of the Debt Agreement.

  • Total maximum daily load or "TMDL" means the sum of the individual wasteload allocations for point sources, load allocations (LAs) for nonpoint sources, natural background loading and a margin of safety. TMDLs can be expressed in terms of either mass per time, toxicity, or other appropriate measure. The TMDL process provides for point versus nonpoint source trade-offs.

  • Maximum allowable cost list means a list of drugs for

  • SOFR Adjustment Conforming Changes means, with respect to any SOFR Rate, any technical, administrative or operational changes (including changes to the interest period, timing and frequency of determining rates and making payments of interest, rounding of amounts or tenors, and other administrative matters) that the Administrator decides, from time to time, may be appropriate to adjust such SOFR Rate in a manner substantially consistent with or conforming to market practice (or, if the Administrator decides that adoption of any portion of such market practice is not administratively feasible or if the Administrator determines that no market practice exists, in such other manner as the Administrator determines is reasonably necessary).

  • Reference Interest Rate Replacement Conforming Changes means, with respect to any Reference Interest Rate Replacement, any technical, administrative or operational changes (including changes to the definition of "Interest Period", timing and frequency of determining rates and making payments of interest, changes to the definition of "Corresponding Tenor" solely when such tenor is longer than the Interest Period and other administrative matters) that the Issuer or its designee decides may be appropriate to reflect the adoption of such Reference Interest Rate Replacement in a manner substantially consistent with market practice (or, if the Issuer or its designee decides that adoption of any portion of such market practice is not administratively feasible or if the Issuer or its designee determines that no market practice for use of the Reference Interest Rate Replacement exists, in such other manner as the Issuer or its designee determines is reasonably necessary).

  • Maximum Facility Output means the maximum (not nominal) net electrical power output in megawatts, specified in the Interconnection Service Agreement, after supply of any parasitic or host facility loads, that a Generation Interconnection Customer’s Customer Facility is expected to produce, provided that the specified Maximum Facility Output shall not exceed the output of the proposed Customer Facility that Transmission Provider utilized in the System Impact Study.

  • Maximum allowable cost means the maximum amount that a pharmacy benefit manager will reimburse a pharmacy for the cost of a drug.