Bioassay means the determination of kinds, quantities or concentrations and, in some cases, the locations of radioactive material in the human body, whether by direct measurement, in vivo counting, or by analysis and evaluation of materials excreted or removed from the human body. For purposes of these rules, “radiobioassay” is an equivalent term.
Third Party Components means software and interfaces, licensed by RIM from a third party for incorporation into a RIM software product, or for incorporation into firmware in the case of RIM hardware products, and distributed as an integral part of that RIM product under a RIM brand, but shall not include Third Party Software.
Aerosol coating product means a pressurized coating product containing pigments or resins that dispenses product ingredients by means of a propellant, and is packaged in a disposable can for hand-held application, or for use in specialized equipment for ground traffic/marking applications.
Radiation therapy simulation system means a radiographic or fluoroscopic x-ray system intended for localizing the volume to be exposed during radiation therapy and confirming the position and size of the therapeutic irradiation field.
Spectrum Compatibility means the capability of two (2) copper loop transmission system technologies to coexist in the same cable without service degradation and to operate satisfactorily in the presence of cross talk noise from each other. Spectrum compatibility is defined on a per twisted pair basis for specific well-defined transmission systems. For the purposes of issues regarding Spectrum Compatibility, service degradation means the failure to meet the Bit Error Ratio (BER) and Signal-to-Noise Ratio (SNR) margin requirements defined for the specific transmission system for all Loop lengths, model Loops, or loss values within the requirements for the specific transmission system.
Hemp products means all products made from industrial hemp,
Components means articles, materials, and supplies incorporated directly into end products at any level of manufacture, fabrication, or assembly by the Contractor or any subcontractor.
Fluoroscopic imaging assembly means a subsystem in which X-ray photons produce a visual image. It includes the image receptor(s) such as the image intensifier and spot-film device, electrical interlocks, if any, and structural material providing linkage between the image receptor and diagnostic source assembly.
Tobacco product manufacturer means an entity that after the date of enactment of this Act directly (and not exclusively through any affiliate):
Manufacturing Facilities means facilities engaged in the mechanical or chemical transformation of materials or substances into new products and shall include:
Weapons system supplier means any prime contractor or first tier subcontractor engaged in, or having a known prospective interest in the development, production or analysis of any of the weapon systems, as well as any major component or subassembly of such system.
Open-Source Components means any software component that is subject to any open-source copyright license agreement, including any GNU General Public License or GNU Library or Lesser Public License, or other obligation, restriction or license agreement that substantially conforms to the Open Source Definition as prescribed by the Open Source Initiative or otherwise may require disclosure or licensing to any third party of any source code with which such software component is used or compiled.
Analytical x-ray equipment means equipment used for x-ray diffraction or fluorescence analysis.
Diagnostic source assembly means the tube housing assembly with a beam-limiting device attached.
Sensor means any measurement device that is not part of the vehicle itself but installed to determine parameters other than the concentration of gaseous and particle pollutants and the exhaust mass flow.
Kit means a set of components that are packaged together and intended to be used to perform a specific in vitro diagnostic examination, or a part thereof;
Assay means a laboratory analysis of Crude Petroleum to include the following: A.P.I. Gravity, Reid vapor pressure, composition, pour point, water and sediment content, sulfur content, viscosity, distillation, hydrogen sulfide, flash/boiling point and other characteristics as may be required by Carrier.
Collaborative drug therapy management means participation by an authorized pharmacist and a physician in the management of drug therapy pursuant to a written community practice protocol or a written hospital practice protocol.
Manufacturing Site means a location where a manufacturing
HEPA filter means a high efficiency particulate absolute air filter capable of trapping and retaining 99.97 percent of fibers greater than 0.3 micrometers in mass median aerodynamic diameter equivalent.
Clone means a non-flowering plant cut from a mother plant that is capable of developing into a new plant and has shown no signs of flowering.
MSAA Indicator Technical Specifications document means, as the context requires, either or both of the document entitled “Multi-Sector Service Accountability Agreement (MSAA) 2019-20 Indicator Technical Specifications November 5, 2018 Version 1.3” and the document entitled “Multi-Sector Service Accountability Agreement (MSAA) 2019-20 Target and Corridor-Setting Guidelines” as they may be amended or replaced from time to time;
Manufacturing means all activities related to the manufacture of a Compound, including planning, purchasing, manufacture, processing, compounding, storage, filling, packaging, waste disposal, labeling, leafleting, testing, quality assurance, sample retention, stability testing, release, dispatch and supply, as applicable.
Aerosol product means a pressurized spray system that dispenses product ingredients by means of a propellant contained in a product or a product's container, or by means of a mechanically induced force. “Aerosol Product” does not include “Pump Spray.”
Biomarker means a parameter or characteristic in a patient or Patient Sample, the measurement of which is useful (a) for purposes of selecting appropriate therapies or patient populations or monitoring disease susceptibility, severity or state, or monitoring therapies for such patient and/or (b) for predicting the outcome of a particular treatment of such patient.
Remanufacturing means the activity of overhauling, retrofitting, fabricating, or repairing a product or its component parts for ultimate sale at retail.