Test interval definition

Test interval means a duration of time over which brake-specific emissions are determined. In cases where multiple test intervals occur over a duty cycle, the regulation may specify additional calculations that weigh and combine results to arrive at composite values for comparison against the applicable emission limits;
Sample 1Sample 2Sample 3
Test interval means a duration of time over which brake-specific emissions are determined;
Sample 1Sample 2Sample 3

Examples of Test interval in a sentence

  • Cardinal Health will invoice Acorda post completion of each Stability Test interval or as separately agreed for services provided under this Agreement.

  • This value of the Core Test interval shall be provided to upper layers.

  • Type:ValidDescription:Each Core Test interval shall have an identifier which shall be incremented by each start of a new test interval in background mode.

  • From the Setup Operations menu, you can configure passcode, alarms, fullscale, relays, faults, calibration interval, bump test interval, Line Integrity Test interval, date & time, network, pump control, location label, and display.

  • It was developed for the Canadian Center for Inland Waters and used by the University of Waterloo at Guelph.Nitrogen pressure source Data Acquisition system Bore hole Test interval Pressure Transducer PackerConstant head injection tanks Control panel Fig.

  • Test interval method of calculating Dairy Herd Improvement Association records.

  • Test interval spacing was at 20 cm (8 in.) for 10 positions below the 45-degree upper air vent where greater porosity was expected to be found.

  • Patient characteristics at baseline (t0) and patient status after the experimental period of HAT (t1) (n = 149)  Reported p-values are before Bonferroni-correction, and are based on Fisher's Exact Test (dichotomous variables) and non-parametric Kruskal-Wallis Test (interval variables).Table 2.

  • Upon completion of Supplier's System Integration Test interval, Company agrees to immediately begin to perform testing at Supplier's NOC facility located in Heathrow, Florida, on the Managed Service Node located at said facility, which is connected to Company's ITN, in order for Company to complete items********************** of Section 1.14.

  • The step response test (SRT) is started in AUTO mode regularly after the time entered in 'Test interval' has elapsed when the function is activated.

Related to Test interval

  • interval meter means a meter that measures and records electricity use on an hourly or sub-hourly basis;

  • Test cycle means a sequence of test points each with a defined speed and torque to be followed by the engine under steady state (WHSC) or transient operating conditions (WHTC).

  • Billing cycle or billing period means the period for which regular electricity bills as specified by the Commission, are prepared for different categories of consumers by the licensee;

  • Testing Period means a single period consisting of the four consecutive fiscal quarters of the Borrower then last ended (whether or not such quarters are all within the same fiscal year), except that if a particular provision of this Agreement indicates that a Testing Period shall be of a different specified duration, such Testing Period shall consist of the particular fiscal quarter or quarters then last ended that are so indicated in such provision.

  • Net metering period means the 12-month period following the date of final interconnection of the

  • Production Period is the period that for winter cereal advances commences October 1, 2021 and terminates September 30, 2023; for advances on all other field crops, honey, hogs, goats, sheep and lambs commences April 1, 2022 and terminates September 30, 2023; and for advances on cattle, continuous flow cattle, and bison commences on April 1, 2022 and terminates on March 31, 2024.

  • Operating Period for any Element of the Project shall mean the period from (and including) the COD of such Element of the Project, up to (and including) the Expiry Date and for the Project, shall mean the period from (and including) the COD of the Project, up to (and including) the Expiry Date;

  • Measurement Point means the emission source for which continuous emission measurement systems (CEMS) are used for emission measurement, or the cross-section of a pipeline system for which the CO2 flow is determined using continuous measurement systems;

  • Billing Period means (subject to Article 6.1 of the Agreement) the calendar month ending with the Metering Date. The first Billing Period shall commence from the Commercial Operation Date and end with the Metering Date corresponding to the month in which the Commercial Operation Date occurs.

  • INTER-CONNECTION POINT/ DELIVERY/ METERING POINT means a single point at 220kV or above, where the power from the Project(s) is injected into the identified ISTS Substation (including the dedicated transmission line connecting the Projects with the substation system) as specified in the RfS document. Metering shall be done at this interconnection point where the power is injected into. For interconnection with grid and metering, the WPDs shall abide by the relevant CERC/ SERC Regulations, Grid Code and Central Electricity Authority (Installation and Operation of Meters) Regulations, 2006 as amended and revised from time to time.

  • Baseline Period means the period used to determine the baseline emission rate for each regulated pollutant under OAR 340 division 222.

  • Meet-Point Billing (MPB means the billing associated with interconnection of facilities between two (2) or more LECs for the routing of traffic to and from an IXC with which one of the LECs does not have a direct connection. In a multi-bill environment, each Party bills the appropriate tariffed rate for its portion of a jointly provided Switched Exchange Access Service.

  • Calibration means the determination of (1) the response or reading of an instrument relative to a series of known radiation values over the range of the instrument, or (2) the strength of a source of radiation relative to a standard.

  • Quarterly (1/Quarter) sampling frequency means the sampling shall be done in the months of March, June, August, and December, unless specifically identified otherwise in the Effluent Limitations and Monitoring Requirements table.

  • Rolling Period means, as of any date, the four Fiscal Quarters ending on or immediately preceding such date.

  • Operating pressure means the pressure at which the parts of an irrigation system are designed by the manufacturer to operate.

  • Measurement means metered volumes at a custody transfer meter through a turbine, Coriolis, or such other meter.

  • Calibration gas means a gas mixture used to calibrate gas analysers.

  • Test means such test as is prescribed by the particulars or considered necessary by the Inspecting Officer whether performed or made by the Inspecting Officer or any agency acting under the direction of the Inspecting Officer;

  • Quarterly (1/Quarter) sampling frequency means the sampling shall be done in the months of March, June, August, and December, unless specifically identified otherwise in the Effluent Limitations and Monitoring Requirements table.

  • Plant Test Date or "PTD" means the date acceptance testing is performed with CLEC. "Point of Interface", "Point of Interconnection," or "POI" is a demarcation between the networks of two (2) LECs (including a LEC and CLEC). The POI is that point where the exchange of traffic takes place.

  • Contract Quarter means a three-month period that commences on January 1, April 1, July 1 or October 1 and ends on March 31, June 30, September 30, or December 31, respectively.

  • Test Date means, with respect to any Start Date, the last day of the most recent fiscal quarter of the Borrower ended immediately prior to such Start Date.

  • Maintenance Period shall have the meaning set forth in Clause 14.1; “Maintenance Requirements” shall have the meaning set forth in Clause 14.2;

  • Monitoring Period means the period from the Launch Date to the Valuation Date (both dates including) at such point in time at which the Reference Price of the Underlying is determined and published..

  • Meet-Point Billing (MPB) refers to the billing associated with interconnection of facilities between two or more LECs for the routing of traffic to and from an IXC with which one of the LECs does not have a direct connection. In a multi-bill environment, each Party bills the appropriate tariffed rate for its portion of a jointly provided Switched Exchange Access Service.