Total resistance definition

Total resistance means the total force resisting movement of a vehicle, including the frictional forces in the drivetrain.
Sample 1Sample 2Sample 3
Total resistance means the total force resisting movement of a vehicle, including the fric- tional forces in the drive-train; [“Vehicle coastdown mode” means a special mode of operation, for example by decoupling drivetrain components from the wheels mechanically and/or electrically, enabling an accurate and repeatable road load determination and an accurate dynamometer setting];
Sample 1
Total resistance means the total force resisting movement of a vehicle, including the frictional forces in the drive-train;
Sample 1

Examples of Total resistance in a sentence

  • Etotal = E1 = E2 = En• Total resistance in a parallel circuit is less than any of the individual resistances.

  • Itotal = I1 = I2 = In• Total resistance in a series circuit is equal to the sum of the individual resistances, mak- ing it greater than any of the individual resistances.

  • Total resistance was well predicted, but the individual contributions showed some (serious) deviations.

  • Total resistance of continuity conductor should be less than 1 ohms.c. Earthing lead can be of GI/Copper Strip.

  • Total resistance for the winding was found 175.88 Ω and 175.7 Ω respectively for 4 and 7-section model.

  • Literature (21, 22, 23, 24) lists the properties of special importance for paving applications, along with the fundamental response parameters, as: • Rigidity: Total resistance to deformation.

  • Location / Station - Check for its actual & its comparison with drawings - Resistance of each individual anode - Current dissipation by each individual anode at different likely voltage - Total resistance of complete anode bed.

  • The input data are: Chip temperature (T9), Total resistance (R), Inlet cooling water temperature (T10), Approaching temperature of evaporator or difference in temperature from chip to evaporator (∆T1), Approaching temperature of absorber (∆T2), Approaching temperature of condenser (∆T3), Approaching temperature of generator (∆T4), evaporator wall superheat (∆TWSe), generator wall superheat (∆TWSg)and Concentration difference (∆X).

  • Total resistance comparison including possible im- provement by adapted bulbous bow Similar to the improvements in the wave making resistance, the largest reduction of total resistance could be achieved for bow-up trim angles.

  • Total resistance of joint (kN/m) is calculated as follows: VRd.joint = nRVL x VRd (kN/m)nRVL = number of RVL wire rope loops / meter.

Related to Total resistance

  • Total resource cost test or "TRC test" means a standard that is met if, for an investment in energy efficiency or demand-response measures, the benefit-cost ratio is greater than one. The benefit-cost ratio is the ratio of the net present value of the total benefits of the program to the net present value of the total costs as calculated over the lifetime of the measures. A total resource cost test compares the sum of avoided electric utility costs, representing the benefits that accrue to the system and the participant in the delivery of those efficiency measures, as well as other quantifiable societal benefits, including avoided natural gas utility costs, to the sum of all incremental costs of end-use measures that are implemented due to the program (including both utility and participant contributions), plus costs to administer, deliver, and evaluate each demand-side program, to quantify the net savings obtained by substituting the demand-side program for supply resources. In calculating avoided costs of power and energy that an electric utility would otherwise have had to acquire, reasonable estimates shall be included of financial costs likely to be imposed by future regulations and legislation on emissions of greenhouse gases.

  • Soft drinks means nonalcoholic beverages that contain natural or artificial sweeteners. "Soft drinks" does not include beverages that contain milk or milk products, soy, rice, or similar milk substitutes, or that contains greater than fifty per cent vegetable or fruit juice by volume.

  • Comprehensive Plan means a generalized, coordinated land use map and policy statement of the governing body of a local government that interrelates all functional and natural systems and activities relating to the use of lands, including but not limited to sewer and water systems, trans- portation systems, educational facilities, recreational facilities, and natural resources and air and water quality management programs. “Comprehensive” means all-inclusive, both in terms of the geographic area covered and functional and natural activities and systems occurring in the area covered by the plan. “General nature” means a summary of policies and proposals in broad catego- ries and does not necessarily indicate specific locations of any area, activity or use. A plan is “co- ordinated” when the needs of all levels of governments, semipublic and private agencies and the citizens of Oregon have been considered and accommodated as much as possible. “Land” includes water, both surface and subsurface, and the air.