We use cookies on our site to analyze traffic, enhance your experience, and provide you with tailored content.

For more information visit our privacy policy.

Ultimate tensile strength definition

Ultimate tensile strength means the greatest amount of load applied to a bungee cord prior to failure.
Ultimate tensile strength means the point when the applied load reaches a maximum prior to failure, expressed in pounds.
Ultimate tensile strength means the maximum tensile stress that a material can sustain under uni-axial tension, calculated on the basis of the load at rupture and the original unstrained dimensions.

Examples of Ultimate tensile strength in a sentence

  • Ultimate tensile strength (UTS) for a fully cured polyester resin given by the supplier is 40 MPa, although it is clearly stated that this is neither a minimum nor a maximum for the material due to potential variations in preparation.

  • The soil reinforcement type, Minimum Average Roll Value of the Ultimate tensile strength TULT (MARV) for geosynthetic soil reinforcement, spacing, lengths, elevations, and the corresponding wall design height shall be shown on the shop drawings.

  • The formula for determining MAWP is as follows: TStE = MAWP, PSIG RFS‌ Where:TS = Ultimate tensile strength of shell plates, PSIR = Inside radius of the weakest course of the shell or drum, inches.

  • Type : Aluminium conductor steel reinforced.Code Name : Mink/Fox-see Bill of Quantities/drawingsMass : 85kg/km / 149kg/km Ultimate tensile strength : 7 900 / 13 200 NewtonMax working tension : @ -5oC + wind 5 240 / 8760 Newton.

  • Bracket should be made of corrosion resistant alluminium alloy.λ Ultimate tensile strength of the clamp should not be less than 15 KN for 50/70 sq.mm.

  • Ultimate tensile strength of base metal and surface composites fabricated via multi-pass FSP.

  • The material properties shall be as follows:- Ultimate tensile strength: minimum 200 N/mm2 0.2% Proof Stress: minimum 185 N/mm2.

  • Sut = Ultimate tensile strength = 200 N/mm2¥ì = Poisson.s Ratio for the cylinder material = 0.29 (std.) di = Inner diameter of cylinder = 50mmConsider,Double acting cylinder 50 X 50 (Diameter X Stroke) [ ri =25 mm ]By assuming pressure in working cylinder is, P = 6 bar =0.6 N/mm2 So according to Clavarino’s equation,For closed end cylinder at both ends to determine the thickness of cylinder.

  • The soil reinforcement type, Minimum Average Roll Value of the Ultimate tensile strength, TULT (MARV), for geosynthetic soil reinforcement or yield strength for metallic soil reinforcement, spacing, lengths, elevations, and the corresponding wall design height segments shall be shown on the shop drawings.

  • Ultimate tensile strength decreased sharply and then stabilised as water content increased.

Related to Ultimate tensile strength

  • Strength means a feature or aspect of the SOQ that exceeds the minimum requirements of the RFQ and increases the chance of successful Contract performance. A significant Strength in the SOQ is a feature or aspect that exceeds the minimum requirements of the RFQ and increases the chance of successful Contract performance.

  • Stinger-steered automobile or watercraft transporter means an automobile or watercraft transporter

  • Satellite Manufacturer means, with respect to any Satellite, the prime contractor and manufacturer of such Satellite.

  • LOCKHEED XXXXXX Procurement Representative means a person authorized by LOCKHEED XXXXXX'x cognizant procurement organization to administer and/or execute this Contract.

  • EPG means electronic program guide maintained by a DPO on its Digital Distribution Platform which lists the television channels and programs, and scheduling and programming information therein and includes any enhanced electronic guide that allows Subscribers to navigate and select such available channels and programs.

  • urge buckslip optional, but recommended. (This is a small, single sheet of paper that requests Customers to vote as quickly as possible and that their vote is important. One copy will be supplied by the Fund.)

  • Intensive supervision program means a parole program that

  • Project Management Plan means the portion of the Project Development Plan providing the information requested in Section 4.2 of Exhibit B to the ITP.

  • Medical Child Support Order means any judgment, decree or order (including approval of a domestic relations settlement agreement) issued by a court of competent jurisdiction that:

  • Engine Manufacturer means CFM International, Inc.

  • Nutrient management plan means a plan developed or approved by the Department of Conservation and Recreation that requires proper storage, treatment and management of poultry waste, including dry litter, and limits accumulation of excess nutrients in soils and leaching or discharge of nutrients into state waters.

  • Basic Comprehensive User Guide means the Ministry document titled Basic Comprehensive Certificates of Approval (Air) User Guide” dated April 2004 as amended.

  • Transit-oriented development means infrastructure improvements that are located within 1/2 mile of a transit station or transit-oriented facility that promotes transit ridership or passenger rail use as determined by the board and approved by the municipality in which it is located.

  • Single Phase Aerosol Air Freshener means an aerosol air freshener with the liquid contents in a single homogeneous phase and which does not require that the product container be shaken before use.

  • LOCKHEED MARTIN Procurement Representative means a person authorized by LOCKHEED MARTIN's cognizant procurement organization to administer and/or execute this Contract.

  • Peer support specialist means an individual who has experienced a severe and persistent mental illness and who has successfully completed standardized training to provide peer support services through the medical assistance program or the Iowa Behavioral Health Care Plan.

  • Environmental Management Framework and “EMF” mean the framework of the Borrower for the management of social and environmental aspects of the Project dated April 24, 2007 and disclosed to the public on even date therewith, as may be amended from time to time with the prior approval of the Bank.

  • Flexible vinyl adhesive means an aerosol adhesive designed to bond flexible vinyl to substrates. Flexible vinyl means a nonrigid polyvinyl chloride plastic with at least five percent, by weight, of plasticizer content. A plasticizer is a material, such as a high boiling point organic solvent, that is incorporated into a vinyl to increase its flexibility, workability, or distensibility, and may be determined using ASTM Method E260-91 or from product formulation data.

  • Specialist medical practitioner means a specialist as defined in section 3 of the Health Insurance Act 1973.

  • FIRM PROCUREMENT means the agreement between the parties for mutually agreed terms and conditions with commitment of Quantity Ordered.

  • High voltage bus means the electrical circuit, including the coupling system for charging the REESS that operates on a high voltage.

  • Planned External Financed Generation Capacity Resource means a Planned External Generation Capacity Resource that, prior to August 7, 2015, has an effective agreement that is the equivalent of an Interconnection Service Agreement, has submitted to the Office of the Interconnection the appropriate certification attesting achievement of Financial Close, and has secured at least 50 percent of the MWs of firm transmission service required to qualify such resource under the deliverability requirements of the Reliability Assurance Agreement.

  • Flashpoint means the minimum temperature at which a liquid gives off a vapor in sufficient concentration to ignite when tested as follows:

  • Organ procurement organization means a person designated by the Secretary of the United States Department of Health and Human Services as an organ procurement organization.

  • Quality Management Plan means the portion of the Project Development Plan providing the information requested in Section 4.3 of Exhibit B to the ITP.

  • Procurement Management means the Director of Lee County’s Procurement Management Department or designee.