Billing Method 2.6.1 To receive payment for services rendered pursuant to this contract the Contractor shall submit a fully completed invoice for work previously performed to:
2.6.2 At a minimum, the invoice shall detail the following information:
2.6.2.1 Unique invoice number;
2.6.2.2 Contractor’s name, address, and telephone number;
2.6.2.3 Date of invoice and/or billing period;
2.6.2.4 Applicable Contract No.;
Average Log Length and Payment Reduction If the average log length for all logs delivered under this contract is less than the average log length specified in the table in clause G-024.2, The amount of allowable payment reduction shall be calculated by multiplying the payment rate in P-028.2 by the total volume delivered, and the difference between the average length of logs delivered and the average log length specified in G-024.2, times 1% as follows: Log Length Payment Reduction = (B x V x L) x (.01) Where: B = Bid rate from P-028.2 clause V = total delivered log Volume L = Length in feet below specified average (rounded to nearest Average log length payment reductions calculated by the Purchaser must be approved by the State, prior to payment for the final billing period. Third-party scaling organization information is required to determine Xxxxxxxx mbf and Average log length for payment reduction purposes. Average log length is determined on a piece count basis. Value of log length price reduction will be derived from the applicable sort value as described in this contract. Scale information for determining Average log length for payment reduction eligibility must be obtained from roll-out scale. Truck-ramp, sample scaling, and/or bundle scaling information is not acceptable for determining eligibility. Purchaser’s exclusive remedy for below average log lengths shall be the payment reduction described in this clause, notwithstanding other provisions in the Uniform Commercial Code.
Failed or Returned Payment Instructions In using the Service, you are requesting that we or our Service Provider attempt to make payments for you from your Eligible Transaction Account. If the Payment Instruction cannot be completed for any reason associated with your Eligible Transaction Account (for example, there are insufficient funds in your Eligible Transaction Account, or the Payment Instruction would exceed the credit or overdraft protection limit of your Eligible Transaction Account, to cover the payment), the Payment Instruction may or may not be completed. In certain circumstances, our Service Provider may either advance funds drawn on their corporate account or via an electronic debit, and in such circumstances will attempt to debit the Eligible Transaction Account a second time to complete the Payment Instruction. In some instances, you will receive a return notice from us or our Service Provider. In each such case, you agree that:
a. You will reimburse our Service Provider immediately upon demand the amount of the Payment Instruction if the payment has been delivered but there are insufficient funds in, or insufficient overdraft credits associated with, your Eligible Transaction Account to allow the debit processing to be completed;
b. You may be assessed a late fee equal to one and a half percent (1.5%) of any unpaid amounts plus costs of collection by our Service Provider or their third-party contractor if the Payment Instruction cannot be debited because you have insufficient funds in your Eligible Transaction Account, or the transaction would exceed the credit or overdraft protection limit of your Eligible Transaction Account, to cover the payment, or if the funds cannot otherwise be collected from you. The aforesaid amounts will be charged in addition to any NSF charges that may be assessed by us, as set forth in your fee schedule from us (including as disclosed on the Site) or your account agreement with us. You hereby authorize us and our Service Provider to deduct all of these amounts from your designated Eligible Transaction Account, including by ACH debit;
c. Service Provider is authorized to report the facts concerning the return to any credit reporting agency.
Accounting Method For both financial and tax reporting purposes, the books and records of the Company shall be kept on the accrual method of accounting applied in a consistent manner and shall reflect all Company transactions and be appropriate and adequate for the Company’s business.
Payment Methodology The Contractor shall be compensated based on the Service Rates in Attachment for units of service authorized by the Institution in a total amount not to exceed the Contract Maximum Liability established in Section C.
1. The Contractor’s compensation shall be contingent upon the satisfactory completion of units of service or project milestones identified in Attachment B. The Contractor shall submit invoices, in form and substance acceptable to the Institution with all of the necessary supporting documentation, prior to any payment. Such invoices shall be submitted for completed units of service or project milestones for the amount stipulated.
Change in Accounting Method Neither Company nor any of its Subsidiaries has agreed to make, nor is it required to make, any material adjustment under Section 481(a) of the Code or any comparable provision of state, local, or foreign Tax Laws by reason of a change in accounting method or otherwise.
Voting Method Unless otherwise provided by law, when a vote is taken upon any measure before the Board, with a quorum being present, a majority of the votes cast shall determine its outcome. A vote of "abstain" or "present," or a vote other than "yea" or "nay," or a failure to vote, is counted for the purposes of determining whether a quorum is present. A vote of "abstain" or "present," or a vote other than "yea" or "nay," or a failure to vote, however, is not counted in determining whether a measure has been passed by the Board, unless otherwise stated in law. The sequence for casting votes is rotated. On all questions involving the expenditure of money and on all questions involving the closing of a meeting to the public, a roll call vote shall be taken and entered in the Board's minutes. An individual Board member may request that a roll call vote be taken on any other matter; the President or other presiding officer may approve or deny the request but a denial is subject to being overturned by a majority vote of the members present. Any Board member may request that his or her vote be changed before the President announces the result. Any Board member may include a written explanation of his or her vote in the District file containing individual Board member statements; the explanation will not be part of the minutes. The Board Secretary shall keep written minutes of all Board meetings (whether open or closed), which shall be signed by the President and the Secretary. The minutes include:
Payment Method Payment shall be made by the Contractor to the Subcontractor as follows: (choose one) ☐ - Immediately upon completion of the Services to the satisfaction of the Contractor. ☐ - Within ____ business days after completion of the Services to the satisfaction of the Contractor. ☐ - Shall be paid on a ☐ weekly ☐ monthly ☐ quarterly ☐ other ______________________ basis. If the Subcontractor completes the Services to the satisfaction of the Contractor, before the full amount or balance has been fully paid, any remaining amount shall be payable immediately. ☐ - Other: ________________________________________________________
Measurement method An isolation resistance test instrument is connected between the live parts and the electrical chassis. The isolation resistance is subsequently measured by applying a DC voltage at least half of the working voltage of the high voltage bus. If the system has several voltage ranges (e.g. because of boost converter) in conductively connected circuit and some of the components cannot withstand the working voltage of the entire circuit, the isolation resistance between those components and the electrical chassis can be measured separately by applying at least half of their own working voltage with those components disconnected.
Test method This test is intended to demonstrate the immunity of the vehicle electronic systems. The vehicle shall be subject to electromagnetic fields as described in this annex. The vehicle shall be monitored during the tests. If not otherwise stated in this annex the test shall be performed according to ISO 11451-2.
