Average Log Length and Payment Reduction. If the average log length for all logs delivered under this contract is less than the average log length specified in the table in clause G-024.2, The amount of allowable payment reduction shall be calculated by multiplying the payment rate in P-028.2 by the total volume delivered, and the difference between the average length of logs delivered and the average log length specified in G-024.2, times 1% as follows: Log Length Payment Reduction = (B x V x L) x (.01) 1/10th) Where: B = Bid rate from P-028.2 clause V = total delivered log Volume L = Length in feet below specified average (rounded to nearest Average log length payment reductions calculated by the Purchaser must be approved by the State, prior to payment for the final billing period. Third-party scaling organization information is required to determine Xxxxxxxx mbf and Average log length for payment reduction purposes. Average log length is determined on a piece count basis. Value of log length price reduction will be derived from the applicable sort value as described in this contract. Scale information for determining Average log length for payment reduction eligibility must be obtained from roll-out scale. Truck-ramp, sample scaling, and/or bundle scaling information is not acceptable for determining eligibility. Purchaser’s exclusive remedy for below average log lengths shall be the payment reduction described in this clause, notwithstanding other provisions in the Uniform Commercial Code.
Average Log Length and Payment Reduction. If the average log length for all logs delivered under this contract is less than the average log length specified in the table in clause G-024.2, The amount of allowable payment reduction shall be calculated by multiplying the payment rate in P-028.2 by the total volume delivered, and the difference between the average length of logs delivered and the average log length specified in G-024.2, times 1% as follows: Log Length Payment Reduction = (B x V x L) x (.01) 1/10th) Where:
Average Log Length and Payment Reduction. If the average log length for all logs delivered under this contract is less than the average log length specified in the table in clause G-024.2, The amount of allowable payment reduction shall be calculated by multiplying the payment rate in P-028.2 by the total volume delivered, and the difference between the average length of logs delivered and the average log length specified in G-024.2, times 1% as follows: Log Length Payment Reduction = (B x V x L) x (.01) 1/10th) Where: B = Bid rate from P-028.2 clause V = total delivered log Volume L = Length in feet below specified average (rounded to nearest Third party scaling organization information is required to determine Xxxxxxxx mbf and Average log length for payment reduction purposes. Average log length is determined on a piece count basis. Value of log length price reduction will be derived from the applicable sort value as described in this contract. Scale information for determining Average log length for payment reduction eligibility must be obtained from roll-out scale. Truck-ramp and/or bundle scaling information is not acceptable for determining eligibility. Purchaser’s exclusive remedy for below average log lengths shall be the payment reduction described in this clause, notwithstanding other provisions in the Uniform Commercial Code.
Average Log Length and Payment Reduction. If the average log length for all logs delivered under this contract is less than the average log length specified in the table in clause G-024.2, The amount of allowable payment reduction shall be calculated by multiplying the payment rate in P-028.2 by the total volume delivered, and the difference between the average length of logs delivered and the average log length specified in G-024.2, times 1% as follows: Log Length Payment Reduction = (B x V x L) x (.01) 1/10th) Where: B = Bid rate from P-028.2 clause V = total delivered log Volume L = Length in feet below specified average (rounded to nearest Average log length payment reductions calculated by the Purchaser must be approved by the State, prior to payment for the final billing period. Third-party scaling organization information is required to determine Xxxxxxxx mbf and Average log length for payment reduction purposes. Average log length is determined on a piece count basis. Value of log length price reduction will be derived from the applicable sort value as described in this contract. Scale information for determining Average log length for payment reduction eligibility must be obtained from roll-out scale. Truck-ramp, sample scaling, and/or bundle scaling information is not acceptable for determining eligibility. Purchaser’s exclusive remedy for below average log lengths shall be the payment reduction described in this clause, notwithstanding other provisions in the Uniform Commercial Code. P-039.2 Tonnage Sort Payment Reduction Requirements Purchaser must provide a plan in writing, acceptable to the State, to acquire third party Xxxxxxxx mbf scaling information in order to be eligible for a payment reduction for a tonnage sort according to clauses P-036.2 or P-037.2. Logs delivered and accepted by the Purchaser prior to the State’s acceptance of Purchaser’s written payment reduction plan are not eligible for payment reduction. Failure of Purchaser to provide sample scale data in a timely, accurate and legible basis will void an approved sample scale plan. An approved payment reduction plan can be voided at the sole discretion of the State. For the purpose of tonnage sort payment reduction requests, preferred log lengths for tonnage sawlog sorts shall include the following plus any additional lengths identified in clause G-024.2: Species Type Preferred Lengths Conifer Sorts 16’, 20’, 24’, 26’, 32’, 40’ Hardwood Sorts 18’, 20’, 26’, 28’, 30’, 36’, 38’, 40’
