Reactive Power and Primary Frequency Response 9.6.1 Power Factor Design Criteria
Emergency Plan LIDDA shall develop and maintain an Emergency Plan as prescribed in section 2.10.6 Attachment A-1, Statement of Work.
Primary Frequency Response Developer shall ensure the primary frequency response capability of its Large Generating Facility by installing, maintaining, and operating a functioning governor or equivalent controls. The term “functioning governor or equivalent controls” as used herein shall mean the required hardware and/or software that provides frequency responsive real power control with the ability to sense changes in system frequency and autonomously adjust the Large Generating Facility’s real power output in accordance with the droop and deadband parameters and in the direction needed to correct frequency deviations. Developer is required to install a governor or equivalent controls with the capability of operating: (1) with a maximum 5 percent droop ± 0.036 Hz deadband; or (2) in accordance with the relevant droop, deadband, and timely and sustained response settings from an approved Applicable Reliability Standard providing for equivalent or more stringent parameters. The droop characteristic shall be: (1) based on the nameplate capacity of the Large Generating Facility, and shall be linear in the range of frequencies between 59 and 61 Hz that are outside of the deadband parameter; or (2) based on an approved Applicable Reliability Standard providing for an equivalent or more stringent parameter. The deadband parameter shall be: the range of frequencies above and below nominal (60 Hz) in which the governor or equivalent controls is not expected to adjust the Large Generating Facility’s real power output in response to frequency deviations. The deadband shall be implemented: (1) without a step to the droop curve, that is, once the frequency deviation exceeds the deadband parameter, the expected change in the Large Generating Facility’s real power output in response to frequency deviations shall start from zero and then increase (for under-frequency deviations) or decrease (for over-frequency deviations) linearly in proportion to the magnitude of the frequency deviation; or (2) in accordance with an approved Applicable Reliability Standard providing for an equivalent or more stringent parameter. Developer shall notify NYISO that the primary frequency response capability of the Large Generating Facility has been tested and confirmed during commissioning. Once Developer has synchronized the Large Generating Facility with the New York State Transmission System, Developer shall operate the Large Generating Facility consistent with the provisions specified in Articles 9.5.5.1 and 9.5.5.2 of this Agreement. The primary frequency response requirements contained herein shall apply to both synchronous and non-synchronous Large Generating Facilities.
ATM Safety It is important to be aware of your surroundings when using an ATM, especially at night. When you are using an ATM, you should secure any cash you withdraw before leaving the ATM. If you need to use an ATM at night, consider taking someone you know with you, and only use an ATM that is well-lit and unobstructed from view. If anything appears to be suspicious, do not use the ATM. Always call 911 in the event of an emergency or to report any suspicious activity. If you have any questions or comments about the safety of any of our ATMs, please call us on Oahu at (000) 000-0000 or 0-000-000-0000 from the neighbor islands, Guam, the CNMI or Continental U.S.
Access to Network Interface Device (NID 2.4.3.1. Due to the wide variety of NIDs utilized by BellSouth (based on subscriber size and environmental considerations), Mpower may access the on-premises wiring by any of the following means: BellSouth shall allow Mpower to connect its loops directly to BellSouth’s multi-line residential NID enclosures that have additional space and are not used by BellSouth or any other telecommunications carriers to provide service to the premise. Mpower agrees to install compatible protectors and test jacks and to maintain the protection system and equipment and to indemnify BellSouth pursuant to Section 8 of the General Terms and Conditions of this Agreement.
COVID-19 Protocols Contractor will abide by all applicable COVID-19 protocols set forth in the District’s Reopening and COVID-19 Mitigation Plan and the safety guidelines for COVID-19 prevention established by the California Department of Public Health and the Ventura County Department of Public Health.
Internet Safety X. Xxxxxxx and Users - Despite every effort for supervision and filtering, all Users and their parents/guardians are advised that access to the electronic Network may include the potential for access to materials inappropriate for school-aged students. Every User must take responsibility for his or her use of the Network and Internet and avoid these sites.
Contingency Plan Contractor is aware that unforeseen circumstances, Including damage to their Facility(ies), equipment breakdowns, weather-related emergencies and other Force Majeur events, may require their participation in non-scheduled operations in order to provide continuous service to the public. Contractor hereby acknowledges that, under this Agreement, they are prepared to commit to participation in training for such emergency scenarios and to provide vehicles and personnel to maintain uninterrupted service during impairment or breakdown of Contractor’s Facility or equipment, and in case of natural disaster or other emergency, Including the events described in Section 14.09.
Technical Standards Applicable to a Wind Generating Plant i. Low Voltage Ride-Through (LVRT) Capability A wind generating plant shall be able to remain online during voltage disturbances up to the time periods and associated voltage levels set forth in the standard below. The LVRT standard provides for a transition period standard and a post-transition period standard.
Product Safety Seller must maintain the state of the product so that it is able to perform to its designed or intended purpose without causing unacceptable risk of harm to a person or damage to property.
