Processes Any employer, employee, trade union or employer’s association may at any point in time apply for an exemption from any of the provisions of this Collective Agreement. The applicant is required to complete and submit in writing with the relevant office of the Council, a fully and properly completed prescribed application for exemption form, accompanied by all relevant supporting documentation.
Firmware The Contractor shall deliver firmware required for production acceptance testing in accordance with CDRL A009 Contractor’s Supplier Configuration Management Plan. The Contractor shall use Government furnished software for testing. Deliverable Data Item (See DD-1423): CDRL A009: “Contractor’s Supplier Configuration Management Plan”
Protocols Each party hereby agrees that the inclusion of additional protocols may be required to make this Agreement specific. All such protocols shall be negotiated, determined and agreed upon by both parties hereto.
For Product Development Projects and Project Demonstrations Published documents, including date, title, and periodical name. Estimated or actual energy and cost savings, and estimated statewide energy savings once market potential has been realized. Identify all assumptions used in the estimates. Greenhouse gas and criteria emissions reductions. Other non-energy benefits such as reliability, public safety, lower operational cost, environmental improvement, indoor environmental quality, and societal benefits. Data on potential job creation, market potential, economic development, and increased state revenue as a result of the project. A discussion of project product downloads from websites, and publications in technical journals. A comparison of project expectations and performance. Discuss whether the goals and objectives of the Agreement have been met and what improvements are needed, if any.
Use of Technology Participants are subject to all existing laws (federal and state) and University regulations and policies on use of technology, including not only those laws and regulations that are specific to computers and networks, but also those that may apply generally to personal conduct such as: UC Electronic Communications Policy: xxxx://xxxxxx.xxxx.xxx/doc/7000470/ElectronicCommunications UCLA E-mail Policy and Guidelines: xxxx://xxx.xxxxxxxxxxxxx.xxxx.xxx/app/Default.aspx?&id=455 IT Services Acceptable Use Policy: xxxx://xxx.xxx.xxxx.xxx/policies/aupdetail.html The UC Policy on Copyright Ownership: xxxx://xxxxxxxxx.xxxxxxxxxxxxxxxxxxxxxx.xxx/resources/copyright-ownership.html Bruin OnLine Service Level Agreement: xxxx://xxx.xxx.xxxx.xxx/policies/BOL_SLA.pdf Any violation may result in technology related privileges being restricted or revoked and may also result in The University undertaking disciplinary or civil action. If the violation constitutes a criminal offense, appropriate legal action may be taken.
Models The Purchaser acknowledges that the model homes, if any, are for display purposes only, and that some or all of the features contained therein may not be included in the Dwelling unless same is specifically provided for in any schedule forming part of this Agreement. The Purchaser acknowledges and accepts that the Vendor will be maintaining the model home or homes or sales offices and all advertising signs associated therewith for sale purposes until all homes in this subdivision and/or the adjacent subdivisions built by the Vendor or its affiliated corporations have been constructed, sold and occupied. The Purchaser acknowledges that the lot dimensions illustrated on the proposed plan of subdivision (if not registered) are approximate and may be varied in accordance with the requirements of the Vendor or the Municipality. The Purchaser further acknowledges that the lot dimensions illustrated on various plans, brochures or other marketing materials displayed in the sales office or elsewhere are approximate and it is suggested that the Purchaser refer to the actual dimensions of the subject lot as noted on the proposed plan of subdivision subject to the foregoing. The Purchaser acknowledges that if the Property being purchased herein has been used by the Vendor as a model home or inventory to the Vendor, then there will be wear and tear in the Property which the Purchaser accepts and the Purchaser acknowledges that he/she is purchasing this Property on an “as is” basis including without limiting the generality thereof existing nicks, dents, scratches, scuff marks on all hardwood areas, stairs, pickets, xxxxxxxx, risers, treads, all trim work doors, jambs, baseboards/casings, wear and tear on carpet, existing paint touch-up blemishes, existing chips and scratches on ceramics and grout areas, wear and tear and scuff marks on all counters and tubs and agrees that the Vendor shall not be responsible either directly or indirectly (including by way of claim pursuant to the legislation relating to the Tarion warranties) to clean, repair or replace any part of the Property including wall covering, carpeting, vinyl/ceramic/hardwood flooring, cabinetry, window treatments, trees, shrubs or other planting materials, interlocking walkways and/or slab walkways, or any other features or extras on the Property either before or after closing unless specifically set out in this Agreement of Purchase and Sale. The Purchaser acknowledges that the life time line of the exterior brick work, shingles, windows and doors seals commenced at the time the model home was built and the Builder’s warranties have expired and the Builder’s warranties on the air conditioner and humidifier ( Mechanical Units) have expired and agrees that the Vendor shall not be responsible either directly or indirectly (including by way of claim pursuant to the legislation relating to the Tarion warranties) for any warranty claim for same. All appliances, including but not limited to the air conditioner and humidifiers (Mechanical Units), and fixtures included in the purchase price are purchased in an “as is” condition.
Software Title and ownership to Existing Software Product(s) delivered by Contractor under the Contract that is normally commercially distributed on a license basis by the Contractor or other independent software vendor proprietary owner (“Existing Licensed Product”), embedded in the Custom Products, shall remain with Contractor or the proprietary owner of other independent software vendor(s) (ISV). Effective upon acceptance, such Product shall be licensed to Authorized User in accordance with the Contractor or ISV owner’s standard license agreement, provided, however, that such standard license, must, at a minimum: (a) grant Authorized User a non-exclusive, perpetual license to use, execute, reproduce, display, perform, adapt (unless Contractor advises Authorized User as part of Contractor’s proposal that adaptation will violate existing agreements or statutes and Contractor demonstrates such to the Authorized User’s satisfaction) and distribute Existing Licensed Product to the Authorized User up to the license capacity stated in the Purchase Order or work order with all license rights necessary to fully effect the general business purpose(s) stated in the Bid or Authorized User’s Purchase Order or work order, including the financing assignment rights set forth in paragraph (c) below; and (b) recognize the State of New York as the licensee where the Authorized User is a state agency, department, board, commission, office or institution. Where these rights are not otherwise covered by the ISV’s owner’s standard license agreement, the Contractor shall be responsible for obtaining these rights at its sole cost and expense. The Authorized User shall reproduce all copyright notices and any other legend of ownership on any copies authorized under this clause. Open source software is developed independently of Contractor and may be governed by a separate license (“open source software”). If the open source software is governed by a separate License and provided under this Contract, Contractor shall provide a copy of that license in the applicable Documentation and the Authorized User's license rights and obligations with respect to that open source software shall be defined by those separate license terms and subject to the conditions, if any, therein. Nothing in this Contract shall restrict, limit, or otherwise affect any rights or obligations the Authorized User may have, or conditions to which the Authorized User may be subject, under such separate open source license terms.
Manufacturing (a) The Supplier shall without limitation be responsible, at no additional cost to the Purchaser, for: sourcing and procuring all raw materials for the Products; obtaining all necessary approvals, permits and licenses for the manufacturing of the Products; providing sufficient qualified staff and workers to perform the obligations under this Purchase Agreement; implementing and maintaining effective inventory and production control procedures with respect to the Products; and handling other matters as reasonably requested by the Purchaser from time to time.
Technology Discoveries, innovations, Know-How and inventions, whether patentable or not, including computer software, recognized under U.S. law as intellectual creations to which rights of ownership accrue, including, but not limited to, patents, trade secrets, maskworks and copyrights developed under this Agreement.
Architecture The Private Improvements shall have architectural features, detailing, and design elements in accordance with the Project Schematic Drawings. All accessory screening walls or fences, if necessary, shall use similar primary material, color, and detailing as on the Private Improvements.
