Delivery Point The delivery point is the point of delivery of the Power Product to the CAISO Controlled Grid (the “Delivery Point”). Seller shall provide and convey to Buyer the Power Product from the Generating Facility at the Delivery Point. Title to and risk of loss related to the Power Product transfer from Seller to Buyer at the Delivery Point.
Delivery Points Project water made available to the Agency pursuant to Article 6 shall be delivered to the Agency by the State at the delivery structures established in accordance with Article 10.
Aircraft This peril includes self-propelled missiles and spacecraft.
Fuel The Vehicle must be returned with the amount of fuel equal to that at the time of the commencement of the rental. If the Vehicle is returned with less fuel, the difference will be charged to You at a rate of $5.00 per litre (which includes a service component).
Water Supply The system may or may not meet state and local requirements. It is the right and responsibility of Buyer to determine the compliance of the system with state and local requirements. [For additional information on this subject, request the “Water Supply and Waste Disposal Notification” form.]
Fleet In general, any in-house mechanic may be assigned to respond to any emergency during normal working hours in any of the three operating companies. (This does not supersede the Mechanic Personnel Working Across 309 Jurisdictional Boundaries Agreement dated October 4, 2007). Example 1: Lincoln (CILCO) unit breaks down in the northern part of its territory. It would make sense for the Bloomington (rp) mechanic to respond to the service call. Lincoln staffs a 2nd shift mechanic only and the vehicle in need of repair is closer to the Bloomington garage. This example covers areas that both have Ameren in-house mechanics. Example 2: Any CIPS 702 units could be repaired by Ameren staffed mechanics in 702 territories. This would generally happen in areas that are in close proximity to an IP or CILCO garage. This example covers 702 CIPS areas that do not have Ameren in-house mechanics. These jobs currently are outsourced. Perform Preventive Maintenance on CIPS 702 equipment at individual operating centers where advantageous. This work is currently outsourced. It is not the company’s intent to perform all PM’s with in-house mechanics.
Flight Crew (a) Lessor shall employ or engage and pay all salaries, benefits and and/or compensation for a fully-qualified flight crew with appropriate credentials to conduct each flight undertaken under this Agreement. Lessor may use temporary flight crewmembers for a flight under this Agreement only if any such temporary crewmember is FlightSafety (or SimuFlite) trained, is current on the Aircraft and satisfies all of the requirements and conditions under the insurance coverage for the Aircraft. All flight crewmembers shall be included on any insurance policies that Lessor is required to maintain hereunder. (b) The qualified flight crew provided by Lessor shall exercise all of its duties and responsibilities with regard to the safety of each flight conducted hereunder in accordance with applicable FAR’s. The Aircraft shall be operated under the standards and policies established by Lessor. Final authority to initiate or terminate each flight, and otherwise to decide all matters relating to the safety of any given flight or requested flight, shall rest with the pilot-in-command of that flight. The flight crew may, in its sole discretion, terminate any flight, refuse to commence any flight, or take any other action that, in the judgment of the pilot-in-command, is necessitated by considerations of safety. No such termination or refusal to commence by the pilot-in-command shall create or support any liability for loss, injury, damage or delay in favor of Lessee or any other person. Lessor shall not be liable to Lessee or any other person for loss, injury or damage occasioned by the delay or failure to furnish the Aircraft and flight crew pursuant to this Agreement for any reason.
TRANSPORT SERVICES Upon the conclusion of such multilateral negotiations, the Parties shall conduct a review for the purpose of discussing appropriate amendments to this Agreement so as to incorporate the results of such multilateral negotiations.
All new supplies equipment and services shall include manufacturer's minimum standard warranty unless otherwise agreed to in writing. Vendor shall be legally permitted to sell all products offered for sale to TIPS Members. All goods proposed and sold shall be new unless clearly stated in writing. The Vendor shall provide timely and accurate customer support for orders to TIPS Members as agreed by the Parties. Vendors shall respond to such requests within a commercially reasonable time after receipt of the request. If support andƒor training is a line item sold or packaged with a sale, support shall be as agreed with the TIPS Member. Most TIPS Members are tax exempt and the related laws andƒor regulations of the controlling jurisdiction(s) of the TIPS Member shall apply. No assignment of Agreement may be made without the prior notification of TIPS. Written approval of TIPS shall not be unreasonably withheld. Payment for delivered goods and services can only be made to the awarded Vendor, Vendor designated reseller or vendor assigned company.
ESTIMATED / SPECIFIC QUANTITY CONTRACTS Estimated quantity contracts, also referred to as indefinite delivery / indefinite quantity contracts, are expressly agreed and understood to be made for only the quantities, if any, actually ordered during the Contract term. No guarantee of any quantity is implied or given. With respect to any specific quantity stated in the contract, the Commissioner reserves the right after award to order up to 20% more or less (rounded to the next highest whole number) than the specific quantities called for in the Contract. Notwithstanding the foregoing, the Commissioner may purchase greater or lesser percentages of Contract quantities should the Commissioner and Contractor so agree. Such agreement may include an equitable price adjustment.
