Common use of Boundary Clause in Contracts

Boundary. All flashings, valleys, drips and soakers to the Lead Development Associations details Existing Property Rear Garden The location of the boundary shall be confirmed and agreed with the adjacent owner. No part of the works shall be constructed so that it effects a trespass upon the adjacent property. All work shall be undertaken in accordance with the Party Wall agreement 'The Party Wall Act of 1996'. An agreement should also be obtained from the adjoining owner in respect to access to neighbouring properties for the purpose of construction. All work shall be carried out in strict accordance with the British Standard Codes of Practice and respective Manufacturers' Instructions. The contractor is responsible for maintaining the stability of the structure during the course of the works and as such should satisfy himself as to the condition of the structure prior to commencement of works. Should the contractor deem that temporary works are necessary to enable the works to be carried out safely, then he should employ a suitable qualified person to advise accordingly. The contractor will be responsible for the design and installation of all temporary works. Where existing walls have been assumed to be load bearing, these are to be checked and confirmed by the structural engineer prior to commencement of works and to the entire satisfaction of the building control officer. No works should commence until these plans have been approved. Should any works commence or materials ordered prior to the approval notice from the building control officer being issued, then this is done so entirely at the client/contractor's own risk and expense. All dimensions are to be checked and confirmed on site by the contractor, dimensions are not to be used for the ordering of materials or the preparation of cutting lists. Construction (Design & Management) Regulations 2015: Xxxxx-X Planning are appointed only as Principal Designer up to the production of planning & building regulations dwgs. The client, for all future works, will need to be made aware of their duties under the CDM Regulations to appoint a Principal Designer and Principal Contractor or, in the case of domestic projects, for the Principal Contractor to undertake these duties on behalf of the client. See Specification Notes drawing for list of this projects pre-construction CDM requirements. The appointed Principal Contractor (or Client) should agree or supplement this list prior to commencement of any works. GL GL General notes: This drawing must be read in conjunction with the following: 1274-01 Plans as Existing 1274-02 Elevations as Existing 1274-03 Elevations as Proposed 1274-04 Ground & First Floor Plans as Proposed 1274-05 Loft Plan as Proposed 1274-06 Section as Proposed 1274-07 B.R. Specification - - - - - - - - - - - - - - - - - - Rev Date Description PLANNING Boundary Boundary 00 Xxxxx Xxxx, Wateringbury, Kent, ME18 5DQ Tel: 00000 000000 Email: xxxx@xxxxxxxxxx.xx.xx Web: xxx.xxxxxxxxxx.xx.xx Existing Property Project Title: Xx Xxxxx Xxxxx, 00 Xxxxxxx Xxxx, Xxxxxxxxx, Xxxxxx. SE9 1XH. Drawing: Loft Conversion Elevations Existing Original Drawing Size A3 GL GL GL Existing Rear Elevation Existing Side Elevation GL Date: 08/09/2021 Drawing Number: 1274 - 02 Revision: - Scale: 1:100 @ A3 Drawn: G.J.O. Checked: S.W. This drawing is the copyright of Essan-K Planning Ltd and must not be reproduced or used without permission. Figured dimensions to be taken in preference to scaled dimensions and site dimensions must be checked before work is commenced. Copyright reserved.

Boundary. All flashings, valleys, drips and soakers to the Lead Development Associations details Existing main roof 3 No. MK08 Velux windows with Protec Star glazing to Front elevation. Velux Velux Velux Vent tiles to be Marley RidgeFast System or similar approved (min 5mm air gap) Existing Property Rear Garden The location of the boundary shall be confirmed and agreed with the adjacent owner. No part of the works shall be constructed so that it effects a trespass upon the adjacent property. All work shall be undertaken in accordance with the Party Wall agreement 'The Party Wall Act of 1996'. An agreement should also be obtained from the adjoining owner in respect to access to neighbouring properties for the purpose of construction. All work shall be carried out in strict accordance with the British Standard Codes of Practice and respective Manufacturers' Instructions. The contractor is responsible for maintaining the stability of the structure during the course of the works and as such should satisfy himself as to the condition of the structure prior to commencement of works. Should the contractor deem that temporary works are necessary to enable the works to be carried out safely, then he should employ a suitable qualified person to advise accordingly. The contractor will be responsible for the design and installation of all temporary works. Where existing walls have been assumed to be load bearing, these are to be checked and confirmed by the structural engineer prior to commencement of works and to the entire satisfaction of the building control officer. No works should commence until these plans have been approved. Should any works commence or materials ordered prior to the approval notice from the building control officer being issued, then this is done so entirely at the client/contractor's own risk and expense. All dimensions are to be checked and confirmed on site by the contractor, dimensions are not to be used for the ordering of materials or the preparation of cutting lists. Construction (Design & Management) Regulations 2015: Xxxxx-X Planning are appointed only as Principal Designer up to the production of planning & building regulations dwgs. The client, for all future works, will need to be made aware of their duties under the CDM Regulations to appoint a Principal Designer and Principal Contractor or, in the case of domestic projects, for the Principal Contractor to undertake these duties on behalf of the client. See Specification Notes drawing for list of this projects pre-construction CDM requirements. The appointed Principal Contractor (or Client) should agree or supplement this list prior to commencement of any works. GL GL General notes: This drawing must be read in conjunction with the following: 1274-01 Plans as Existing 1274-02 Elevations as Existing 1274-03 Elevations as Proposed 1274-04 Ground & First Floor Plans as Proposed 1274-05 Loft Plan as Proposed 1274-06 Section as Proposed 1274-07 B.R. Specification - - - Boundary - - - - - - - - - - - - - - - Rev Date Description PLANNING Boundary Boundary 00 Xxxxx Xxxx, Wateringbury, Kent, ME18 5DQ Tel: 00000 000000 Email: xxxx@xxxxxxxxxx.xx.xx Web: xxx.xxxxxxxxxx.xx.xx Existing Property Project Title: Xx Xxxxx Xxxxx, 00 Xxxxxxx Xxxx, Xxxxxxxxx, Xxxxxx. SE9 1XH. Drawing: Loft Conversion Elevations Existing Original Drawing Size A3 GL GL GL Existing Rear Elevation Existing Side Elevation GL Date: 08/09/2021 Drawing Number: 1274 - 02 Revision: - Scale: 1:100 @ A3 Drawn: G.J.O. Checked: S.W. This drawing is the copyright of Essan-K Planning Ltd and must not be reproduced or used without permission. Figured dimensions to be taken in preference to scaled dimensions and site dimensions must be checked before work is commenced. Copyright reserved.Boundary

Boundary. All flashings, valleys, drips and soakers to the Lead Development Associations details Rear Garden Boundary Existing Property Rear Garden The location of the boundary shall be confirmed and agreed with the adjacent owner. No part of the works shall be constructed so that it effects a trespass upon the adjacent property. All work shall be undertaken in accordance with the Party Wall agreement 'The Party Wall Act of 1996'. An agreement should also be obtained from the adjoining owner in respect to access to neighbouring properties for the purpose of construction. All work shall be carried out in strict accordance with the British Standard Codes of Practice and respective Manufacturers' Instructions. The contractor is responsible for maintaining the stability of the structure during the course of the works and as such should satisfy himself as to the condition of the structure prior to commencement of works. Should the contractor deem that temporary works are necessary to enable the works to be carried out safely, then he should employ a suitable qualified person to advise accordingly. The contractor will be responsible for the design and installation of all temporary works. Where existing walls have been assumed to be load bearing, these are to be checked and confirmed by the structural engineer prior to commencement of works and to the entire satisfaction of the building control officer. No works should commence until these plans have been approved. Should any works commence or materials ordered prior to the approval notice from the building control officer being issued, then this is done so entirely at the client/contractor's own risk and expense. All dimensions are to be checked and confirmed on site by the contractor, dimensions are not to be used for the ordering of materials or the preparation of cutting lists. Construction (Design & Management) Regulations 2015: Xxxxx-X Planning are appointed only as Principal Designer up to the production of planning & building regulations dwgs. The client, for all future works, will need to be made aware of their duties under the CDM Regulations to appoint a Principal Designer and Principal Contractor or, in the case of domestic projects, for the Principal Contractor to undertake these duties on behalf of the client. See Specification Notes drawing for list of this projects pre-construction CDM requirements. The appointed Principal Contractor (or Client) should agree or supplement this list prior to commencement of any works. GL GL General notes: This drawing must be read in conjunction with the following: 1274-01 Plans as Existing 1274-02 Elevations as Existing 1274-03 Elevations as Proposed 1274-04 Ground & First Floor Plans as Proposed 1274-05 Loft Plan as Proposed 1274-06 Section as Proposed 1274-07 B.R. Specification - - - - - - - - - - - - - - - - - - Rev Date Description PLANNING Boundary Boundary General notes: This drawing must be read in conjunction with the following: 1308-01 Plans as Existing 1308-02 Elevations as Existing 1308-03 Elevations as Proposed 1308-04 Ground Floor Plan as Proposed 1308-05 Roof Plan as Proposed 1308-06 Section as Proposed 1308-07 B.R. Specification 1308-08 Typical Drainage Details 00 Xxxxx Xxxx, Wateringbury, Kent, ME18 5DQ Tel: 00000 000000 Email: xxxx@xxxxxxxxxx.xx.xx Web: xxx.xxxxxxxxxx.xx.xx Existing Property Project Title: Xx Mr Xxxxx Xxxxx, 00 Xxxxxxx XxxxXxxxxx, XxxxxxxxxWhitstable, XxxxxxKent. SE9 1XHCT5 1AD. Existing Property Drawing: Loft Conversion Elevations Existing Original Drawing Size A3 GL GL GL Existing Single Storey Rear Elevation Existing Side Elevation GL Extension Date: 08/09/2021 07/12/2021 Drawing Number: 1274 1308 - 02 Revision: - Scale: 1:100 @ A3 Drawn: G.J.O. Checked: S.W. Elevations Existing Original Drawing Size A3 Existing Side Elevation Rear Garden This drawing is the copyright of Essan-K Planning Ltd and must not be reproduced or used without permission. Figured dimensions to be taken in preference to scaled dimensions and site dimensions must be checked before work is commenced. Copyright reserved.

Boundary. All flashings, valleys, drips and soakers to the Lead Development Associations details Existing Property Front Elevation Boundary Rear Garden GL GL Existing Flank Wall Existing Side Elevation The location of the boundary shall be confirmed and agreed with the adjacent owner. No part of the works shall be constructed so that it effects a trespass upon the adjacent property. All work shall be undertaken in accordance with the Party Wall agreement 'The Party Wall Act of 1996'. An agreement should also be obtained from the adjoining owner in respect to access to neighbouring properties for the purpose of construction. All work shall be carried out in strict accordance with the British Standard Codes of Practice and respective Manufacturers' Instructions. The contractor is responsible for maintaining the stability of the structure during the course of the works and as such should satisfy himself as to the condition of the structure prior to commencement of works. Should the contractor deem that temporary works are necessary to enable the works to be carried out safely, then he should employ a suitable qualified person to advise accordingly. The contractor will be responsible for the design and installation of all temporary works. Where existing walls have been assumed to be load bearing, these are to be checked and confirmed by the structural engineer prior to commencement of works and to the entire satisfaction of the building control officer. No works should commence until these plans have been approved. Should any works commence or materials ordered prior to the approval notice from the building control officer being issued, then this is done so entirely at the client/contractor's own risk and expense. All dimensions are to be checked and confirmed on site by the contractor, dimensions are not to be used for the ordering of materials or the preparation of cutting lists. Construction (Design & Management) Regulations 2015: Xxxxx-X Planning are appointed only as Principal Designer up to the production of planning & building regulations dwgs. The client, for all future works, will need to be made aware of their duties under the CDM Regulations to appoint a Principal Designer and Principal Contractor or, in the case of domestic projects, for the Principal Contractor to undertake these duties on behalf of the client. See Specification Notes drawing for list of this projects pre-construction CDM requirements. The appointed Principal Contractor (or Client) should agree or supplement this list prior to commencement of any works. GL GL - - - - - - Rev Date Description PLANNING General notes: This drawing must be read in conjunction with the following: 12741226-01 Plans as Existing 12741226-02 Elevations as Existing 12741226-03 Elevations as Proposed 12741226-04 Ground & First Floor Plans Plan as Proposed 12741226-05 Loft Plan as Proposed 12741226-06 Section as Proposed 12741226-07 B.R. Specification - - - - - - - - - - - - - - - - - - Rev Date Description PLANNING Boundary Boundary 00 Xxxxx Xxxx, Wateringbury, Kent, ME18 5DQ Tel: 00000 000000 Email: xxxx@xxxxxxxxxx.xx.xx Web: xxx.xxxxxxxxxx.xx.xx Original Drawing Size A3 Existing Rear Elevation Existing Property Existing Side Elevation Rear Garden Project Title: Xx Xxxxx Xxxxxxx Xxxxx, 00 Xxxxxxx Xxxx, Xxxxxxxxx, XxxxxxXxxxxxx, Xxxx. SE9 1XHME5 0XJ. Drawing: Loft Conversion Elevations Existing Original Drawing Size A3 GL GL GL Existing Rear Elevation Existing Side Elevation GL Date: 08/09/2021 06/05/2021 Drawing Number: 1274 1226 - 02 Revision: - Scale: 1:100 @ A3 Drawn: G.J.O. Checked: S.W. This drawing is the copyright of Essan-K Planning Ltd and must not be reproduced or used without permission. Figured dimensions to be taken in preference to scaled dimensions and site dimensions must be checked before work is commenced. Copyright reserved.

Boundary. All flashings, valleys, drips and soakers to the Lead Development Associations details GL Existing Property Front Elevation Boundary GL GL Existing Flank Wall Existing Side Elevation Rear Garden The location of the boundary shall be confirmed and agreed with the adjacent owner. No part of the works shall be constructed so that it effects a trespass upon the adjacent property. All work shall be undertaken in accordance with the Party Wall agreement 'The Party Wall Act of 1996'. An agreement should also be obtained from the adjoining owner in respect to access to neighbouring properties for the purpose of construction. All work shall be carried out in strict accordance with the British Standard Codes of Practice and respective Manufacturers' Instructions. The contractor is responsible for maintaining the stability of the structure during the course of the works and as such should satisfy himself as to the condition of the structure prior to commencement of works. Should the contractor deem that temporary works are necessary to enable the works to be carried out safely, then he should employ a suitable qualified person to advise accordingly. The contractor will be responsible for the design and installation of all temporary works. Where existing walls have been assumed to be load bearing, these are to be checked and confirmed by the structural engineer prior to commencement of works and to the entire satisfaction of the building control officer. No works should commence until these plans have been approved. Should any works commence or materials ordered prior to the approval notice from the building control officer being issued, then this is done so entirely at the client/contractor's own risk and expense. All dimensions are to be checked and confirmed on site by the contractor, dimensions are not to be used for the ordering of materials or the preparation of cutting lists. Construction (Design & Management) Regulations 2015: Xxxxx-X Planning are appointed only as Principal Designer up to the production of planning & building regulations dwgs. The client, for all future works, will need to be made aware of their duties under the CDM Regulations to appoint a Principal Designer and Principal Contractor or, in the case of domestic projects, for the Principal Contractor to undertake these duties on behalf of the client. See Specification Notes drawing for list of this projects pre-construction CDM requirements. The appointed Principal Contractor (or Client) should agree or supplement this list prior to commencement of any works. GL GL - - - - - - Rev Date Description PLANNING General notes: This drawing must be read in conjunction with the following: 12741289-01 Plans as Existing 12741289-02 Elevations as Existing 12741289-03 Elevations as Proposed 12741289-04 Ground & First Floor Plans Plan as Proposed 12741289-05 Loft Plan as Proposed 12741289-06 Section as Proposed 12741289-07 B.R. Specification - - - - - - - - - - - - - - - - - - Rev Date Description PLANNING 1289-08 Typical Drainage Details Boundary Boundary 00 Xxxxx Xxxx, Wateringbury, Kent, ME18 5DQ Tel: 00000 000000 Email: xxxx@xxxxxxxxxx.xx.xx Web: xxx.xxxxxxxxxx.xx.xx Existing Property Project Title: Xx Xxxxx Xxxxx, 00 Xxxxxxx XxxxMr & Xxx Xxxxxxxx, Xxxxxxxxx, XxxxxxThe Common, Sissinghurst, Kent. SE9 1XHTN17 2HU. Drawing: Existing Flank Wall Loft Conversion & Side Extension Elevations Existing GL Original Drawing Size A3 GL GL GL Existing Rear Elevation GL GL Existing Side Elevation GL Date: 08/09/2021 16/10/2021 Drawing Number: 1274 1289 - 02 Revision: - Scale: 1:100 @ A3 Drawn: G.J.O. Checked: S.W. This drawing is the copyright of Essan-K Planning Ltd and must not be reproduced or used without permission. Figured dimensions to be taken in preference to scaled dimensions and site dimensions must be checked before work is commenced. Copyright reserved.. All flashings, valleys, drips and soakers to the Lead Development Associations details 4 No. MK04 Velux windows with Protec Star glazing to Front elevation and must not project more than 150mm from the plane of the existing roof slope. Vent tiles to be Marley RidgeFast System or similar approved (min 5mm air gap) Boundary Boundary New porch entrance Cavity tray to be installed wherever new roof structure abuts adjacent walls. Min. 150mm Lead upstand into wall at appropriate course. The location of the boundary shall be confirmed and agreed with the adjacent owner. No part of the works shall be constructed so that it effects a trespass upon the adjacent property. All work shall be undertaken in accordance with the Party Wall agreement 'The Party Wall Act of 1996'. An agreement should also be obtained from the adjoining owner in respect to access to neighbouring properties for the purpose of construction. All work shall be carried out in strict accordance with the British Standard Codes of Practice and respective Manufacturers' Instructions. The contractor is responsible for maintaining the stability of the structure during the course of the works and as such should satisfy himself as to the condition of the structure prior to commencement of works. Should the contractor deem that temporary works are necessary to enable the works to be carried out safely, then he should employ a suitable qualified person to advise accordingly. The contractor will be responsible for the design and installation of all temporary works. Where existing walls have been assumed to be load bearing, these are to be checked and confirmed by the structural engineer prior to commencement of works and to the entire satisfaction of the building control officer. No works should commence until these plans have been approved. Should any works commence or materials ordered prior to the approval notice from the building control officer being issued, then this is done so entirely at the client/contractor's own risk and expense. All dimensions are to be checked and confirmed on site by the contractor, dimensions are not to be used for the ordering of materials or the preparation of cutting lists. Construction (Design & Management) Regulations 2015: Xxxxx-X Planning are appointed only as Principal Designer up to the production of planning & building regulations dwgs. The client, for all future works, will need to be 1660 Existing main roof Velux Velux Velux Velux xxxxx to receive tile hanging as indicated. 1060 Velux Plain Clay roof tiles with colour, headlap and pitch to to match existing main roof. Rear Garden made aware of their duties under the CDM Regulations to appoint a Principal Designer and Principal Contractor or, in the case of domestic projects, for the Principal Contractor to undertake these duties on behalf of the client. See Specification Notes drawing for list of this projects pre-construction CDM requirements. The appointed Principal Contractor (or Client) should agree or supplement this list prior to commencement of any works. New Rwp New Rwp - - -

Boundary. All flashings, valleys, drips and soakers to the Lead Development Associations details / panels adjusted locally to suit. Existing Property Rear Garden Boundary Warm flat roof construction (insulation over joists). See specification for confirmation The location of the boundary shall be confirmed and agreed with the adjacent owner. No part of the works shall be constructed so that it effects a trespass upon the adjacent property. All work shall be undertaken in accordance with the Party Wall agreement 'The Party Wall Act of 1996'. An agreement should also be obtained from the adjoining owner in respect to access to neighbouring properties for the purpose of construction. All work shall be carried out in strict accordance with the British Standard Codes of Practice and respective Manufacturers' Instructions. The contractor is responsible for maintaining the stability of the structure during the course of the works and as such should satisfy himself as to the condition of the structure prior to commencement of works. Should the contractor deem that temporary works are necessary to enable the works to be carried out safely, then he should employ a suitable qualified person to advise accordingly. The contractor will be responsible for the design and installation of all temporary works. Where existing walls have been assumed to be load bearing, these are to be checked and confirmed by the structural engineer prior to commencement of works and to the entire satisfaction of the building control officer. No works should commence until these plans have been approved. Should any works commence or materials ordered prior to the approval notice from the building control officer being issued, then this is done so entirely at the client/contractor's own risk and expense. All dimensions are to be checked and confirmed on site by the contractor, dimensions are not to be used for the ordering of materials or the preparation of cutting lists. Construction (Design & Management) Regulations 2015: Xxxxx-X Planning are appointed only as Principal Designer up to the production of planning & building regulations dwgs. The client, for all future works, will need to be made aware of their duties under the CDM Regulations to appoint a Principal Designer and Principal Contractor or, in the case of domestic projects, for the - - - - - - - - - - - - - - - Rev Date Description of construction build up. Roof projection to client preference. Principal Contractor to undertake these duties on behalf of the client. See Specification Notes drawing for list of this projects pre-construction CDM requirements. The appointed Principal Contractor (or Client) should agree or supplement this list prior to commencement of any works. Cavity wall construction. See specification for confirmation of construction build up. Facing Brickwork to client preference. New Flank Wall 400 min. Aluminium Caping / fascia. GL GL GL Proposed Side Elevation General notes: This drawing must be read in conjunction with the following: 12741329-01 Plans as Existing 12741329-02 Elevations as Existing 12741329-03 Elevations as Proposed 12741329-04 Ground & First Floor Plans as Proposed 1274-05 Loft Plan as Proposed 12741329-05 Roof Plan as Proposed 1329-06 Section as Proposed 12741329-07 B.R. Specification - - - - - - - - - - - - - - - - - - Rev Date Description PLANNING 1329-08 Typical Drainage Details Boundary Boundary 1 No. New double glazed multi-fold doorset to client preference. GL GL Original Drawing Size A3 Proposed Rear Elevation 2110 GL Existing main roof Existing Svp to receive proprietary collar for new flat roof penetration installed in strict accordance with manufacturers guidance. Existing window demolished / reinstated with opening reduced (raised sill level) as indicated. Area made good adjacent as necessary. Rear Garden GL 400 min. New Rwp Existing Property Proposed Side Elevation Essan-K Planning Ltd Planning & Design Consultants 00 Xxxxx Xxxx, Wateringbury, Kent, ME18 5DQ Tel: 00000 000000 Email: xxxx@xxxxxxxxxx.xx.xx Web: xxx.xxxxxxxxxx.xx.xx Existing Property Project Title: Xx Xxxxx Xxxxx, 00 Xxxxxxx Xxxx, Xxxxxxxxx, Xxxxxx. SE9 1XH. Drawing: Loft Conversion Elevations Existing Original Drawing Size A3 GL GL GL Existing Single Storey Rear Elevation Existing Side Elevation GL Extension Date: 08/09/2021 02/02/2022 Drawing Number: 1274 1329 - 02 03 Revision: - Scale: 1:100 @ A3 Drawn: G.J.O. Checked: S.W. Elevations Proposed GL This drawing is the copyright of Essan-K Planning Ltd and must not be reproduced or used without permission. Figured dimensions to be taken in preference to scaled dimensions and site dimensions must be checked before work is commenced. Copyright reserved.

Boundary. All flashings, valleys, drips and soakers to the Lead Development Associations details Existing Property Rear Garden The location of the boundary shall be confirmed and agreed with the adjacent owner. No part of the works shall be constructed so that it effects a trespass upon the adjacent property. All work shall be undertaken in accordance with the Party Wall agreement 'The Party Wall Act of 1996'. An agreement should also be obtained from the adjoining owner in respect to access to neighbouring properties for the purpose of construction. All work shall be carried out in strict accordance with the British Standard Codes of Practice and respective Manufacturers' Instructions. The contractor is responsible for maintaining the stability of the structure during the course of the works and as such should satisfy himself as to the condition of the structure prior to commencement of works. Should the contractor deem that temporary works are necessary to enable the works to be carried out safely, then he should employ a suitable qualified person to advise accordingly. The contractor will be responsible for the design and installation of all temporary works. Where existing walls have been assumed to be load bearing, these are to be checked and confirmed by the structural engineer prior to commencement of works and to the entire satisfaction of the building control officer. No works should commence until these plans have been approved. Should any works commence or materials ordered prior to the approval notice from the building control officer being issued, then this is done so entirely at the client/contractor's own risk and expense. All dimensions are to be checked and confirmed on site by the contractor, dimensions are not to be used for the ordering of materials or the preparation of cutting lists. Construction (Design & Management) Regulations 2015: Xxxxx-X Planning are appointed only as Principal Designer up to the production of planning & building regulations dwgs. The client, for all future works, will need to be made aware of their duties under the CDM Regulations to appoint a Principal Designer and Principal Contractor or, in the case of domestic projects, for the Principal Contractor to undertake these duties on behalf of the client. See Specification Notes drawing for list of this projects pre-construction CDM requirements. The appointed Principal Contractor (or Client) should agree or supplement this list prior to commencement of any works. GL GL GL Existing Side Elevation General notes: This drawing must be read in conjunction with the following: 12741329-01 Plans as Existing 12741329-02 Elevations as Existing 12741329-03 Elevations as Proposed 12741329-04 Ground & First Floor Plans as Proposed 1274-05 Loft Plan as Proposed 12741329-05 Roof Plan as Proposed 1329-06 Section as Proposed 12741329-07 B.R. Specification 1329-08 Typical Drainage Details - - - - - - - - - - - - - - - - - - - - - Rev Date Description PLANNING Boundary Boundary Existing Property 00 Xxxxx Xxxx, Wateringbury, Kent, ME18 5DQ Tel: 00000 000000 Email: xxxx@xxxxxxxxxx.xx.xx Web: xxx.xxxxxxxxxx.xx.xx Existing Property Project Title: Xx Xxxxx Xxxxx, 00 Xxxxxxx Xxxx, Xxxxxxxxx, Xxxxxx. SE9 1XH. Drawing: Loft Conversion Elevations Existing GL GL Original Drawing Size A3 GL GL GL Existing Rear Elevation GL Rear Garden GL Existing Side Elevation GL Drawing: Single Storey Rear Extension Date: 08/09/2021 02/02/2022 Drawing Number: 1274 1329 - 02 Revision: - Scale: 1:100 @ A3 Drawn: G.J.O. Checked: S.W. Elevations Existing GL This drawing is the copyright of Essan-K Planning Ltd and must not be reproduced or used without permission. Figured dimensions to be taken in preference to scaled dimensions and site dimensions must be checked before work is commenced. Copyright reserved.

Boundary. All flashings, valleys, drips and soakers to the Lead Development Associations details Note: Contractor to ensure no new construction over boundary line without neighbour agreement in place. Existing Property Rear Garden downpipe adjusted to Boundary The location of the boundary shall be confirmed and agreed with the adjacent owner. No part of the works shall be constructed so that it effects a trespass upon the adjacent property. All work shall be undertaken in accordance with the Party Wall agreement 'The Party Wall Act of 1996'. An agreement should also be obtained from the adjoining owner in respect to access to neighbouring properties for the purpose of construction. All work shall be carried out in strict accordance with the British Standard Codes of Practice and respective Manufacturers' Instructions. The contractor is responsible for maintaining the stability of the structure during the course of the works and as such should satisfy himself as to the condition of the structure prior to commencement of works. Should the contractor deem that temporary works are necessary to enable the works to be carried out safely, then he should employ a suitable qualified person to advise accordingly. The contractor will be responsible for the design and installation of all temporary works. Where existing walls have been assumed to be load bearing, these are to be checked and confirmed by the structural engineer prior to commencement of works and to the entire satisfaction of the building control officer. No works should commence until these plans have been approved. Should any works commence or materials ordered prior to the approval notice from the building control officer being issued, then this is done so entirely at the client/contractor's own risk and expense. All dimensions are to be checked and confirmed on site by the contractor, dimensions are not to be used for the ordering of materials or the preparation of cutting lists. Construction (Design & Management) Regulations 2015: avoid new papapet wall with connection to existing as indicated. Aluminium caping sized to suit new wall. New surface water to discharge into Xxxxxx / downpipe to client preference. Interlocking concrete roof tiles to match existing colour and suitable for low pitch (T.B.C. on site - approx. 20°). Existing Rwp adjusted to discharge onto new roof as necessary. Existing Svp to receive proprietary collar for new roof penetration installed in strict accordance with manufacturers guidance. Existing Property 3 No. PK04 Velux windows with Protec Star Glazing to new roof. S.E. to confirm extent of trimming adjacent. Xxxxx-X Planning are appointed only as Principal Designer up to the production of planning & building regulations dwgs. The client, for all future works, will need to be made aware of their duties under the CDM Regulations to appoint a Principal Designer and Principal Contractor or, in the case of domestic projects, for the Principal Contractor to undertake these duties on behalf of the client. See Specification Notes drawing for list of this projects pre-construction CDM requirements. The appointed Principal Contractor (or Client) should agree or supplement this list prior to commencement of any works. Proposed Rear Elevation Rear Garden New Rwp GL GL New Flank Wall Cavity wall construction. See specification for confirmation of construction build up. Dashed line represents drainage channel (beyond). Proposed Side Elevation As Existing - - - - - - - - - - - - A 01.04.22 Drawing adjusted to suit Client comments. Date Description PLANNING Rear wall painted white to match existing. Scale Bar: General notes: This drawing must be read in conjunction with the following: 12741308-01 Plans as Existing 12741308-02 Elevations as Existing 12741308-03 Elevations as Proposed 12741308-04 Ground & First Floor Plans as Proposed 1274-05 Loft Plan as Proposed 12741308-05 Roof Plan as Proposed 1308-06 Section as Proposed 12741308-07 B.R. Specification - - - - - - - - - - - - - - - - - - Rev Date Description PLANNING Boundary Boundary 1308-08 Typical Drainage Details 1m 2m 3m 4m 5m 00 Xxxxx Xxxx, Wateringbury, Kent, ME18 5DQ Tel: 00000 000000 Email: xxxx@xxxxxxxxxx.xx.xx Web: xxx.xxxxxxxxxx.xx.xx Existing Property Project Title: Xx Mr Xxxxx Xxxxx, 00 Xxxxxxx XxxxXxxxxx, XxxxxxxxxWhitstable, XxxxxxKent. SE9 1XHCT5 1AD. Existing Property Drawing: Loft Conversion Single Storey Rear Extension Elevations Existing Proposed Date: Scale: Drawn: 07/12/2021 1:100 @ A3 G.J.O. Drawing Number: 1308 - 03 GL Checked: S.W. Revision: A Original Drawing Size A3 GL GL GL Existing Rear Elevation Existing Proposed Side Elevation GL Date: 08/09/2021 Drawing Number: 1274 - 02 Revision: - Scale: 1:100 @ A3 Drawn: G.J.O. Checked: S.W. This drawing is the copyright of Essan-K Planning Ltd and must not be reproduced or used without permission. Figured dimensions to be taken in preference to scaled dimensions and site dimensions must be checked before work is commenced. Copyright reserved.