Supplemental Funding Unless otherwise defined by program rules, Supplemental Funding is the award of additional funds to provide for an increase in costs due to unforeseen circumstances. The State will comply with all Federal program agency policies and procedures for requesting supplemental grant funding. The State will comply with the following guidelines when requesting supplemental funding for the Medical Assistance Program and associated administrative payments (CFDA 93.778): The State must submit a revised Medicaid Program Budget Report (CMS-37) to request supplemental funding. The CMS guidelines and instructions for completing the CMS-37 are provided in Section 2600F of the State Medicaid Manual (SMM). The CMS/CO must receive the revised Form CMS-37 through the Medicaid Budget Expenditure System/Children's Budget Expenditure System (MBES/CBES) no later than 10 calendar days before the end of the quarter for which the supplemental grant award is being requested. Additional guidance on this policy is available from the respective CMS Regional Office, U.S. Department of Health & Human Services. The State will comply with the following guidelines when requesting supplemental funding for TANF (CFDA 93.558), CCDF (CFDA 93.575), CSE (93.563), and the FC/AA (CFDA 93.658 and CFDA 93.659) programs administered by the U.S. Department of Human Services, Administration for Children and Families (HHS/ACF):
Per-pupil Funding The School's non-facility general fund per-pupil funding shall be as defined in Sec. 302D-28, HRS. The Commission shall distribute the School's per-pupil allocation each fiscal year pursuant to Sec. 302D-28(f), HRS, and shall provide the School with the calculations used to determine the per-pupil amount each year. All funds distributed to the School from the Commission shall be used solely for the School's educational purposes as appropriated by the Legislature, and the School shall have discretion to determine how such funding shall be allocated at the school level to serve those purposes subject to applicable laws and this Contract.
Caisson Rock Caisson Rock is defined as material that must be removed from a shaft which cannot be penetrated faster than two feet per hour (fifteen minute minimum) using a rock auger with bullet-shaped hardened steel teeth (Kennametal bits or equivalent), and the drilling equipment should have the capacity to produce a continuous torque of at least 1,000,000 inch pounds and a downward force of at least 50,000 pounds (a Xxxxxx LLDH in good working condition) for piers up to seventy two inches in diameter. Use of equipment with greater torque or downward force modifies the definition of refusal to be the point at which the equipment cannot penetrate faster than two feet per hour (fifteen minute minimum). In rare cases, refusal may occur on a rock seam or boulder above the general massive rock surface. The compensation for Caisson Rock should include only material that cannot be penetrated by the rock auger at the specified rate.
Please see the current Washtenaw Community College catalog for up-to-date program requirements Secondary / Post-Secondary Program Alignment Welding HIGH SCHOOL COURSE SEQUENCE 9th Grade 10th Grade 11th Grade 12th Grade English 9 Algebra I World History/Geography Biology World Language Phys Ed/Health English 10 Geometry U.S. History/Geography Physics or Chemistry World Language Visual/Performing/Applied Arts English 11 Algebra II Civics/Economics Welding English 12 Math Credit Science Credit Welding WASHTENAW COMMUNITY COLLEGE Welding Associate in Applied Science Semester 1 Math Elective(s)* 3 WAF 105 Introduction to Welding Processes 2 WAF 111 Oxy-fuel Welding 4 WAF 112 Shielded Metal Arc Welding 4 Semester Total 13 Semester 2 Speech Elective(s) 3 WAF 106 Blueprint Reading for Welders 3 WAF 123 Advanced Oxy-fuel Welding 4 WAF 124 Advanced Shielded Metal Arc Welding 4 Semester Total 14 Semester 3 Arts/Human. Elective(s) 3 Computer Lit. Elective(s) 3 WAF 215 Advanced Gas Tungsten Arc Welding 4 WAF 288 Gas Metal Arc Welding 4 Semester Total 14 Semester 4 WAF 200 Layout Theory Welding 3 WAF 210 Welding Metallurgy 3 Soc. Sci. Elective(s) 3 WAF 226 Specialized Welding Procedures 4 Semester Total 13 Semester 5 Nat. Sci. Elective(s) 4 WAF 227 Basic Fabrication 3 WAF 229 Shape Cutting Operations 3 Writing Elective(s) 3 Semester Total 13 Program Totals 67
Provision of Interconnection Financial Security The Interconnection Customer is obligated to provide all necessary Interconnection Financial Security required under Section 11 of the GIDAP in a manner acceptable under Section 11 of the GIDAP. Failure by the Interconnection Customer to timely satisfy the GIDAP’s requirements for the provision of Interconnection Financial Security shall be deemed a breach of this Agreement and a condition of Default of this Agreement.
Lodgement of SWS wage assessment agreement C.6.1 All SWS wage assessment agreements under the conditions of this schedule, including the appropriate percentage of the relevant minimum wage to be paid to the employee, must be lodged by the employer with Fair Work Australia.
REPLACEMENT OF NOTES, COUPONS AND TALONS Should any Note, Coupon or Talon be lost, stolen, mutilated, defaced or destroyed, it may be replaced at the specified office of the Agent upon payment by the claimant of such costs and expenses as may be incurred in connection therewith and on such terms as to evidence and indemnity as the Issuer may reasonably require. Mutilated or defaced Notes, Coupons or Talons must be surrendered before replacements will be issued.
ISSUE OF REPLACEMENT NOTES, COUPONS AND TALONS 13.1 The Issuer will cause a sufficient quantity of additional forms of Notes, Coupons and Talons to be available, upon request, to the Agent at its specified office for the purpose of issuing replacement Notes, Coupons and Talons as provided below.
2023 SEIU Local 503/State of Oregon CBA 65 certificate issued by the duly licensed attending physician that the employee is physically and/or mentally able to perform the duties of the position.
VISIBILITY OF FUNDING FROM THE OFFICIAL DEVELOPMENT ASSISTANCE Unless the SAIDC requests or agrees otherwise, any communication or publication made by the Final Beneficiary that relates to the action, including at conferences, seminars or in any information or promotional materials (such as brochures, leaflets, posters, presentations in electronic form, etc.), including tangible assets acquired from the project must: (a) indicate that the action has received funding from the Official Development Assistance, SlovakAid and (b) display the SlovakAid logo. When displayed in association with another logo, the SlovakAid logo must have appropriate prominence. The obligation to display the SlovakAid logo does not confer on the Final Beneficiary a right of exclusive use. The Final Beneficiary may not appropriate the SlovakAid logo or any similar trademark or logo, either by registration or by any other means. For the purposes of the first, second and third subparagraphs and under the conditions specified therein, the Final Beneficiary may use the SlovakAid logo without first obtaining permission from the SAIDC.
