CORRECTIONS OF METERING Sample Clauses

CORRECTIONS OF METERING. ERRORS - If, upon testing, the Company's meter removed from service is found to be inaccurate by less than or equal to 1/2 of 1 percent (0.5%) (either high or low), previous recordings of such equipment shall be considered accurate in computing deliveries of electrical energy hereunder. If, upon testing, Company's meter shall be found to be inaccurate by greater than 1/2 of 1 percent (0.5%) (either high or low), any previous recordings by such Company meter shall be corrected to zero error, to the extent possible, and Company shall promptly send to Customer a report based on such corrected recordings. If no reliable information exists as to when the Company meter became inaccurate, it shall be assumed for correction purposes hereunder that such inaccuracy began at the point in time midway between the testing date and the last previous date on which the Company meter was tested and found to be accurate or adjusted to be accurate, with the adjustment period not to exceed six (6) months. a. The provisions of Subsection 1.2 pertaining to billing Customer five times the applicable demand rate for demand exceeding the Contract Demand will not apply in the event that metering inaccuracies prevent Customer from having knowledge of such potential exposure.
Sample 1
AutoNDA by SimpleDocs

Related to CORRECTIONS OF METERING

  • Metering 1. If the Producer desires to sell electric power to the Company, the Company shall provide, own and maintain at the Producer's expense all necessary meters and associated equipment to be utilized for the measurement of energy and capacity for determining the Company's payment to the Producer pursuant to an applicable agreement.

  • Cost of Metering The Issuer shall not be obligated to pay any costs associated with the routine metering duties set forth in this Section 2, including the costs of installing, replacing and maintaining meters, nor shall the Issuer be entitled to any credit against the Servicing Fee for any cost savings realized by the Servicer as a result of new metering and/or billing technologies.

  • Installation and Maintenance of Meters The Servicer shall cause to be installed, replaced and maintained meters in accordance with the Servicer Policies and Practices.

  • Inspection and Testing 7.5.1 Meters, data acquisition, and related protection equipment at Generator's Interconnection Point shall be tested at least biennially by Generator in accordance with the provisions for meter testing as established in American National Standard Institute Code for Electricity Metering (ANSI) Standard C12.16 for Solid State Electricity Meters, as the same may be updated from time to time. Representatives of each Party shall be afforded an opportunity to witness such tests.

  • Processing of Items The provision of services shall be governed by the Processor’s Treasury Management Services Agreement, Commercial Account Agreement or other applicable agreements and related service terms (individually and collectively, the “Bank Agreements”), as may be amended from time to time, subject to the prior written consent to any such amendments of a material nature by the Trustee and AmeriCredit, which consents shall not be unreasonably withheld, conditioned or delayed.

  • Repairs; Maintenance and Compliance Borrower shall at all times maintain, preserve and protect all franchises and trade names, and Borrower shall cause the Property to be maintained in a good and safe condition and repair and shall not remove, demolish or alter the Improvements or Equipment (except for alterations performed in accordance with Section 5.4.2 below and normal replacement of Equipment with Equipment of equivalent value and functionality). Borrower shall promptly comply with all Legal Requirements and immediately cure properly any violation of a Legal Requirement. Borrower shall notify Lender in writing within two (2) Business Days after Borrower first receives notice of any such non-compliance. Borrower shall promptly repair, replace or rebuild any part of the Property that becomes damaged, worn or dilapidated and shall complete and pay for any Improvements at any time in the process of construction or repair.

  • Performance and Compliance with Receivables and Contracts At its expense, timely and fully perform and comply with all material provisions, covenants and other promises, if any, required to be observed by the Issuer under the Contracts related to the Receivables.

  • Review of Materials During the term of this Agreement, Client shall ensure that all prospectuses, statements of additional information, registration statements, proxy statements, reports to shareholders, advertising and sales literature or other materials prepared for distribution to Fund shareholders or the public, which refer to the Subadviser in any way, prepared by employees or agents of Client or its affiliates are consistent with information previously provided by Subadviser. Subadviser shall promptly notify the Client of any changes to information pertaining to the Subadviser and stated in the materials described in this Section 6(g).

  • Performance and Compliance with Contracts and Credit and Collection Policy The Seller shall (and shall cause the Servicer to), at its expense, timely and fully perform and comply with all material provisions, covenants and other promises required to be observed by it under the Contracts related to the Receivables, and timely and fully comply in all material respects with the applicable Credit and Collection Policies with regard to each Receivable and the related Contract.

  • Dispositions of Equipment No Borrower shall sell, lease or otherwise dispose of any Equipment, without the prior written consent of Agent, other than (a) a Permitted Asset Disposition; and (b) replacement of Equipment that is worn, damaged or obsolete with Equipment of like function and value, if the replacement Equipment is acquired substantially contemporaneously with such disposition and is free of Liens.

Time is Money Join Law Insider Premium to draft better contracts faster.