Product Identification Before removal from Sale Area, unless Contracting Officer determines that circumstances warrant a written waiver or adjustment, Purchaser shall:
Client identification 9.1. The Company has the right to require the Client to confirm his/her registration information specified when opening a trading account. To do so, the Company may ask the Client at its own discretion and at any time to provide a notarized electronic copy of his/her identification document, bank statement or public utilities xxxx as a proof of residence. In particular cases, the Company may ask the Client to provide a photo of him/her holding his/her ID near his/her face. The detailed client identification requirements are set out in the “AML policies” section on the Company’s official site.
Non-Identification Approved Users agree not to use the requested datasets, either alone or in concert with any other information, to identify or contact individual participants from whom data and/or samples were collected. Approved Users also agree not to generate information (e.g., facial images or comparable representations) that could allow the identities of research participants to be readily ascertained. These provisions do not apply to research investigators operating with specific IRB approval, pursuant to 45 CFR 46, to contact individuals within datasets or to obtain and use identifying information under an 2 The project anniversary date can be found in “My Projects” after logging in to the dbGaP authorized-access portal. IRB-approved research protocol. All investigators including any Approved User conducting “human subjects research” within the scope of 45 CFR 46 must comply with the requirements contained therein.
Product Information EPIZYME recognizes that by reason of, inter alia, EISAI’s status as an exclusive licensee in the EISAI Territory under this Agreement, EISAI has an interest in EPIZYME’s retention in confidence of certain information of EPIZYME. Accordingly, until the end of all Royalty Term(s) in the EISAI Territory, EPIZYME shall keep confidential, and not publish or otherwise disclose, and not use for any purpose other than to fulfill EPIZYME’s obligations, or exercise EPIZYME’s rights, hereunder any EPIZYME Know-How Controlled by EPIZYME or EPIZYME Collaboration Know-How, in each case that are primarily applicable to EZH2 or EZH2 Compounds (the “Product Information”), except to the extent (a) the Product Information is in the public domain through no fault of EPIZYME, (b) such disclosure or use is expressly permitted under Section 9.3, or (c) such disclosure or use is otherwise expressly permitted by the terms and conditions of this Agreement. For purposes of Section 9.3, each Party shall be deemed to be both the Disclosing Party and the Receiving Party with respect to Product Information. For clarification, the disclosure by EPIZYME to EISAI of Product Information shall not cause such Product Information to cease to be subject to the provisions of this Section 9.2 with respect to the use and disclosure of such Confidential Information by EPIZYME. In the event this Agreement is terminated pursuant to Article 12, this Section 9.2 shall have no continuing force or effect, but the Product Information, to the extent disclosed by EPIZYME to EISAI hereunder, shall continue to be Confidential Information of EPIZYME, subject to the terms of Sections 9.1 and 9.3 for purposes of the surviving provisions of this Agreement. Each Party shall be responsible for compliance by its Affiliates, and its and its Affiliates’ respective officers, directors, employees and agents, with the provisions of Section 9.1 and this Section 9.2.
Product Data Illustrations, standard schedules, performance charts, instructions, brochures, diagrams, and other information furnished by Developer to illustrate a material, product, or system for some portion of the Work.
User Identification 6.2.5.1 Access to each Party’s corporate resources will be based on identifying and authenticating individual users in order to maintain clear and personal accountability for each user’s actions.
Product ACCEPTANCE Unless otherwise provided by mutual agreement of the Authorized User and the Contractor, Authorized User(s) shall have thirty (30) days from the date of delivery to accept hardware products and sixty (60) days from the date of delivery to accept all other Product. Where the Contractor is responsible for installation, acceptance shall be from completion of installation. Failure to provide notice of acceptance or rejection or a deficiency statement to the Contractor by the end of the period provided for under this clause constitutes acceptance by the Authorized User(s) as of the expiration of that period. The License Term shall be extended by the time periods allowed for trial use, testing and acceptance unless the Commissioner or Authorized User agrees to accept the Product at completion of trial use. Unless otherwise provided by mutual agreement of the Authorized User and the Contractor, Authorized User shall have the option to run testing on the Product prior to acceptance, such tests and data sets to be specified by User. Where using its own data or tests, Authorized User must have the tests or representative set of data available upon delivery. This demonstration will take the form of a documented installation test, capable of observation by the Authorized User, and shall be made part of the Contractor’s standard documentation. The test data shall remain accessible to the Authorized User after completion of the test. In the event that the documented installation test cannot be completed successfully within the specified acceptance period, and the Contractor or Product is responsible for the delay, Authorized User shall have the option to cancel the order in whole or in part, or to extend the testing period for an additional thirty (30) day increment. Authorized User shall notify Contractor of acceptance upon successful completion of the documented installation test. Such cancellation shall not give rise to any cause of action against the Authorized User for damages, loss of profits, expenses, or other remuneration of any kind. If the Authorized User elects to provide a deficiency statement specifying how the Product fails to meet the specifications within the testing period, Contractor shall have thirty (30) days to correct the deficiency, and the Authorized User shall have an additional sixty (60) days to evaluate the Product as provided herein. If the Product does not meet the specifications at the end of the extended testing period, Authorized User, upon prior written notice to Contractor, may then reject the Product and return all defective Product to Contractor, and Contractor shall refund any monies paid by the Authorized User to Contractor therefor. Costs and liabilities associated with a failure of the Product to perform in accordance with the functionality tests or product specifications during the acceptance period shall be borne fully by Contractor to the extent that said costs or liabilities shall not have been caused by negligent or willful acts or omissions of the Authorized User’s agents or employees. Said costs shall be limited to the amounts set forth in the Limitation of Liability Clause for any liability for costs incurred at the direction or recommendation of Contractor.
Contractor’s Staff Identification Contractor shall provide, at Contractor’s expense, all staff providing services under this Contract with a photo identification badge.
Territorial application As regards the Kingdom of the Netherlands, the present Agreement shall apply to the part of the Kingdom in Europe, to the Netherlands Antilles and to Aruba, unless the notification provided for in Article 14, paragraph (1) provides otherwise.
Product Changes Vocera shall have the right, in its absolute discretion, without liability to End User, to update to provide new functionality or otherwise change the design of any Product or to discontinue the manufacture or sale of any Product. Vocera shall notify End User at least 90 days prior to the delivery of any Product which incorporates a change that adversely affects form, fit or function (“Material Change”). Vocera shall also notify End User at least 90 days prior to the discontinuance of manufacture of any Product. Notification will be made as soon as reasonably practical for changes associated with regulatory or health and safety issues.
