Creating New Connections Sample Clauses

Creating New Connections. The New Connection dialog box is used to create new network connections. This dialog box is invoked by: Clicking on the Configure tab in the Terminal Connection Manager dialog box. Clicking on Add command button on the Configure properties sheet. The following figure shows the New Connection dialog box. New Connection Dialog Box
AutoNDA by SimpleDocs

Related to Creating New Connections

  • Conducting Negotiations 5-2-1 The Association and the District agree that negotiations shall be guided by the following procedures, which may be modified at any time by mutual consent. 5-2-2 The parties agree to negotiate in good faith. Good faith is defined as an honest attempt to resolve issues, which arise during the negotiations process. Both parties agree to present reasonable proposals, which demonstrate educational and fiscal responsibility. The obligations of good faith negotiations does not compel either party to agree or to make concessions on a specific issue. 5-2-3 The parties agree that the primary teams at the table for each side will be limited to a mutually agreed upon number of participants. A majority of each team shall be District employees.

  • Opening Negotiations 4.2.1 Between April 1 and April 30 of each ensuing year, either the Association or the Board shall submit a written request for negotiations to commence to the other party, if it desires there to be negotiations for that year. If no such request is made during the time period above, negotiations will not take place for the ensuing year.

  • Initiating Negotiations A. Upon written request by the Association to the Board, or by the Board to the Association, after September 1 and no later than November 1, the Board and the Association will arrange for negotiation as provided for herein.

  • Pressing Necessity An Employee shall be granted leave without pay for pressing necessity. Pressing necessity shall be defined as a sudden or unusual occurrence that could not, by the exercise of reasonable judgement, have been foreseen by the Employee and which requires the immediate attention of the Employee. The Employee may elect to use any entitlement to time off such as vacation, public holiday or earned time.

  • Purpose of Interconnection Facilities Except as may be required by Applicable Laws and Regulations, or as otherwise agreed to among the Parties, the Interconnection Facilities shall be constructed for the sole purpose of interconnecting the Large Generating Facility to the Participating TO’s Transmission System and shall be used for no other purpose.

  • Textual Amendments F10 Clause 3 repealed by Chevening Estate Act 1987 (c. 20, SIF 57), s. 3(1), Sch. 2 para. 6(1)(b)

  • Access Toll Connecting Trunk Group Architecture 9.2.1 If CBB chooses to subtend a Verizon access Tandem, CBB’s NPA/NXX must be assigned by CBB to subtend the same Verizon access Tandem that a Verizon NPA/NXX serving the same Rate Center Area subtends as identified in the LERG.

  • Modification of the Small Generating Facility The Interconnection Customer must receive written authorization from the NYISO and Connecting Transmission Owner before making any change to the Small Generating Facility that may have a material impact on the safety or reliability of the New York State Transmission System or the Distribution System. Such authorization shall not be unreasonably withheld. Modifications shall be done in accordance with Good Utility Practice. If the Interconnection Customer makes such modification without the prior written authorization of the NYISO and Connecting Transmission Owner, the Connecting Transmission Owner shall have the right to temporarily disconnect the Small Generating Facility. If disconnected, the Small Generating Facility will not be reconnected until the unauthorized modifications are authorized or removed.

  • Provisioning of High Frequency Spectrum and Splitter Space 3.2.1 BellSouth will provide <<customer_name>> with access to the High Frequency Spectrum as follows:

  • Skidding and Yarding Methods of skid- ding or yarding specified for particular areas, if any, are indicated on Sale Area Map. Outside Clearcutting Units and construction clearings, insofar as ground conditions permit, products shall not be skidded against reserve trees or groups of reproduction and tractors shall be equipped with a winch to facilitate skidding. B6.421 Rigging. Insofar as practicable, needed rigging shall be slung on stumps or trees desig- nated for cutting.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!