Door Assemblies Sample Clauses

Door Assemblies. Provide and install one new building standard exit door assembly, with a keyed lockset only, located in the enlarged breakroom. Re-finish existing doors as necessary.
Sample 1Sample 2
AutoNDA by SimpleDocs
Door Assemblies. 19.13.2.1 Public: Solid core wood veneer door and hollow metal frame, with standard hardware (type: storeroom lockset), hydraulic overhead door closer device and electric strike. 19.13.2.2 Staff: Solid core wood veneer door and hollow metal frame with narrow light vision panel (approx. 3” x 33”, bottom of glass 42” above finished floor ), with standard hardware (type: storeroom lockset - rev. install), hydraulic overhead door closer device and electric strike. <<controlled access point>>
Sample 1
Door Assemblies. 19.9.3.1 Client entrance hallway to interview room door assembly: Solid core wood veneer door and hollow metal frame with narrow light vision panel (approx. 3” x 33”, bottom of glass 42” above finished floor ), with standard hardware (type: storeroom lockset), hydraulic overhead door closer device and electric strike. 19.9.3.2 Staff door assembly: Solid core wood veneer door and hollow metal frame with narrow light vision panel (approx. 3” x 33”, bottom of glass 42” above finished floor ), with standard hardware (type: storeroom lockset - rev. install), hydraulic overhead door closer device and electric strike.
Sample 1
Door Assemblies. 1. 3/4 inch thick interlocking double steel pan construction with sound deadened interior. Pans shall be screw fastened together. Reinforce interior of front panel with welded steel hat channels. 2. Provide internal 14 gauge reinforcement in case and door to receive hinges. Hinges shall be
Sample 1

Related to Door Assemblies

  • Fabrication Making up data or results and recording or reporting them.

  • Assembly (a) The Contracting Parties shall have an Assembly. (b) Each Contracting Party shall be represented by one delegate who may be assisted by alternate delegates, advisors and experts. (c) The expenses of each delegation shall be borne by the Contracting Party that has appointed the delegation. The Assembly may ask WIPO to grant financial assistance to facilitate the participation of delegations of Contracting Parties that are regarded as developing countries in conformity with the established practice of the General Assembly of the United Nations or that are countries in transition to a market economy. (a) The Assembly shall deal with matters concerning the maintenance and development of this Treaty and the application and operation of this Treaty. (b) The Assembly shall perform the function allocated to it under Article 26(2) in respect of the admission of certain intergovernmental organizations to become party to this Treaty. (c) The Assembly shall decide the convocation of any diplomatic conference for the revision of this Treaty and give the necessary instructions to the Director General of WIPO for the preparation of such diplomatic conference. (a) Each Contracting Party that is a State shall have one vote and shall vote only in its own name. (b) Any Contracting Party that is an intergovernmental organization may participate in the vote, in place of its Member States, with a number of votes equal to the number of its Member States which are party to this Treaty. No such intergovernmental organization shall participate in the vote if any one of its Member States exercises its right to vote and vice versa. (4) The Assembly shall meet in ordinary session once every two years upon convocation by the Director General of WIPO. (5) The Assembly shall establish its own rules of procedure, including the convocation of extraordinary sessions, the requirements of a quorum and, subject to the provisions of this Treaty, the required majority for various kinds of decisions.

  • Tooling Unless otherwise specified in this Agreement, all tooling and/or all other articles required for the performance hereof shall be furnished by Seller, maintained in good condition and replaced when necessary at Seller's expense. If NETAPP agrees to pay Seller for special tooling or other items either separately or as a stated part of the unit price of Goods purchased herein, title to same shall be and remain in NETAPP upon payment therefore.

  • Spares Boeing will revise, as applicable, the customized Recommended Spares Parts List (RSPL) and Illustrated Parts Catalog (IPC).

  • OPEN SOURCE COMPONENTS The DS Offerings may include open source components. Whenever notices (such as acknowledgment, copies of licenses or attribution notice) are required by the original licensor, such notices are included in the Documentation of the DS Offerings. Moreover, some open source components may not be distributed and licensed under the terms of the Agreement but under the terms of their original licenses as set forth in the Documentation of the DS Offerings themselves. Source code for open source software components is available upon request. Except for components mentioned in the section EXCLUSIONS below, the warranty and indemnification provided by DS under the Agreement apply to all open source software components and shall be provided by DS and not by the original licensor, but only for the use of the DS Offerings that is in compliance with the terms of the Agreement, and in conjunction with the DS Offerings. The original licensors of said open source software components provide them on an “as is” basis and without any liability whatsoever to Customer.

  • Fittings 2.2.1 Support structure and attachment fittings for the flap structure 2.2.2 Support structure and attachment fitting for the engine pylons 2.2.3 Support structure and attachment fitting for the main landing gear 2.2.4 Support structure and attachment fitting for the center wing box

  • Appliances The Landlord shall: (check one) ☐ - Provide the following appliances: [ENTER APPLIANCES] ☐ - Not provide any appliances.

  • Computer Equipment Recycling Program If this Contract is for the purchase or lease of computer equipment, then Contractor certifies that it is in compliance with Subchapter Y, Chapter 361 of the Texas Health and Safety Code related to the Computer Equipment Recycling Program and the Texas Commission on Environmental Quality rules in 30 TAC Chapter 328.

  • Scratches appliance malfunctions and any resultant leak there from; (R) any stain, soiling or damage resulting from everyday use or which has built up over time, e.g. hair, body or suntan oils and/or lotions; (S) signs of soiling include darkened areas where the body comes into contact with the furniture (these darkened areas are signs of soil build-up, which is not covered); (T) general maintenance and overall cleaning of the furniture is the consumer’s responsibility; (U) damage due to harsh or corrosive chemicals; (V) acids, including without limitation, dyes and inks (except ballpoint), plant food and fertilizer and bleach, gum; (W) any non-operating part or decorative parts such as hinges, knobs, handles, or shelves; (X) coverage under another insurance program; (Y) delivery and/or redelivery and/or loss or damage to the Covered Product while in the course of transit; (Z) design deficiency; (AA) fabrics with “X” cleaning codes and non-colorfast fabrics and leathers; (AB) odors; (AC) variation of the color, or graining of wood or wood products, marble or leather; (AD) split leathers used in seat cushions, back cushions or top or inside arm areas; (AE) natural markings on leather, such as, healed scars, insect bites, brand marks or wrinkles, or suede, and leathers with embossed patterns other than those stimulating natural cowhide; (AF) non- bovine leathers, and other buffed leathers; (AG) stains, color loss or damage resulting from cleaning methods or products (detergents, abrasives or other harsh cleaning agents) other than those recommended by the furniture manufacturer; (AH) stone or sand abrasion; (AI) loss or damage resulting from: pre-existing conditions known to You; (AJ) wear related issues, such as but not limited to, fading, wear, seam separation, stress tears, loss of foam resiliency, pilling or fraying of any fabric on all types of furniture; (AK) color loss or cracking and peeling on any leather or vinyl; (AL) splits or bi-cast leather; (AM) furniture that is used for commercial, institutional, outdoor or rental purposes; (AN) Customer’s Own Material furniture; (AO) wicker, rattan, and teakwood furniture; (AP) massage chairs; (AQ) stains or damage to suede, split-grain leather hide or exotic leathers; (AR) manufacturer quality issues such as stress tears, fabric flaws, fading, color loss or change, loss of foam or resiliency, cracking and peeling of leather or vinyl, natural leather markings, and defects in design and workmanship; (AS) Stains or damage that occur during assembly, delivery, installation, before furniture is delivered to your residence, while the furniture is located outside of your residence, while the furniture is in storage or being moved to or from storage or between residences; (AT) Wear & Tear caused by repeated use such as scuffing, soiling, hair/body oil, perspiration, surface abrasions, pilling or fraying of fabric, loose joints; (AU) Stains or damage covered under any manufacturer warranty, recall, homeowner, renter or other insurance policy; (AV) Stains or damage caused by structural problems, appliance malfunctions, Acts of God or natural disasters, theft, vandalism or illegal activity (AW) Stains or damage caused by independent contractors

  • Drainage Systems (1) Clear culvert inlets, outlets, and sediment catching basins. (2) Maintain waterbars, drainage dips, and other water diversion measures. (3) During active use, patrol and maintain functional drainage. (4) Repair damaged culvert ends.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!