Ethical Considerations The study will be conducted in accordance with ethical principles founded in the Declaration of Helsinki. The Institutional Review Board (IRB)/Independent Ethics Committee (IEC) will review all appropriate study documentation in order to safeguard the rights, safety and well-being of the subjects. The study can only be conducted at study sites where IRB/IEC approval has been obtained. The protocol, informed consent form, Investigator’s Brochure, advertisements (if applicable), and all other forms of information given to subjects will be provided to the IRB/IEC by the Investigator. In addition, reports on the progress of the study will be submitted to the IRB/IEC by the Investigator at the appropriate intervals.
Environmental Considerations A. Company, its officers, agents, servants, employees, invitees, independent contractors, successors, and assigns will not discharge or spill any Hazardous Substance, as defined herein, into any component of the storm drainage system or onto any paved or unpaved area within the boundaries of the Premises. In addition, Company will not discharge or spill any Hazardous Substance into any component of the sanitary sewer system without first neutralizing or treating same as required by applicable anti-pollution laws or ordinances, in a manner satisfactory to Authority and other public bodies, federal, state, or local, having jurisdiction over or responsibility for the prevention of pollution of canals, streams, rivers, and other bodies of water. Company’s discharge, spill or introduction of any Hazardous Substance onto the Premises or into any component of Authority’s sanitary or storm drainage systems will, if not remedied by Company with all due dispatch, at the sole discretion of Authority, be deemed a default and cause for termination of this Agreement by Authority, subject to notice and cure. Such termination will not relieve Company of or from liability for such discharge or spill.
General Considerations a. All reports, drawings, designs, specifications, notebooks, computations, details, and calculation documents prepared by Vendor and presented to the Board pursuant to this Agreement are and remain the property of the Board as instruments of service.
Additional Considerations For each mediation or arbitration:
Special Considerations Special considerations in determining allowability of compensation will be given to any change in a non-Federal entity's compensation policy resulting in a substantial increase in its employees' level of compensation (particularly when the change was concurrent with an increase in the ratio of Federal awards to other activities) or any change in the treatment of allowability of specific types of compensation due to changes in Federal policy.
Instructions for Operators This agreement is intended to be provided to an Operator from a LEA. The Operator should fully read the agreement and is requested to complete the below areas of the agreement. Once the Operator accepts the terms of the agreement, the Operator should wet sign the agreement and return it to the LEA. Once the LEA signs the agreement, the LEA should provide a signed copy of the agreement to the Operator. Article/Exhibit Box # Description Cover Page Box # 3 Official Name of Operator Cover Page Box # 4 Date Signed by Operator Recitals Box #5 Contract Title for Service Agreement Recitals Box #6 Date of Service Agreement Article 7 Boxes #7-10 Operator’s designated representative Signature Page Boxes #15-19 Authorized Operator’s representative signature Exhibit A Box #25 Description of services provided Exhibit B All Applicable Boxes Operator notates if data is collected to provide the described services. Defines the schedule of data required for the Operator to provide the services outlined in Exhibit A Exhibit D All Applicable Boxes (Optional Exhibit): Defines deletion or return of data expectations by LEA Exhibit E All Applicable Boxes (Optional Exhibit): Operator may, by signing the Form of General Offer of Privacy Terms (General Offer, attached as Exhibit E), be bound by the terms of this DPA to any other Subscribing LEA who signs the acceptance in said Exhibit. Exhibit F Boxes # 25-29 A list of all Subprocessors used by the Operator to perform functions pursuant to the Service Agreement, list security programs and measures, list Operator’s security measures
Certification for Federal-Aid Contracts Lobbying Activities A. The CONSULTANT certifies, by signing and submitting this Contract, to the best of its knowledge and belief after diligent inquiry, and other than as disclosed in writing to the LPA prior to or contemporaneously with the execution and delivery of this Contract by the CONSULTANT, the CONSULTANT has complied with Section 1352, Title 31, U.S. Code, and specifically, that:
CONTRACTOR’S REPRESENTATIONS 8.01 In order to induce Owner to enter into this Contract, Contractor makes the following representations:
Seller’s Representations Seller represents and warrants to Buyer as follows:
Please see the current Washtenaw Community College catalog for up-to-date program requirements Secondary / Post-Secondary Program Alignment Welding HIGH SCHOOL COURSE SEQUENCE 9th Grade 10th Grade 11th Grade 12th Grade English 9 Algebra I World History/Geography Biology World Language Phys Ed/Health English 10 Geometry U.S. History/Geography Physics or Chemistry World Language Visual/Performing/Applied Arts English 11 Algebra II Civics/Economics Welding English 12 Math Credit Science Credit Welding WASHTENAW COMMUNITY COLLEGE Welding Associate in Applied Science Semester 1 Math Elective(s)* 3 WAF 105 Introduction to Welding Processes 2 WAF 111 Oxy-fuel Welding 4 WAF 112 Shielded Metal Arc Welding 4 Semester Total 13 Semester 2 Speech Elective(s) 3 WAF 106 Blueprint Reading for Welders 3 WAF 123 Advanced Oxy-fuel Welding 4 WAF 124 Advanced Shielded Metal Arc Welding 4 Semester Total 14 Semester 3 Arts/Human. Elective(s) 3 Computer Lit. Elective(s) 3 WAF 215 Advanced Gas Tungsten Arc Welding 4 WAF 288 Gas Metal Arc Welding 4 Semester Total 14 Semester 4 WAF 200 Layout Theory Welding 3 WAF 210 Welding Metallurgy 3 Soc. Sci. Elective(s) 3 WAF 226 Specialized Welding Procedures 4 Semester Total 13 Semester 5 Nat. Sci. Elective(s) 4 WAF 227 Basic Fabrication 3 WAF 229 Shape Cutting Operations 3 Writing Elective(s) 3 Semester Total 13 Program Totals 67
