FEM and CLA-to-Design Load Comparisons Sample Clauses

FEM and CLA-to-Design Load Comparisons. (CDIL LM-2) BATC shall provide preliminary Finite Element Models (FEM) and final FEMs for the WV3 Satellite for the purposes of performing coupled loads analyses. DigitalGlobe is responsible for obtaining valid CLA results from the launch service contractor and delivering those to BATC. BATC shall then compare the results of the coupled loads analyses to the design loads used in spacecraft bus and Instrument structural analysis to confirm that the resulting loads are within the design requirements as specified in the respective ICDs. The deliverables are as follows: [**Redacted**] ITAR Controlled Document - DigitalGlobe Proprietary and Confidential Use or disclosure of data is subject to the restriction on the title page of this document. WV3 Satellite Statement of Work_ Doc Number 10329656
AutoNDA by SimpleDocs

Related to FEM and CLA-to-Design Load Comparisons

  • Grammatical Conventions Whenever the context so requires, each pronoun or verb used herein shall be construed in the singular or the plural sense and each capitalized term defined herein and each pronoun used herein shall be construed in the masculine, feminine or neuter sense.

  • Maintenance and Support Services Distributor shall provide Maintenance and Support Services to all of its Customers of Licensed Software as set forth in Sections 3.4(a) and 3.4(b) below. Distributor may require Customers to provide the own First-Line Support: however, in no event shall Siebel be responsible for First-Line or Second-Line Support. Subject to Distributor's payment of the Maintenance Fees set forth in EXHIBIT A Siebel shall provide Third-Line Support to Distributor in accordance with Siebel's then current Maintenance and Support Services Policy. Distributor shall be responsible for all support related to the Value Added Offering.

  • SERVICE XXXX USE A. Controlled Affiliate recognizes the importance of a comprehensive national network of independent BCBSA licensees which are committed to strengthening the Licensed Marks and Name. The Controlled Affiliate further recognizes that its actions within its Service Area may affect the value of the Licensed Marks and Name nationwide.

  • Testing Procedure Limitations The Asset Representations Reviewer will only be required to perform the Tests, and will not be obligated to perform additional procedures on any Review Receivable or to provide any information other than a Review Report. However, the Asset Representations Reviewer may provide additional information in a Review Report about any Review Receivable that it determines in good faith to be material to the Asset Representations Review.

  • Service Levels (1) DTI shall perform the Services in accordance with the service levels (the "Service Levels") as may be agreed to from time to time in writing by DTI and the Funds (the "Service Level Agreement"). Failure to perform in a manner which equals or exceeds the Service Levels shall result in fee credits ("Fee Credits") or the Funds' right to terminate this Agreement, as set forth in the Service Level Agreement.

  • Technical Specifications Each Bloom System is an integrated system comprised of a fuel cell stack assembly and associated balance of plant components that converts a fuel into electricity using electrochemical means that (i) has a Nameplate Capacity of at least 0.5 kilowatts of electricity using an electrochemical process and (ii) has an electricity-only generation efficiency greater than thirty percent (30%).

  • System Maintenance The Trust understands that USBFS will perform periodic maintenance to the System(s), which may cause temporary service interruptions. To the extent possible, USBFS shall notify the Trust of all planned outages and will perform any necessary maintenance during non-business hours.

  • Service Level Standards The parties agree to negotiate in good faith certain service level standards that, once agreed upon, will be incorporated into this Agreement subsequent to the effective date of the Agreement.

  • Quality Specifications SANMINA-SCI shall comply with the quality specifications set forth in its Quality Manual, incorporated by reference herein, a copy of which is available from SANMINA-SCI upon request.

  • Use of Voice, Image and Likeness I give the Company permission to use my voice, image or likeness, with or without using my name, for the purposes of advertising and promoting the Company, or for other purposes deemed appropriate by the Company in its reasonable discretion, except to the extent expressly prohibited by law.

Time is Money Join Law Insider Premium to draft better contracts faster.