Payment for Forest Products Delivered Purchaser agrees to pay the State for delivered forest products at the following rate: $0.00/MBF $250.00/MBF for incorrect species delivery* $20/mbf for Utility logs (Adjusted Gross). Purchaser agrees to increase the above delivered payment rate as approved by the State in the event the location of delivery is changed per the G-026.2 clause. Purchaser will not be billed for any delivered logs that are scaled as containing metal. *When two or more log sorts from this project are delivered to the same destination, the species contained in them are not eligible for the species price reduction. Forest Products delivered that do not meet the sorting specifications in G-022.2 are considered mis-sorts. Purchaser receiving mis-sort Forest Products is required to pay the State at the bid price under this contract. However, when mis-sorted Forest Products amount to more than 5% of the total delivered sort volume, Purchaser may request approval for payment reduction for delivered volume exceeding the mis-sort threshold. Requests for payment reduction must be submitted to the State in writing prior to contract expiration. Eligibility for mis-sort payment reduction is subject to State approval and shall be determined by the State’s delivered product analysis. Forest Products determined by the State eligible for mis-sort price reduction are not eligible for any other price adjustments. Payment reduction for Forest Products deemed mis-sorted will be calculated as follows: Payment Reduction = (B x M) x R M = Mis-sorted volume exceeding threshold excluding utility R = Reduction factor* 0.2 for diameter mis-sort 0.3 for high quality mis-sort *Logs eligible for payment reduction based on multiple reduction factors will be calculated at the higher payment reduction factor. Third-party scaling organization information is required to determine Xxxxxxxx mbf for payment reduction purposes. Value will be derived from the applicable sort value as described in this contract. Scale information for determining mis-sort payment reduction eligibility must be obtained from roll-out scale. Truck-ramp, sample scaling, and/or bundle scaling information is not acceptable for determining eligibility. Purchaser’s exclusive remedy for mis-sorts shall be the payment reduction described in this clause, notwithstanding other provisions in the Uniform Commercial Code Forest Products delivered that do not meet preferred log length specifications or multiples or combinations of preferred lengths and Forest Products delivered not meeting manufacturing standards as described in clause G-024.2 are considered mis- manufactured. Purchaser receiving mis-manufactured Forest Products is required to pay the State at the bid price under this contract. However, when mis-manufactured Forest Products amount to more than 8% of the total delivered sort volume, Purchaser may request approval for payment reduction for delivered volume exceeding the mis-manufacture threshold. Requests for payment reduction must be submitted to the State in writing prior to contract expiration. Eligibility for mis-manufacture payment reduction is subject to State approval and shall be determined by the State’s delivered product analysis. Forest Products determined by the State eligible for mis-manufacture price reductions are not eligible for any other price adjustments. Payment reduction for Forest Products deemed mis-manufactured will be calculated as follows: Payment Reduction = (B x M) x (0.2) Where: B = Bid rate from P-028.2 clause M = Mis-manufactured volume exceeding threshold excluding utility Third-party scaling organization information is required to determine Xxxxxxxx mbf for payment reduction purposes. Value will be derived from the applicable sort value as described in this contract. Scale information for determining mis-manufacture payment reduction eligibility must be obtained from roll-out scale. Truck-ramp, sample scaling, and/or bundle scaling information is not acceptable for determining eligibility. Purchaser’s exclusive remedy for mis-manufacture shall be the payment reduction described in this clause, notwithstanding other provisions in the Uniform Commercial Code.
Solicitations for Subcontracts, Including Procurements of Materials and Equipment In all solicitations either by competitive bidding or negotiation made by the Engineer for work to be performed under a subcontract, including procurements of materials or leases of equipment, each potential subcontractor or supplier shall be notified by the Engineer of the Engineer's obligations under this contract and the Regulations relative to nondiscrimination on the grounds of race, color, or national origin.
Solicitations for Subcontracts, Including Procurement of Materials and Equipment In all solicitations either by competitive bidding or negotiation made by the Local Government for work to be performed under a subcontract, including procurement of materials or leases of equipment, each potential subcontractor or supplier will be notified by the Local Government of the Local Government’s obligations under this Agreement and the Acts and Regulations relative to Nondiscrimination on the grounds of race, color, or national origin.
Third Party Suppliers If Licensee wishes to obtain the Compound, Product and/or Licensed Product from a Third Party source, Licensee shall notify Pfizer through MPP of the intended source prior to making any commitments to purchase the Compound, Product and/or Licensed Product. Pfizer will determine at its sole discretion whether and on what terms to grant a license to the intended source to produce the Compound, Product and/or Licensed Product or inform Licensee whether such license already exists.
Testing of Metering Equipment Connecting Transmission Owner shall inspect and test all of its Metering Equipment upon installation and at least once every two (2) years thereafter. If requested to do so by NYISO or Developer, Connecting Transmission Owner shall, at Developer’s expense, inspect or test Metering Equipment more frequently than every two (2) years. Connecting Transmission Owner shall give reasonable notice of the time when any inspection or test shall take place, and Developer and NYISO may have representatives present at the test or inspection. If at any time Metering Equipment is found to be inaccurate or defective, it shall be adjusted, repaired or replaced at Developer’s expense, in order to provide accurate metering, unless the inaccuracy or defect is due to Connecting Transmission Owner’s failure to maintain, then Connecting Transmission Owner shall pay. If Metering Equipment fails to register, or if the measurement made by Metering Equipment during a test varies by more than two percent from the measurement made by the standard meter used in the test, Connecting Transmission Owner shall adjust the measurements by correcting all measurements for the period during which Metering Equipment was in error by using Developer’s check meters, if installed. If no such check meters are installed or if the period cannot be reasonably ascertained, the adjustment shall be for the period immediately preceding the test of the Metering Equipment equal to one-half the time from the date of the last previous test of the Metering Equipment. The NYISO shall reserve the right to review all associated metering equipment installation on the Developer’s or Connecting Transmission Owner’s property at any time.
