Felling and Bucking Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. Purchaser may buck out cull material when necessary to produce pieces meeting Utilization Standards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net scale in percentage of gross scale, or based on the merchantability factor, whichever is stated in A2. If necessary to assess extent of defect, Purchaser shall make sample saw cuts or wedges. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting. B6.000 Xxxxx Xxxxxxx. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum heights set forth in A6, except that occasional stumps of greater heights are acceptable when Purchaser determines that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed, Purchaser shall re-cut high stumps so they will not exceed heights specified in A6 and shall dispose of severed portions in the same manner as other logging debris. The xxxxx heights shown in A6 were selected with the objective of maximum reasonable utilization of the timber, unless Sale Area Map shows special areas where xxxxx heights are lower for aesthetic, land treatment, or silvicultural rea- sons.
Cutting, Patching, and Fitting The Contractor shall do all cutting, patching, and fitting of the Work that may be required to make its several parts come together properly and fit.
Switching and Tagging Rules Each Party shall provide the other Parties a copy of its switching and tagging rules that are applicable to the other Parties’ activities. Such switching and tagging rules shall be developed on a non-discriminatory basis. The Parties shall comply with applicable switching and tagging rules, as amended from time to time, in obtaining clearances for work or for switching operations on equipment.
Training and Orientation (a) No employee shall be required to work on any job or operate any piece of equipment until he/she has received proper training and instruction.
Cutting and Patching The Contractor shall be responsible for cutting, fitting or patching required to complete the Work or to make its parts fit together properly.
Aggravating and Mitigating Factors The penalties in this matter were determined in consideration of all relevant circumstances, including statutory factors as described in CARB’s Enforcement Policy. CARB considered whether the violator came into compliance quickly and cooperated with the investigation; the extent of harm to public health, safety and welfare; nature and persistence of the violation, including the magnitude of the excess emissions; compliance history; preventative efforts taken; innovative nature and the magnitude of the effort required to comply, and the accuracy, reproducibility, and repeatability of the available test methods; efforts to attain, or provide for, compliance prior to violation; action taken to mitigate the violation; financial burden to the violator; and voluntary disclosure. The penalties are set at levels sufficient to deter violations, to remove any economic benefit or unfair advantage from noncompliance, to obtain swift compliance, and the potential costs, risks, and uncertainty associated with litigation. Penalties in future cases might be smaller or larger depending on the unique circumstances of the case.
Health Screening The Contractor shall conduct a Health Needs Screen (HNS) for new members that enroll in the Contractor’s plan. The HNS will be used to identify the member’s physical and/or behavioral health care needs, special health care needs, as well as the need for disease management, care management and/or case management services set forth in Section 3.8. The HNS may be conducted in person, by phone, online or by mail. The Contractor shall use the standard health screening tool developed by OMPP, i.e., the Health Needs Screening Tool, but is permitted to supplement the OMPP Health Needs Screening Tool with additional questions developed by the Contractor. Any additions to the OMPP Health Needs Screening Tool shall be approved by OMPP. The HNS shall be conducted within ninety (90) calendar days of the Contractor’s receipt of a new member’s fully eligible file from the State. The Contractor is encouraged to conduct the HNS at the same time it assists the member in making a PMP selection. The Contractor shall also be required to conduct a subsequent health screening or comprehensive health assessment if a member’s health care status is determined to have changed since the original screening, such as evidence of overutilization of health care services as identified through such methods as claims review. Non-clinical staff may conduct the HNS. The results of the HNS shall be transferred to OMPP in the form and manner set forth by OMPP. As part of this contract, the Contractor shall not be required to conduct HNS for members enrolled in the Contractor’s plan prior to January 1, 2017 unless a change in the member’s health care status indicates the need to conduct a health screening. For purposes of the HNS requirement, new members are defined as members that have not been enrolled in the Contractor’s plan in the previous twelve (12) months. Data from the HNS or NOP form, current medications and self-reported medical conditions will be used to develop stratification levels for members in Hoosier Healthwise. The Contractor may use its own proprietary stratification methodology to determine which members should be referred to specific care coordination services ranging from disease management to complex case management. OMPP shall apply its own stratification methodology which may, in future years, be used to link stratification level to the per member per month capitation rate. The initial HNS shall be followed by a detailed Comprehensive Health Assessment Tool (CHAT) by a health care professional when a member is identified through the HNS as having a special health care need, as set forth in Section 4.2.4, or when there is a need to follow up on problem areas found in the initial HNS. The detailed CHAT may include, but is not limited to, discussion with the member, a review of the member’s claims history and/or contact with the member’s family or health care providers. These interactions shall be documented and shall be available for review by OMPP. The Contractor shall keep up-to-date records of all members found to have special health care needs based on the initial screening, including documentation of the follow-up detailed CHAT and contacts with the member, their family or health care providers.
Tests, Labs, and Imaging and X rays (diagnostic) This plan covers diagnostic tests, labs, and imaging and x-rays to diagnose or treat a condition when ordered by a physician. Major Diagnostic Imaging and Tests Major diagnostic imaging and tests include but are not limited to: • magnetic resonance imaging (MRI), • magnetic resonance angiography (MRA), • computerized axial tomography (CAT or CT scans), • nuclear scans, • positron emission tomography (PET scan), and • cardiac imaging. Preauthorization may be required for major diagnostic imaging and tests. This plan covers MRI examinations when the quality assurance standards of R.I. General Law §27-20-41 are met. MRI examinations conducted outside of the State of Rhode Island must be performed in accordance with the applicable laws of the state in which the examination has been conducted. Diagnostic Imaging and X-rays (other than the imaging services noted above) Diagnostic imaging and x-rays include but are not limited to: • general imaging (such as x-rays and ultrasounds), and • mammograms.
INTERNET PLANNING, ENGINEERING AND OPERATIONS Job Title: Internet/Web Engineer Job#: 2620 General Characteristics Integrally involved in the development and support of all Internet/Intranet/Extranet sites and supporting systems. Works closely with other IT groups and customers to define the system design and user interface based on customer needs and objectives. Participates in all phases of the development and implementation process, and may act as a project manager on special projects. Ensures the integration of the Web servers and all other supporting systems. Responsible for system tuning, optimization of information/data processing, maintenance and support of the production environment.
Weighing and Scaling Costs Purchaser agrees to pay for all weighing costs for logs delivered regardless if logs are purchased on a weight or scale basis. In addition, Purchaser agrees to pay for all scaling costs for logs delivered on a scale basis. Purchaser also agrees to pay for all costs associated with the transmission and reporting of scale or weight data.
