LUCENT CONFIGURATIONS Sample Clauses

LUCENT CONFIGURATIONS. The following additional requirements are specified for the Lucent configurations: — The Lucent configuration must be "plug and play" with the Lucent Series 2, 1 BTS, and Series 2mm hardware. Specifically, all alarms generated all rack, subracks, preamplifiers, amplifiers must appear at the Lucent Switch (MSC) as if generated from Lucent hardware directly — All external connections (RF, data, power) located on top of rack — Include 5-to-2 Combiners to support up to 4 sectors — Front and Rear access to subracks and modules possible Includes 4 pre-amplifiers — Include DC/DC Converter with redundant power supply to support any pre-amplifiers — Support up to 4 transmit antennas and subracks — Maximum width 28" — Maximum depth 35" — Support a redundant Preamplifier which meets the following specifications: Redundant Preamplifier Specifications Frequency Range 000-000 XXx Xxxxxx Multiple Carrier: TDMA, CDMA, AMPS, GSM, EDGE Gain 5-30 +/- 1 dB RF Output Power 5 dBm Max Minimum RF Output Power -40 dBm Maximum RF Output Power + 10 dBm Gain Difference between primary and seconday Section 0.5 dB DC Input Voltage 26-28 Vdc @ 1A Operating Temp 0 to +50C RF Connections SMA female CD and Logic Connector 9 pin Male D-Subminiature Gain Adjust Front Panel Control, Flat Screwdriver Fault Logic One Preamp Failure Major Two Preamp Failure Critical [***] Confidential treatment requested pursuant to a request for confidential treatment filed with the Securities and Exchange Commission. Omitted portions have been filed separately with the Commission.
Sample 1
AutoNDA by SimpleDocs

Related to LUCENT CONFIGURATIONS

  • Configuration The configuration for the Purchase Right Aircraft will be the Detail Specification for Model 767-3S2F aircraft at the revision level in effect at the time of the Supplemental Agreement. Such Detail Specification will be revised to include (i) changes required to obtain required regulatory certificates and (ii) other changes as mutually agreed upon by Boeing and Customer.

  • AIRCRAFT CONFIGURATION The guarantees defined in Paragraphs 2 and 3 below (the “Guarantees”) are applicable to the A321 Aircraft as described in the A321 Standard Specification ***** as amended by the following SCNs:

  • Designated Configuration; Trained Personnel State Street and the Fund shall be responsible for supplying, installing and maintaining the Designated Configuration at the Designated Locations. State Street and the Fund agree that each will engage or retain the services of trained personnel to enable both parties to perform their respective obligations under this Addendum. State Street agrees to use commercially reasonable efforts to maintain the System so that it remains serviceable, provided, however, that State Street does not guarantee or assure uninterrupted remote access use of the System.

  • Software Additional provisions relating to software.

  • Technical Specifications Each Bloom System is an integrated system comprised of a fuel cell stack assembly and associated balance of plant components that converts a fuel into electricity using electrochemical means that (i) has a Nameplate Capacity of at least 0.5 kilowatts of electricity using an electrochemical process and (ii) has an electricity-only generation efficiency greater than thirty percent (30%).

  • Technical Data For the purpose of this Agreement, "TECHNICAL DATA" shall mean all information of the Company in written, graphic or tangible form relating to any and all products which are developed, formulated and/or manufactured by the Company, as such information exists as of the Effective Date or is developed by the Company during the term hereof.

  • Specifications Shipper will ensure that all of its Products tendered at the Origin Point for transportation on the Pipeline System meet the applicable specifications for the Product as set forth in the Tariff (as defined below) (the “Specifications”).

  • Hardware “Hardware” means the hardware and other furniture, fixtures and equipment owned or leased and then currently being used by PROVIDER exclusively to perform the Services under any MOA or PSA or to support such performance. To the extent any such items are not used by PROVIDER exclusively to perform the Services, PROVIDER shall assist CUSTOMER or its designee in purchasing, leasing or otherwise obtaining the use of comparable items.

  • Licensed Software Section 3.17(f).......................................27

  • Changes to Specifications All Specifications and any changes thereto agreed to by the parties from time to time shall be in writing, dated and signed by the parties. Any change to the Process shall be deemed a Specification change. No change in the Specifications shall be implemented by Catalent, whether requested by Client or requested or required by any Regulatory Authority, until the parties have agreed in writing to such change, the implementation date of such change, and any increase or decrease in costs, expenses or fees associated with such change (including any change to Unit Pricing). Catalent shall respond promptly to any request made by Client for a change in the Specifications, and both parties shall use commercially reasonable, good faith efforts to agree to the terms of such change in a timely manner. As soon as possible after a request is made for any change in Specifications, Catalent shall notify Client of the costs associated with such change and shall provide such supporting documentation as Client may reasonably require. Client shall pay all costs associated with such agreed upon changes. If there is a conflict between the terms of this Agreement and the terms of the Specifications, this Agreement shall control. Catalent reserves the right to postpone effecting changes to the Specifications until such time as the parties agree to and execute the required written amendment.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!