Materials Transfer In order to facilitate the Development activities contemplated by this Agreement, either Party may provide to the other Party certain biological materials or chemical compounds Controlled by the supplying Party (collectively, “Materials”) for use by the other Party in furtherance of such Development activities. Except as otherwise provided for under this Agreement, all such Materials delivered to the other Party will remain the sole property of the supplying Party, will be used only in furtherance of the Development activities conducted in accordance with this Agreement, will not be used or delivered to or for the benefit of any Third Party, except to subcontractors, without the prior written consent of the supplying Party, and will be used in compliance with all Applicable Laws. The Materials supplied under this Agreement must be used with prudence and appropriate caution in any experimental work because not all of their characteristics may be known. Except as expressly set forth in this Agreement, THE MATERIALS ARE PROVIDED “AS IS” AND WITHOUT ANY REPRESENTATION OR WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR ANY PARTICULAR PURPOSE OR ANY WARRANTY THAT THE USE OF THE MATERIALS WILL NOT INFRINGE OR VIOLATE ANY PATENT OR OTHER PROPRIETARY RIGHTS OF ANY THIRD PARTY.
Selection of Subcontractors, Procurement of Materials and Leasing of Equipment The contractor shall not discriminate on the grounds of race, color, religion, sex, national origin, age or disability in the selection and retention of subcontractors, including procurement of materials and leases of equipment. The contractor shall take all necessary and reasonable steps to ensure nondiscrimination in the administration of this contract. a. The contractor shall notify all potential subcontractors and suppliers and lessors of their EEO obligations under this contract. b. The contractor will use good faith efforts to ensure subcontractor compliance with their EEO obligations.
Solicitations for Subcontracts, Including Procurement of Materials and Equipment In all solicitations either by competitive bidding or negotiation made by the Local Government for work to be performed under a subcontract, including procurement of materials or leases of equipment, each potential subcontractor or supplier will be notified by the Local Government of the Local Government’s obligations under this Agreement and the Acts and Regulations relative to Nondiscrimination on the grounds of race, color, or national origin.
Solicitations for Subcontracts, Including Procurements of Materials and Equipment In all solicitations either by competitive bidding or negotiation made by the Engineer for work to be performed under a subcontract, including procurements of materials or leases of equipment, each potential subcontractor or supplier shall be notified by the Engineer of the Engineer's obligations under this contract and the Regulations relative to nondiscrimination on the grounds of race, color, or national origin.
CERTIFICATION OF NO ASBESTOS CONTAINING MATERIALS OR WORK 8.1 The Contractor shall be responsible for ensuring that no asbestos containing materials or work is included within the scope of the Work. The Contractor shall take whatever measures it deems necessary to insure that all employees, suppliers, fabricators, material men, subcontractors, or their assigns, comply with this requirement. 8.2 The Contractor shall ensure that Texas Department of Health licensed individuals, consultants or companies are used for any required asbestos work including asbestos inspection, asbestos abatement plans/specifications, asbestos abatement, asbestos project management and third-party asbestos monitoring.
Subsequent Developments After the date of this Contract and until the Closing Date, Seller shall use best efforts to keep Buyer fully informed of all subsequent developments of which Seller has knowledge (“Subsequent Developments”) which would cause any of Seller’s representations or warranties contained in this Contract to be no longer accurate in any material respect.
Packaging Materials and Containers for Retail Sale 1. When packaging materials and containers in which a good is packaged for retail sales are classified in the Harmonized System with the good, they shall not be taken into account in determining whether all non-originating materials used in the production of the good undergo the applicable change in tariff classification set out in Annex 4.03. 2. When the good is subject to a requirement of regional value content, the value of these packaging materials and containers shall be taken into account as originating or non-originating materials, as the case may be, in calculating the regional value content of the good.
Loop Provisioning Involving Integrated Digital Loop Carriers 2.6.1 Where Xxxx has requested an Unbundled Loop and BellSouth uses IDLC systems to provide the local service to the End User and BellSouth has a suitable alternate facility available, BellSouth will make such alternative facilities available to Xxxx. If a suitable alternative facility is not available, then to the extent it is technically feasible, BellSouth will implement one of the following alternative arrangements for Xxxx (e.g. hairpinning): 1. Roll the circuit(s) from the IDLC to any spare copper that exists to the customer premises. 2. Roll the circuit(s) from the IDLC to an existing DLC that is not integrated. 3. If capacity exists, provide "side-door" porting through the switch. 4. If capacity exists, provide "Digital Access Cross Connect System (DACS)- door" porting (if the IDLC routes through a DACS prior to integration into the switch). 2.6.2 Arrangements 3 and 4 above require the use of a designed circuit. Therefore, non- designed Loops such as the SL1 voice grade and UCL-ND may not be ordered in these cases. 2.6.3 If no alternate facility is available, and upon request from Xxxx, and if agreed to by both Parties, BellSouth may utilize its Special Construction (SC) process to determine the additional costs required to provision facilities. Xxxx will then have the option of paying the one-time SC rates to place the Loop.
Offering Materials Furnished to Cowen The Company has delivered to Cowen one complete copy of the Registration Statement and a copy of each consent and certificate of experts filed as a part thereof, and conformed copies of the Registration Statement (without exhibits) and the Prospectus, as amended or supplemented, in such quantities and at such places as Cowen has reasonably requested.
TECHNOLOGY/KNOWLEDGE TRANSFER ACTIVITIES The goal of this task is to develop a plan to make the knowledge gained, experimental results, and lessons learned available to the public and key decision makers. • Prepare an Initial Fact Sheet at start of the project that describes the project. Use the format provided by the CAM. • Prepare a Final Project Fact Sheet at the project’s conclusion that discusses results. Use the format provided by the CAM. • Prepare a Technology/Knowledge Transfer Plan that includes: o An explanation of how the knowledge gained from the project will be made available to the public, including the targeted market sector and potential outreach to end users, utilities, regulatory agencies, and others. o A description of the intended use(s) for and users of the project results. o Published documents, including date, title, and periodical name. o Copies of documents, fact sheets, journal articles, press releases, and other documents prepared for public dissemination. These documents must include the Legal Notice required in the terms and conditions. Indicate where and when the documents were disseminated. o A discussion of policy development. State if project has been or will be cited in government policy publications, or used to inform regulatory bodies. o The number of website downloads or public requests for project results. o Additional areas as determined by the CAM. • Conduct technology transfer activities in accordance with the Technology/Knowledge Transfer Plan. These activities will be reported in the Progress Reports. • When directed by the CAM, develop Presentation Materials for an Energy Commission- sponsored conference/workshop(s) on the project. • When directed by the CAM, participate in annual EPIC symposium(s) sponsored by the California Energy Commission. • Provide at least (6) six High Quality Digital Photographs (minimum resolution of 1300x500 pixels in landscape ratio) of pre and post technology installation at the project sites or related project photographs. • Prepare a Technology/Knowledge Transfer Report on technology transfer activities conducted during the project. • Initial Fact Sheet (draft and final) • Final Project Fact Sheet (draft and final) • Presentation Materials (draft and final) • High Quality Digital Photographs • Technology/Knowledge Transfer Plan (draft and final) • Technology/Knowledge Transfer Report (draft and final)
